Application of Promising Electrode Materials in Contact with a Thin-Layer ZrO2-Based Supporting Electrolyte for Solid Oxide Fuel Cells
Authors:
- Denis A. OsinkinDenis A. Osinkin
- Ekaterina P. AntonovaEAEkaterina P. Antonova
- Alena S. LesnichyovaALAlena S. Lesnichyova
- Evgeniy S. TropinETEvgeniy S. Tropin
- Mikhail E. ChernovMCMikhail E. Chernov
- Efim I. ChernovECEfim I. Chernov
- Andrey S. FarlenkovAFAndrey S. Farlenkov
- Anna V. KhodimchukAKAnna V. Khodimchuk
- Vadim A. EreminVEVadim A. Eremin
- Anastasia I. KovrovaAKAnastasia I. Kovrova
- Anton V. KuzminAKAnton V. Kuzmin
- Maxim V. AnanyevMaxim V. Ananyev
Open Access
Abstract
The paper presents the results of an investigation into thin single- and triple-layer ZrO2-Sc2O3-based electrolytes prepared using the tape-casting technique in combination with promising electrodes based on La2NiO4+δ and Ni-Ce0.8Sm0.2O2-δ materials. It is shown that pressing and joint sintering of single electrolyte layers allows multilayer structures to be obtained that are free of defects at the layer interface. Electrical conductivity measurements of a triple-layer electrolyte carried out in longitudinal and transverse directions with both direct and alternating current showed resistance of the interface between the layers on the total resistance of the electrolyte to be minimal. Long-term tests have shown that the greatest degradation in resistance over time occurs in the case of an electrolyte with a tetragonal structure. Symmetrical electrochemical cells with electrodes fabricated using a screen-printing method were examined by means of electrochemical impedance spectroscopy. The polarization resistance of the electrodes was 0.45 and 0.16 Ohm∙cm2 at 800 °C for the fuel and oxygen electrodes, respectively. The distribution of relaxation times method was applied for impedance data analysis. During tests of a single solid oxide fuel cell comprising a supporting triple-layer electrolyte having a thickness of 300 microns, a power density of about 160 mW/cm2 at 850 °C was obtained using wet hydrogen as fuel and air as an oxidizing gas.Keywords
Funding Information
- Российский Фонд Фундаментальных Исследований (РФФИ) (17-08-01227)
This publication has 46 references indexed in Scilit:
- Pulsed constant voltage electrophoretic deposition of YSZ electrolyte coating on conducting porous Ni–YSZ cermet for SOFCs applicationsJournal of Alloys and Compounds, 2019
- Fuel flexibility for a turbocharged SOFC systemEnergy Procedia, 2019
- Enhancement of an IT-SOFC cathode by introducing YSZ: Electrical and electrochemical properties of La0.6Ca0.4Fe0.8Ni0.2O3-δ-YSZ compositesInternational Journal of Hydrogen Energy, 2019
- Solid oxide fuel cells supported on cathodes with large straight open pores and catalyst-decorated surfacesSolid State Ionics, 2018
- SOFC-APU systems for aircraft: A reviewInternational Journal of Hydrogen Energy, 2018
- The Geometry Effect of Cathode/Anode Areas Ratio on Electrochemical Performance of Button Fuel Cell Using Mixed Conducting MaterialsEnergies, 2018
- Numerical Study on Electrochemical Performance of Low-Temperature Micro-Solid Oxide Fuel Cells with Submicron Platinum ElectrodesEnergies, 2018
- Reversible operation of microtubular solid oxide cells using La0.6Sr0.4Co0.2Fe0.8O3-δ-Ce0.9Gd0.1O2-δ oxygen electrodesJournal of Power Sources, 2018
- Effect of Sintering Temperature and Applied Load on Anode-Supported Electrodes for SOFC ApplicationEnergies, 2016
- Single fuel cell with supported LSM cathodeRussian Journal of Electrochemistry, 2012