Abdulkadir Cengiz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdulkadir Cengiz has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Egemen Avcu
Department of Mechanical Engineering, Kocaeli University, Kocaeli 41001, Türkiye
2 shared publications - Fikret Sönmez
Manisa Celal Bayar Üniversitesi
2 shared publications - Mert Guney
Department of Civil and Environmental Engineering, School of Engineering and Digital Sciences, The Environment & Resource Efficiency Cluster (EREC), Nazarbayev University, Astana 010000, Kazakhstan
2 shared publications - Yasemin Yıldıran Avcu
Department of Mechanical Engineering, Kocaeli University, Kocaeli 41001, Türkiye
2 shared publications - Ayşe Özkılınç
Department of Mechanical Engineering, Kocaeli University, Kocaeli 41001, Turkey
1 shared publication - Berkay Gönül
Department of Mechanical Engineering, Kocaeli University, Kocaeli 41001, Turkey
1 shared publication
Latest Publications
- Open Access
Surface and Tribological Properties of Powder Metallurgical Cp-Ti Titanium Alloy Modified by Shot Peening
The present study reveals for the first time the dry sliding wear behavior of a powder metallurgical pure titanium alloy (Cp-Ti) modified by shot peening. Cp-Ti samples were manufactured via powder metallurgy, and then their surface and subsurface features were modified using a custom-made, fully automated shot-peening system. The texture isotropy rate and the highest orientation angle of the shot-peened samples were 71.5% and 36°, respectively. The Abbott curves of the shot-peened surfaces revealed that the most common areal roughness value was 5.177 μm, with a frequency of 8.1%. Shot-peened surfaces exhibited an ~20% lower wear rate than unpeened surfaces under dry sliding wear, whereas the coefficient of friction was the same for both surfaces. Micro-ploughing, micro-cutting, oxidation, and three-body abrasion wear mechanisms were observed on the shot-peened and unpeened surfaces. High resolution 3D surface topographies of worn unpeened and shot-peened surfaces revealed micro-scratches and inhomogeneities along wear tracks, which are indicative of three-body abrasion mechanisms during contact. In addition, vertical and horizontal microcracks were visible just beneath the wear track, suggesting a clear indication of plastic deformation during contact. The cross-sectional hardness maps of shot-peened samples revealed the formation of a work-hardened surface layer with shot peening, which improved the wear resistance. These findings support that shot peening can be a useful tool to modify the surface and tribological properties of powder metallurgical Cp-Ti alloys.
Open AccessSurface and Tribological Properties of Powder Metallurgical Cp-Ti Titanium Alloy Modified by Shot Peening
The present study reveals for the first time the dry sliding wear behavior of a powder metallurgical pure titanium alloy (Cp-Ti) modified by shot peening. Cp-Ti samples were manufactured via powder metallurgy, and then their surface and subsurface features were modified using a custom-made, fully automated shot-peening system. The texture isotropy rate and the highest orientation angle of the shot-peened samples were 71.5% and 36°, respectively. The Abbott curves of the shot-peened surfaces revealed that the most common areal roughness value was 5.177 μm, with a frequency of 8.1%. Shot-peened surfaces exhibited an ~20% lower wear rate than unpeened surfaces under dry sliding wear, whereas the coefficient of friction was the same for both surfaces. Micro-ploughing, micro-cutting, oxidation, and three-body abrasion wear mechanisms were observed on the shot-peened and unpeened surfaces. High resolution 3D surface topographies of worn unpeened and shot-peened surfaces revealed micro-scratches and inhomogeneities along wear tracks, which are indicative of three-body abrasion mechanisms during contact. In addition, vertical and horizontal microcracks were visible just beneath the wear track, suggesting a clear indication of plastic deformation during contact. The cross-sectional hardness maps of shot-peened samples revealed the formation of a work-hardened surface layer with shot peening, which improved the wear resistance. These findings support that shot peening can be a useful tool to modify the surface and tribological properties of powder metallurgical Cp-Ti alloys.
- Open Access
Modification of Surface and Subsurface Properties of AA1050 Alloy by Shot Peening
AA1050 Al alloy samples were shot-peened using stainless-steel shots at shot peening (SP) pressures of 0.1 and 0.5 MPa and surface cover rates of 100% and 1000% using a custom-designed SP system. The hardness of shot-peened samples was around twice that of unpeened samples. Hardness increased with peening pressure, whereas the higher cover rate did not lead to hardness improvement. Micro-crack formation and embedment of shots occurred by SP, while average surface roughness increased up to 9 µm at the higher peening pressure and cover rate, indicating surface deterioration. The areal coverage of the embedded shots ranged from 1% to 5% depending on the peening parameters, and the number and the mean size of the embedded shots increased at the higher SP pressure and cover rate. As evidenced and discussed through the surface and cross-sectional SEM images, the main deformation mechanisms during SP were schematically described as crater formation, folding, micro-crack formation, and material removal. Overall, shot-peened samples demonstrated improved mechanical properties, whereas sample surface integrity only deteriorated notably during SP at the higher pressure, suggesting that selecting optimal peening parameters is key to the safe use of SP. The implemented methodology can be used to modify similar soft alloys within confined compromises in surface features.
Open AccessModification of Surface and Subsurface Properties of AA1050 Alloy by Shot Peening
AA1050 Al alloy samples were shot-peened using stainless-steel shots at shot peening (SP) pressures of 0.1 and 0.5 MPa and surface cover rates of 100% and 1000% using a custom-designed SP system. The hardness of shot-peened samples was around twice that of unpeened samples. Hardness increased with peening pressure, whereas the higher cover rate did not lead to hardness improvement. Micro-crack formation and embedment of shots occurred by SP, while average surface roughness increased up to 9 µm at the higher peening pressure and cover rate, indicating surface deterioration. The areal coverage of the embedded shots ranged from 1% to 5% depending on the peening parameters, and the number and the mean size of the embedded shots increased at the higher SP pressure and cover rate. As evidenced and discussed through the surface and cross-sectional SEM images, the main deformation mechanisms during SP were schematically described as crater formation, folding, micro-crack formation, and material removal. Overall, shot-peened samples demonstrated improved mechanical properties, whereas sample surface integrity only deteriorated notably during SP at the higher pressure, suggesting that selecting optimal peening parameters is key to the safe use of SP. The implemented methodology can be used to modify similar soft alloys within confined compromises in surface features.