Effect of Annealing Atmosphere on the Microstructure and High-Frequency Magnetic Properties of FeSiCr Soft Magnetic Composites
Open Access
- 12 May 2026
- journal article
- research article
- Published by MDPI AG in Magnetochemistry
- Vol. 12 (5) , 57
Abstract
Annealing is a critical step in the fabrication of soft magnetic composites (SMCs), and precise coordination of annealing atmosphere and temperature is essential for optimizing their performance. In this study, FeSiCr SMCs were annealed under three different atmospheres (air, nitrogen, and argon) across a range of temperatures, and the effects of the annealing atmosphere on their microstructure and soft magnetic properties were systematically investigated. The results demonstrate that annealing in an inert atmosphere, particularly argon, within the temperature range of 450–750 °C, yields superior magnetic properties compared with air annealing. After annealing under argon at 550 °C, the effective magnetic permeability (μe) reached 47.5, and the power loss (Pcv) was 1457.3 kW/m3 at 1000 kHz and 30 mT. These improvements are primarily attributed to effective stress relaxation and the substantial retention of the polyvinyl butyral (PVB) insulating layer. With further increases in annealing temperature, the magnetic properties deteriorate rapidly due to the complete decomposition of PVB and the formation of conductive chromium carbides. Under such conditions, air annealing exhibits distinct advantages. Selective oxidation of FeSiCr occurs, leading to the formation of a dense chromium oxide insulating layer that enhances magnetic performance (after annealing at 850 °C, μe = 47.9, Pcv = 1632.0 kW/m3). Moreover, the mechanical properties were significantly improved, with the radial crush strength increasing from 22.36 N in the unannealed state to 330 N after annealing. These results indicate that the comprehensive performance of SMCs can be effectively tailored through the appropriate selection of annealing atmosphere and temperature, providing valuable guidance for the design and optimization of high-performance SMCs.Keywords
Funding Information
- Key R&D Project of Zhejiang Provincial Department of Science and Technology (2024C01146)
- Advanced Materials-National Science and Technology Major Project (2024ZD0606800)
- Intergovernmental International Science, Technology and Innovation Cooperation Key Project of the National Key R&D Programme (2022YFE0109800)
This publication has 53 references indexed in Scilit:
- Effects of oxygen on amorphous formation, magnetic properties and bending ductility in FeBCCu amorphous alloyApplied Physics A, 2023
- Microstructure and magnetic properties of FeSiCr soft magnetic powder cores with a MgO insulating layer prepared by the sol-gel methodCeramics International, 2022
- The enhanced magnetic properties of FeSiCr powder cores composited with carbonyl iron powderJournal of Materials Science: Materials in Electronics, 2021
- Novel Fabrication Method for a High-Performance Soft-Magnetic Composite Composed of Alumina-Coated Fe-Based Metal PowderJournal of Electronic Materials, 2020
- Investigation of Surface Segregation in Fe-Cr-Si Alloys by XPSMetallurgical and Materials Transactions A, 2020
- High permeability and low loss bioinspired soft magnetic composites with nacre-like structure for high frequency applicationsActa Materialia, 2019
- Green preparation of in situ Cr3C2 nano-coatings on graphite surface and their water-wettability and rheological propertiesCeramics International, 2018
- Investigation of structural, optical, dielectric and magnetic studies of Mn substituted BiFeO3 multiferroicsCeramics International, 2017
- Magnetic Materials and Devices for the 21st Century: Stronger, Lighter, and More Energy EfficientAdvanced Materials, 2010
- On the determination of atomic charge via ESCA including application to organometallicsJournal of Electron Spectroscopy and Related Phenomena, 1996