Advanced Fin Design for Efficient Heat Transfer in Double‐Pipe Latent Heat Thermal Storage: A Comparative Study of Straight and Inclined Multielement Fins
Authors:
- Hosseinali RamezanimouzirajiHRHosseinali Ramezanimouziraji
- Saeid Pour NematSNSaeid Pour Nemat
- Hayder I. MohammedHayder I. Mohammed
- Bhupendra Singh ChauhanBCBhupendra Singh Chauhan
- Khalil HajlaouiKHKhalil Hajlaoui
- Nashmi H. AlrasheediNANashmi H. Alrasheedi
- Pouyan TalebizadehsardariPTPouyan Talebizadehsardari
Open Access
- 1 January 2026
- journal article
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1)
Abstract
The inherently low thermal conductivity of phase change materials (PCMs) in latent heat thermal energy storage (LHTES) systems hampers efficient heat transfer during melting and solidification processes. This study aims to enhance PCM thermal performance by optimizing fin geometry within a vertical double‐pipe heat exchanger, with a focus on inclined multielement fin configurations. Novelty lies in the systematic investigation of fin orientation (30°, 35°, and 40°), number, thickness, and flow direction through detailed two‐dimensional axisymmetric simulations using ANSYS Fluent. The model incorporates buoyancy‐driven convection via the Boussinesq approximation and has been validated against experimental benchmarks with <3% deviation. Results reveal that an inclined three‐element fin configuration at a 40° angle (Case 3‐3) outperforms conventional straight fins (Case 0), increasing melting rate by 6.5% (48.16 W vs. 45.24 W) and reducing melting time by 2.3% (2470 s vs. 2529 s). During solidification, Case 3‐3 also demonstrates superior performance with a 20.8% higher discharging rate (35.42 W vs. 28.05 W) and 18.4% shorter solidification time (3497 s vs. 4352 s). Excessive fin thickness (up to 1.2x baseline) and suboptimal flow direction were shown to reduce performance by up to 25.5%. These findings provide critical insights for thermal system designers by demonstrating how geometric tailoring of fins can substantially boost energy storage and retrieval rates in PCM‐based systems. The proposed configurations offer a practical route to more compact, efficient, and responsive LHTES systems for renewable heating, industrial recovery, and building applications.Keywords
Funding Information
- Deanship of Scientific Research, Imam Mohammed Ibn Saud Islamic University (IMSIU-DDRSP2603)
This publication has 44 references indexed in Scilit:
- Numerical study on discharging process of a latent heat triple-tube heat exchanger in the presence of a central plate using the enthalpy–porosity approachJournal of Thermal Analysis and Calorimetry, 2023
- CFD analysis on optimizing the annular fin parameters toward an improved storage response in a triple‐tube containment systemEnergy Science & Engineering, 2022
- Effect of fins and nanoparticles in the discharge performance of PCM thermal storage system with a multi pass finned tube heat exchangeApplied Thermal Engineering, 2022
- Eccentricity optimization of an inner flat-tube double-pipe latent-heat thermal energy storage unitCase Studies in Thermal Engineering, 2021
- The micro‐/nano‐PCMs for thermal energy storage systems: A state of art reviewInternational Journal of Energy Research, 2019
- Review on heat transfer analysis in thermal energy storage using latent heat storage systems and phase change materialsInternational Journal of Energy Research, 2018
- Thermal energy charging behaviour of a heat exchange device with a zigzag plate configuration containing multi-phase-change-materials (m-PCMs)Applied Energy, 2015
- Melting of PCM in a thermal energy storage unit: Numerical investigation and effect of nanoparticle enhancementInternational Journal of Energy Research, 2012
- Numerical simulation on phase-change thermal storage/release in a plate-fin unitApplied Thermal Engineering, 2011
- Experimental and numerical investigation of thermal energy storage with a finned tubeInternational Journal of Energy Research, 2005