JHJerome F. Hajjar

Jerome F. Hajjar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jerome F. Hajjar has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design for Deconstruction for Sustainable Composite Steel-Concrete Floor Systems

    by Jerome F. Hajjar, Lizhong Wang, Mark D. Webster

    Conventional steel-concrete composite floor systems utilizing steel headed stud anchors and metal decks are cost-effective and widely used solutions for non-residential multi-story buildings, due in part to their enhanced strength and stiffness relative to non-composite systems. Because these systems use steel headed stud anchors welded onto steel flanges and encased in cast-in-place concrete slabs to achieve composite action, it is not possible to readily deconstruct and reuse the steel beams and concrete slabs. As the building industry is moving towards sustainability, there are clear needs for developing sustainable steel-concrete composite floor systems to facilitate material reuse, minimize consumption of raw materials, and reduce end-of-life building waste. This paper presents the behavior and design strategies for a sustainable steel-concrete composite floor system. In this system, deconstructable clamping connectors are utilized to attach precast concrete planks to steel beams to achieve composite action. The load-slip behavior of the clamping connectors was studied in pushout tests, and the test results showed that the clamping connectors possess similar shear strength to 19 mm diameter shear studs and much greater slip capacity. Four full-scale beam tests were performed to investigate the flexural behavior of the deconstructable composite beams under gravity loading and validate the connector behavior attained from the pushout tests. All the beams behaved in a ductile manner. The flexural strengths of the composite beam specimens closely match the strengths predicted for composite beams by the design provisions of the American Institute of Steel Construction (AISC).

  • Experimental Investigation of Deconstructable Steel-Concrete Shear Connections in Sustainable Composite Beams

    by Lizhong Wang, Mark D. Webster, Jerome F. Hajjar

    A new deconstructable composite floor system consisting of precast concrete planks and deconstructable clamping connections is proposed to promote sustainable design of composite flooring systems in steel buildings through reuse of the structural components. This paper presents an experimental testing program to demonstrate the strength and ductility of the deconstructable connectors and the behavior of the structural floor framing system.


  • Automated Structural Modelling of Bridges from Laser Scanning

    by Yujie Yan, Burcu Guldur, Jerome F. Hajjar

    Creation of high-fidelity finite element models (FEMs) is an important prerequisite of finite element analysis which is widely used for assessing the health condition of structures and infrastructures. Currently, most FEMs are created by professional engineers based on as-designed condition. For aging structures and infrastructures, the as-is conditions might vary significantly from as-designed conditions due to accumulated damage. In order to capture as-is conditions, 3D laser scanners have become increasingly available because of their capability of capturing massive spatial data with high accuracy in a short period of time. However, currently, the creation of FEMs from laser scan data is still a manual process which is labor-intensive and might be error-prone. This research investigates an automatic approach of using spatial data from laser scanning along with computer vision techniques for creating high-fidelity FEMs automatically. Distinct point features from raw laser point cloud is established first. The extracted point features are then integrated with prior information available on the distributions and shapes of structural components for detecting and recognizing these components. Additional steps are proposed to extract geometric information for structural components with common shapes such as wide flange beams and cylindrical concrete piers. At the end, a methodology of converting point cloud data or extracted geometric information into all-hexahedral finite element meshes is presented.


  • Stability Analysis and Design of Composite Structures

    by Mark D. Denavit, Jerome F. Hajjar, Tiziano Perea, Roberto T. Leon

    The direct analysis method is the primary means of assessing system stability within a standard specification. This method, and in particular its use of reduced stiffness, has been thoroughly validated for use in frames consisting of structural steel members. However, appropriate stiffness reductions have not yet been established nor has the method as a whole been validated for frames with steel-concrete composite columns. Through comparisons between second-order inelastic analysis results and results from the design methodology on a parametric suite of small frames, the current design provisions are evaluated in this paper. The results indicate that while the current design provisions are safe and accurate for the majority of common cases, there exist cases in which the current provisions result in high levels of unconservative error. Modifications to the current design provisions are proposed to address these issues.


  • Problems in Determining the Buckling Loads of Slender Full-Scale Concrete-Filled Tube Specimens

    by Tiziano Perea, Roberto T. Leon, Mark D. Denavit, Jerome F. Hajjar

    This paper describes the methodology for post-processing experimental data related to the axial strength of slender full-scale concrete-filled tubes. Although utilizing a state-of-the-art testing system, the results obtained during testing needed to be corrected to account for the compliance, frictional forces, resolution and capacity limits of the testing system, as well as the initial imperfections of the specimens. A complex load protocol, aimed at determining the buckling load capacity of CFT columns, a set of points in the P-M interaction diagram of CFT beam-columns, and the torsional strength of CFT members, was used. This load protocol consisted of a set of load cases applied sequentially: (1) pure compression, (2) uniaxial and biaxial bending combined with different constant axial load levels, and (3) torsion with and without constant compression loading. Successful post-processing of the data required the application of different techniques to correct, filter and extrapolate the measured experimental response. In addition, these efforts required that behavior of the loading system be characterized through integration of data from different sensors and computational simulations using stiffness and displacements obtained directly from the test.

  • Seismic Behavior of Steel-Concrete Composite Frame Structures and Design Practice in the United States

    by Mark D. Denavit, Jerome F. Hajjar, Tiziano Perea, Roberto T. Leon

    Steel-concrete composite frames have been shown to be a sensible option for use as the primary seismic force resisting system of building structures. However, there remains little data to justify the structural system performance factors (i.e., R, Cd, and Ωo) that characterize the overstrength and ductility of these systems, which are a vital component of successful design in the United States. Based on a suite of new finite element formulations, this work investigates the behavior of composite moment and braced frames under seismic loading and develops rational system performance factors. A set of archetype frames, selected to be representative of the range of frames seen in practice, were designed according to current design specifications. Nonlinear static pushover and transient dynamic analyses were performed on the frames to generate the statistical data on the seismic response from which the performance factors are quantified. The results from this investigation enable a better understanding of the variability in collapse performance of composite frame systems and will facilitate more effective designs of these systems.

  • Damage Detection on Structures Using Texture Mapped Laser Point Clouds

    by Burcu Guldur, Jerome F. Hajjar

    Damage due to age or accumulated damage from hazards on existing structures poses a worldwide problem. In order to evaluate the current status of aging, deteriorating and damaged structures, it is vital to accurately assess the present conditions. It is possible to capture the in situ condition of structures by using laser scanners that create dense 3D point clouds. However, extracting meaningful information from point clouds is automatically challenging, and the current state-of-the-art requires a certain amount of user-interaction. Previously in our research, widely accepted point cloud processing steps were used to divide laser scanner data into meaningful object clusters on which several damage detection methods were applied. Our current focus is on combining useful information extracted from laser scanner data with color information since novel laser scanners are capable of recording color data mapped on 3D point clouds. The color data provides additional information in the 4th dimension, which makes it possible to detect damage types such as cracks, corrosion, and related surface defects that are generally difficult to detect by using only laser scanner data. It also helps to track volumetric changes on structures such as spalling. Even though crack and corrosion detection from images with varying resolution are extensively researched topics, damage detection by using laser scanners with and without images is a new research area that holds many opportunities for enhancing current practice in structural health monitoring. The aim of our research is to benefit from the best features of both laser scans and images, and combine them to create an automatic and effective damage detection method which will complement the need for skilled labor during visual inspections of damaged structures and allow documenting related information automatically. This work is of interest to researchers who are focused on structural health monitoring and interested in the use of new laser scanners and damage detection algorithms for structures. As well, practitioners will benefit from exploring new methods for improving their understanding of laser scanning technology and its capabilities for robust damage detection and documentation.


  • Validation of a Finite Element Approach to Modeling of Structural Collapse of Steel Structures

    by Vitaliy V. Saykin, Tam H. Nguyen, Jerome F. Hajjar, Derya Deniz, Junho Song

    The prediction of collapse of structures has gained growing attention recently, as it is important to be able to predict and model structural collapse due to extreme loads. A lack of accurate and validated structural collapse models significantly limits the structural engineering community to predict possible extreme loads that precipitate collapse. This paper proposes an integrated platform for validated prediction of collapse of steel structures that accounts for material softening followed by elimination of finite elements to enable simulation of fracture. The proposed approach employs a void growth model (VGM) to simulate the initiation of softening and the Hillerborg model for modeling the softening itself, followed by an element deletion strategy that is developed in this framework. The parameters of these models were calibrated to a comprehensive set of experimental test results of circumferentially notched tensile (CNT) coupon specimens. These calibrated models were then validated through comparison with a broad array of experimental test results of steel structures, ranging in complexity from tensile coupons to moment-resisting beam-to-column connections. The proposed approach is shown to be accurate. Through element deletion, the formulation can account for complete structural component separation, thus precipitating modeling of the collapse of structures. This approach thus enables high-fidelity parametric simulation capabilities of interest to researchers, practitioners, and code developers who address collapse of structures.


  • Shear and Friction Response of Nonseismic Laminated Elastomeric Bridge Bearings Subject to Seismic Demands

    by Joshua S. Steelman, Larry A. Fahnestock, Evgueni T. Filipov, James M. LaFave, Jerome F. Hajjar, Douglas A. Foutch

    Laminated elastomeric bridge bearings are commonly used in areas with low-to-moderate seismicity, although the applications are typically intended for service-level considerations such as thermal movements of the bridge superstructure. These components provide a potential source of displacement capacity frequently neglected in seismic design. An experimental program was carried out to evaluate the behavioral characteristics and performance of steel-reinforced, laminated elastomeric bearings, which had not been designed for seismic demands, as the primary quasi-isolation components for seismic events by permitting slip at the interface of the bearing and substructure. The rubber at the top of the bearing is vulcanized to a steel plate, which is bolted to the test frame to simulate a connection to the superstructure. At the base of the bearing, the elastomer directly contacts concrete representing the substructure, with no restraint of horizontal motion other than friction. The elastomeric bearings ...


  • Open Access

    Data Processing of Point Clouds for Object Detection for Structural Engineering Applications

    by Sara B. Walsh, Daniel J. Borello, Burcu Guldur, Jerome F. Hajjar