Mikhail E. Chernov
Research Subjects
Research Interests
Mikhail E. Chernov has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Alyona S. Lesnichyova
Institute of High-Temperature Electrochemistry UB RAS, Yekaterinburg 620137, Russia
1 shared publication - Anastasia I. Kovrova
Russian Academy of Sciences
1 shared publication - Andrey S. Farlenkov
Institute of Chemical Engineering, Ural Federal University, Yekaterinburg 620002, Russia
1 shared publication - Anna V. Khodimchuk
Laboratory of Kinetics, Institute of High-Temperature Electrochemistry, Ural Branch of the Russian Academy of Sciences, Yekaterinburg 620066, Russia
1 shared publication - Anton Valerievich Kuzmin
Vyatka State University, Kirov, Russia
1 shared publication - Denis A. Osinkin
Laboratory of Kinetics, Institute of High-Temperature Electrochemistry, Ural Branch of the Russian Academy of Sciences, Yekaterinburg 620066, Russia
1 shared publication
Latest Publications
- Open Access
Application of Promising Electrode Materials in Contact with a Thin-Layer ZrO2-Based Supporting Electrolyte for Solid Oxide Fuel Cells
The paper presents the results of an investigation into thin single- and triple-layer ZrO2-Sc2O3-based electrolytes prepared using the tape-casting technique in combination with promising electrodes based on La2NiO4+δ and Ni-Ce0.8Sm0.2O2-δ materials. It is shown that pressing and joint sintering of single electrolyte layers allows multilayer structures to be obtained that are free of defects at the layer interface. Electrical conductivity measurements of a triple-layer electrolyte carried out in longitudinal and transverse directions with both direct and alternating current showed resistance of the interface between the layers on the total resistance of the electrolyte to be minimal. Long-term tests have shown that the greatest degradation in resistance over time occurs in the case of an electrolyte with a tetragonal structure. Symmetrical electrochemical cells with electrodes fabricated using a screen-printing method were examined by means of electrochemical impedance spectroscopy. The polarization resistance of the electrodes was 0.45 and 0.16 Ohm∙cm2 at 800 °C for the fuel and oxygen electrodes, respectively. The distribution of relaxation times method was applied for impedance data analysis. During tests of a single solid oxide fuel cell comprising a supporting triple-layer electrolyte having a thickness of 300 microns, a power density of about 160 mW/cm2 at 850 °C was obtained using wet hydrogen as fuel and air as an oxidizing gas.
Open AccessApplication of Promising Electrode Materials in Contact with a Thin-Layer ZrO2-Based Supporting Electrolyte for Solid Oxide Fuel Cells
The paper presents the results of an investigation into thin single- and triple-layer ZrO2-Sc2O3-based electrolytes prepared using the tape-casting technique in combination with promising electrodes based on La2NiO4+δ and Ni-Ce0.8Sm0.2O2-δ materials. It is shown that pressing and joint sintering of single electrolyte layers allows multilayer structures to be obtained that are free of defects at the layer interface. Electrical conductivity measurements of a triple-layer electrolyte carried out in longitudinal and transverse directions with both direct and alternating current showed resistance of the interface between the layers on the total resistance of the electrolyte to be minimal. Long-term tests have shown that the greatest degradation in resistance over time occurs in the case of an electrolyte with a tetragonal structure. Symmetrical electrochemical cells with electrodes fabricated using a screen-printing method were examined by means of electrochemical impedance spectroscopy. The polarization resistance of the electrodes was 0.45 and 0.16 Ohm∙cm2 at 800 °C for the fuel and oxygen electrodes, respectively. The distribution of relaxation times method was applied for impedance data analysis. During tests of a single solid oxide fuel cell comprising a supporting triple-layer electrolyte having a thickness of 300 microns, a power density of about 160 mW/cm2 at 850 °C was obtained using wet hydrogen as fuel and air as an oxidizing gas.