Joshua S. Steelman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Joshua S. Steelman has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Douglas A. Foutch
Professor Emeritus, Dept. of Civil and Environmental Engineering, Univ. of Illinois, Urbana, IL 61801
3 shared publications - Evgueni T. Filipov
Department of Civil and Environmental Engineering Deployable and Reconfigurable Structures Laboratory University of Michigan Ann Arbor MI USA
3 shared publications - James M. LaFave
Univ. of Illinois Urbana-Champaign
3 shared publications - Jerome F. Hajjar
Northeastern Univ
3 shared publications - Larry A. Fahnestock
Univ. of Illinois Urbana-Champaign
3 shared publications
Latest Publications
- 1 July 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 18 (7) , 612-623
Shear and Friction Response of Nonseismic Laminated Elastomeric Bridge Bearings Subject to Seismic Demands
Laminated elastomeric bridge bearings are commonly used in areas with low-to-moderate seismicity, although the applications are typically intended for service-level considerations such as thermal movements of the bridge superstructure. These components provide a potential source of displacement capacity frequently neglected in seismic design. An experimental program was carried out to evaluate the behavioral characteristics and performance of steel-reinforced, laminated elastomeric bearings, which had not been designed for seismic demands, as the primary quasi-isolation components for seismic events by permitting slip at the interface of the bearing and substructure. The rubber at the top of the bearing is vulcanized to a steel plate, which is bolted to the test frame to simulate a connection to the superstructure. At the base of the bearing, the elastomer directly contacts concrete representing the substructure, with no restraint of horizontal motion other than friction. The elastomeric bearings ...
- 1 July 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 18 (7) , 612-623
Shear and Friction Response of Nonseismic Laminated Elastomeric Bridge Bearings Subject to Seismic Demands
Laminated elastomeric bridge bearings are commonly used in areas with low-to-moderate seismicity, although the applications are typically intended for service-level considerations such as thermal movements of the bridge superstructure. These components provide a potential source of displacement capacity frequently neglected in seismic design. An experimental program was carried out to evaluate the behavioral characteristics and performance of steel-reinforced, laminated elastomeric bearings, which had not been designed for seismic demands, as the primary quasi-isolation components for seismic events by permitting slip at the interface of the bearing and substructure. The rubber at the top of the bearing is vulcanized to a steel plate, which is bolted to the test frame to simulate a connection to the superstructure. At the base of the bearing, the elastomer directly contacts concrete representing the substructure, with no restraint of horizontal motion other than friction. The elastomeric bearings ...
- 13 April 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 276-288
Computational Analyses of Quasi-Isolated Bridges with Fusing Bearing Components
Computational systems analyses are described for bridge systems that employ quasi-isolation by using a set of fixed bearings in addition to isolation bearings such as elastomeric bearings with an elastomer-concrete sliding interface or elastomeric bearings with a PTFE (Teflon) to stainless steel sliding interface. The system uses stiffened L-shaped retainer brackets that limit transverse displacement of elastomeric bearings and the bridge is intended to respond predictably, reliably, and elastically under service loading (including small seismic events), but for larger seismic events, certain bridge bearing components are intended to "fuse" and experience nonlinear behaviors that can allow for passive quasi-isolation of the bridge superstructure. To facilitate the computational modeling, experimental findings from ongoing research are being used to formulate phenomenological element models that simulate nonlinear fusing behaviors in the bridge bearings and auxiliary components. Furthermore the substructure pier elements, the bridge foundations and the abutment backwalls were modeled as they can exhibit nonlinear behaviors under large loadings. A parametric study is being carried out to investigate the effectiveness of the isolation system for various bridge structures and bearing combinations, and the findings will provide guidance for confirmation and further development of quasi-isolation design strategies.
- 13 April 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 276-288
Computational Analyses of Quasi-Isolated Bridges with Fusing Bearing Components
Computational systems analyses are described for bridge systems that employ quasi-isolation by using a set of fixed bearings in addition to isolation bearings such as elastomeric bearings with an elastomer-concrete sliding interface or elastomeric bearings with a PTFE (Teflon) to stainless steel sliding interface. The system uses stiffened L-shaped retainer brackets that limit transverse displacement of elastomeric bearings and the bridge is intended to respond predictably, reliably, and elastically under service loading (including small seismic events), but for larger seismic events, certain bridge bearing components are intended to "fuse" and experience nonlinear behaviors that can allow for passive quasi-isolation of the bridge superstructure. To facilitate the computational modeling, experimental findings from ongoing research are being used to formulate phenomenological element models that simulate nonlinear fusing behaviors in the bridge bearings and auxiliary components. Furthermore the substructure pier elements, the bridge foundations and the abutment backwalls were modeled as they can exhibit nonlinear behaviors under large loadings. A parametric study is being carried out to investigate the effectiveness of the isolation system for various bridge structures and bearing combinations, and the findings will provide guidance for confirmation and further development of quasi-isolation design strategies.
- 13 April 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 164-178
Seismic Response of Bearings for Quasi-Isolated Bridges—Testing and Component Modeling
In areas of moderate seismicity, such as Mid-America, there is interest in developing alternate bridge design and construction methodologies to the typical approaches that are employed in high-seismic regions. One such method is to design so that various bearing components will exceed their ultimate capacities during a major seismic event in a specific sequence, leading to a global bridge structure response similar to a seismically-isolated system. Because the bridge would typically exhibit a stiff response, only developing an isolated response during major earthquakes, the bridge superstructure response may be described as quasi-isolated. This paper presents results for elastomeric bearing components obtained for an experimental program performed to investigate and characterize various bearing types that are being used for quasi-isolated designs. The elastomeric bearings investigated displayed approximately linear elastic response before sliding with a friction coefficient in the range of 0.3 – 0.45, at a shear strain in the range of 150 – 250%. The experiments also investigated the response of anchored retainer brackets used to prevent transverse motion for service loads and small earthquakes to characterize the combined effects of shear and overturning up to and including rupture of the concrete anchor. The test data indicate that the required horizontal force delivered by a bearing to a retainer to cause a failure of the anchor is slightly higher than the ultimate pure tensile strength of the anchor.
- 13 April 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 164-178
Seismic Response of Bearings for Quasi-Isolated Bridges—Testing and Component Modeling
In areas of moderate seismicity, such as Mid-America, there is interest in developing alternate bridge design and construction methodologies to the typical approaches that are employed in high-seismic regions. One such method is to design so that various bearing components will exceed their ultimate capacities during a major seismic event in a specific sequence, leading to a global bridge structure response similar to a seismically-isolated system. Because the bridge would typically exhibit a stiff response, only developing an isolated response during major earthquakes, the bridge superstructure response may be described as quasi-isolated. This paper presents results for elastomeric bearing components obtained for an experimental program performed to investigate and characterize various bearing types that are being used for quasi-isolated designs. The elastomeric bearings investigated displayed approximately linear elastic response before sliding with a friction coefficient in the range of 0.3 – 0.45, at a shear strain in the range of 150 – 250%. The experiments also investigated the response of anchored retainer brackets used to prevent transverse motion for service loads and small earthquakes to characterize the combined effects of shear and overturning up to and including rupture of the concrete anchor. The test data indicate that the required horizontal force delivered by a bearing to a retainer to cause a failure of the anchor is slightly higher than the ultimate pure tensile strength of the anchor.