Influence of Powder Mass Flow Rates on Wear Resistance and Impact Toughness of Inconel 718 Surface Coatings
Open Access
Abstract
Optimum laser cladding processing parameters were obtained based on the study of various powder mass flow rates for the repair of 27SiMn steel parts using Inconel 718 powder. In this study, fusion coating process parameters were set according to the influence of powder mass flow rates on fusion coating properties. The cross-sectional microstructure, X-ray diffraction patterns, micro-hardness distribution, friction, wear properties, impact properties, and fracture morphology of the clad layers were investigated for the various process parameters. The results indicate that the volume fraction for the Ni3Fe phase increases and then decreases as the powder mass flow rate increases. The micro-hardness, friction properties, and impact properties of the samples followed the same trend as those of Ni3Fe. At powder mass flow rates up to 20 g/min, microstructures in the cladding layer tended to be uniform with microstructures with fine grains, and micro-hardness and impact toughness reached maximum values of 328.2 HV0.5 and 45.4 J/cm2, respectively, which show better mechanical properties and wear resistance.Keywords
Funding Information
- Foundation of Key Laboratory of National Defense Science and Technology (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- National Natural Science Foundation of China (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- Shaanxi Province Key Research and Development Plan (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- Fully mechanized mining hydraulic support remanufacturing key technology research “scientist + engineer” team (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- Innovation Fund for graduate students of Shaanxi University of Technology: Mechanism and method of multi-energy field cooperative regulation of coating shape in laser cladding additive manufacturing (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- General Special Research Project of Shaanxi Provincial Department of Education (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- Research Fund of Shaanxi University of Technology (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
- Laser additive remanufacturing process and shape control method for functional coatings (JCKY61420052022, 52075544, S2022-YF-YBGY-0437, 2023KXJ-123, SLGYCX2311, 22JK0312, SLG2123, SLGKYXM2306)
This publication has 39 references indexed in Scilit:
- Microstructure and mechanical properties of Ti–C–TiN-reinforced Ni204-based laser-cladding composite coatingCeramics International, 2021
- Microstructural evolution and mechanical performance of in-situ TiB2/AlSi10Mg composite manufactured by selective laser meltingJournal of Alloys and Compounds, 2021
- Optimization of microstructure and properties of composite coatings by laser cladding on titanium alloyCeramics International, 2021
- An overview of wire arc additive manufacturing (WAAM) in shipbuilding industryShips and Offshore Structures, 2020
- Investigation of dissolution behavior of laves phase in inconel 718 fabricated by laser directed energy depositionAdditive Manufacturing, 2020
- Review and propositions for the sliding/impact wear behavior in a contact interfaceChinese Journal of Aeronautics, 2020
- Laser cladding technique for erosive wear applications: a reviewMaterials Research Express, 2020
- Improved hardness and wear resistance of plasma sprayed nanostructured NiCrBSi coating via short-time heat treatmentSurface and Coatings Technology, 2018
- Impact toughness of specimens cut out from the rollers of machines for continuous casting of blanks with fused layersMaterials Science, 2013
- Evaluation of the volume fraction of nanocrystals devitrified in Al-based amorphous alloysJournal of Non-Crystalline Solids, 2009