Polymerization efficiency of different bulk-fill resin composites cured by monowave and polywave light-curing units: a comparative study
- 1 April 2024
- journal article
- research article
- Vol. 55 (4) , 264-272
Abstract
Objectives: The objective was to evaluate the polymerization efficiency of different bulk-fill resin-based composites cured by monowave and polywave light-curing units, by assessment of the degree of conversion and Vickers microhardness at different depths. Method and materials: Two commercially available bulk-fill resin-based composites were used: Filtek One Bulk Fill Restorative (3M ESPE) and Tetric N-Ceram Bulk Fill (IvoclarVivadent). The light-curing units utilized were two LED light-curing units: a monowave LED light-cu ring unit (BlueLEX LD-105, Monitex) and a polywave LED light-curing unit (Twin Wave GT-2000, Monitex). For each test, 20 cylindrical specimens (4 mm diameter, 4 mm thickness) were prepared from each bulk-fill resin-based composite using a Split Teflon mold. Ten specimens were light-cured by the monowave light-curing unit and the other ten were light-cured by the polywave light-cu ring u nit according to the manufacturer's recommendations. Attenuated total reflectance-Fourier t ra nsform infra red spectroscopy (ATRFTI R) was used to assess the degree of conversion, and a Vickers m icroha rd ness teste r was used to assess Vickers microhardness. Statistical analysis was performed using three-way ANOVA and Tu key post-hoc tests (P < .05). Results: The degree of conversion and Vickers microhardness in bulk-fill resin-based composites containing only camphorquinone as photoinitiator were similar when cured with either monowave or polywave light-curing units. However, bulk-fill resin-based composites containing a combination of photoinitiators exhibited significantly higher degree of conversion and Vickers microhardness when cured with a polywave light-curing unit. Although aII groups showed statistically significant differences between the top and bottom surfaces regarding degree of conversion and Vickers microhardness, aII of them showed bottom/top ratios > 809/o regarding degree of conversion and Vickers microhardness. Conclusion: The polywave light-curing unit enhanced the polymerization efficiency of bulk-fill resin-based composites especially when the latter contained a combination of photoinitiators, but does not preventtheuseofa monowave light-curing u nit. (Quintessencelnt 2024;55:264-272; dok 10.3290/j.gi.b4984231)Keywords
This publication has 43 references indexed in Scilit:
- Different depth-related polymerization kinetics of dual-cure, bulk-fill compositesDental Materials, 2019
- Monomer conversion, microhardness, internal marginal adaptation, and shrinkage stress of bulk-fill resin compositesDental Materials, 2015
- Influence of increment thickness on microhardness and dentin bond strength of bulk fill resin compositesDental Materials, 2014
- Post-cure depth of cure of bulk fill dental resin-compositesDental Materials, 2014
- Effect of radical amplified photopolymerization (RAP) in resin-based compositesClinical Oral Investigations, 2013
- A brief history of LED photopolymerizationDental Materials, 2013
- In vitro comparison of mechanical properties and degree of cure of bulk fill compositesClinical Oral Investigations, 2012
- Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED unitsJournal of Dentistry, 2012
- Evaluation of microhardness, surface roughness, and wear behavior of different types of resin composites polymerized with two different light sourcesJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2009
- Effect of delivering light in specific narrow bandwidths from 394 to 515 nm on the micro-hardness of resin compositesDental Materials, 2009