Ulrich Meier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ulrich Meier has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
J. Heinze
4 shared publicationsC. Hassa
DLR - German Aerospace Center, Institute of Propulsion Technology, Linder Hoehe, Cologne D-51147, Germany
2 shared publications- Christian Willert
DLR Institute of Propulsion Technology, German Aerospace Center, Köln, Germany
2 shared publications - Christoph Hassa
Institute of Propulsion Technology, German Aerospace Center (DLR), 51147 Cologne, Germany
2 shared publications - Guido Stockhausen
DLR—German Aerospace Center, Institute of Propulsion Technology, Linder Hoehe, Cologne 51147, Germany
2 shared publications - Imon Bagchi
Rolls-Royce Deutschland Ltd & Co KG, Eschenweg 11, Dahlewitz, Blankenfelde-Mahlow 15827, Germany
2 shared publications
Latest Publications
- 20 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2) , 021507
Temperature Measurements at the Outlet of a Lean Burn Single-Sector Combustor by Laser Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Spatially resolved temperatures were measured at different operating conditions using planar laser-induced fluorescence of OH (OH-PLIF) and filtered Rayleigh scattering (FRS), the latter being used in a combustor environment for the first time. Apart from a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its feasibility for future application in a full annular combustor with restricted optical access. Both techniques are complementary in several respects, which justified their combined application. OH-PLIF allows instantaneous measurements and therefore enables local temperature statistics, but is limited to relatively high temperatures. On the other hand, FRS can also be applied at low temperatures, which makes it particularly attractive for measurements in cooling layers. However, FRS requires long sampling times and therefore can only provide temporal averages. When applied in combination, the accuracy of both techniques could be improved by each method helping to overcome the other's shortcomings.
- 20 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2) , 021507
Temperature Measurements at the Outlet of a Lean Burn Single-Sector Combustor by Laser Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Spatially resolved temperatures were measured at different operating conditions using planar laser-induced fluorescence of OH (OH-PLIF) and filtered Rayleigh scattering (FRS), the latter being used in a combustor environment for the first time. Apart from a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its feasibility for future application in a full annular combustor with restricted optical access. Both techniques are complementary in several respects, which justified their combined application. OH-PLIF allows instantaneous measurements and therefore enables local temperature statistics, but is limited to relatively high temperatures. On the other hand, FRS can also be applied at low temperatures, which makes it particularly attractive for measurements in cooling layers. However, FRS requires long sampling times and therefore can only provide temporal averages. When applied in combination, the accuracy of both techniques could be improved by each method helping to overcome the other's shortcomings.
- 16 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (1) , 011503
Flow Field Characterization at the Outlet of a Lean Burn Single-Sector Combustor by Laser-Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.
- 16 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (1) , 011503
Flow Field Characterization at the Outlet of a Lean Burn Single-Sector Combustor by Laser-Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.
- 23 September 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (12) , 121508
Characterization of Lean Burn Module Air Blast Pilot Injector With Laser Techniques
For lean burn combustor development in low emission aero-engines, the pilot stage of the fuel injector plays a key role with respect to stability, operability, NOx emissions, and smoke production. Therefore it is of considerable interest to characterize the pilot module in terms of pilot zone mixing, fuel placement, flow field, and interaction with the main stage. This contribution focuses on the investigation of soot formation during pilot-only operation. Optical test methods were applied in an optically accessible single sector rig at engine idle conditions. Using planar laser-induced incandescence (LII), the distribution of soot and its dependence on air/fuel ratio, as well as geometric injector parameters, was studied. The data shows that below a certain air/fuel ratio, an increase of soot production occurs. This is in agreement with smoke number measurements in a standard single sector flame tube rig without optical access. Reaction zones were identified using chemiluminescence of OH radicals. In addition, the injector flow field was investigated with PIV. A hypothesis regarding the mechanism of pilot smoke formation was made based on these findings. This along with further investigations will form the basis for developing strategies for smoke improvement at elevated pilot-only conditions.
- 23 September 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (12) , 121508
Characterization of Lean Burn Module Air Blast Pilot Injector With Laser Techniques
For lean burn combustor development in low emission aero-engines, the pilot stage of the fuel injector plays a key role with respect to stability, operability, NOx emissions, and smoke production. Therefore it is of considerable interest to characterize the pilot module in terms of pilot zone mixing, fuel placement, flow field, and interaction with the main stage. This contribution focuses on the investigation of soot formation during pilot-only operation. Optical test methods were applied in an optically accessible single sector rig at engine idle conditions. Using planar laser-induced incandescence (LII), the distribution of soot and its dependence on air/fuel ratio, as well as geometric injector parameters, was studied. The data shows that below a certain air/fuel ratio, an increase of soot production occurs. This is in agreement with smoke number measurements in a standard single sector flame tube rig without optical access. Reaction zones were identified using chemiluminescence of OH radicals. In addition, the injector flow field was investigated with PIV. A hypothesis regarding the mechanism of pilot smoke formation was made based on these findings. This along with further investigations will form the basis for developing strategies for smoke improvement at elevated pilot-only conditions.
- 20 January 2012
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 3 (1) , 45-53
Characterisation of the combustion performance of low emission fuel injectors with laser measurements
- 20 January 2012
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 3 (1) , 45-53
Characterisation of the combustion performance of low emission fuel injectors with laser measurements
- 1 November 2005
- Published by Optica Publishing Group in Applied Optics
- Vol. 44 (31) , 6565-6577
Phase-locked two-line OH planar laser-induced fluorescence thermometry in a pulsating gas turbine model combustor at atmospheric pressure
Two-line OH planar laser-induced fluorescence (PLIF) thermometry was applied to a swirling CH4/air flame in a gas turbine (GT) model combustor at atmospheric pressure, which exhibited self-excited combustion instability. The potential and limitations of the method are discussed with respect to applications in GT-like flames. A major drawback of using OH as a temperature indicator is that no temperature information can be obtained from regions where OH radicals are missing or present in insufficient concentration. The resulting bias in the average temperature is addressed and quantified for one operating condition by a comparison with results from laser Raman measurements applied in the same flame. Care was taken to minimize saturation effects by decreasing the spectral laser power density to a minimum while keeping an acceptable spatial resolution and signal-to-noise ratio. In order to correct for the influence of laser light attenuation, absorption measurements were performed on a single-shot basis and a correction procedure was applied. The accuracy was determined to 4%–7% depending on the location within the flame and on the temperature level. A GT model combustor with an optical combustion chamber is described, and phase-locked 2D temperature distributions from a pulsating flame are presented. The temperature variations during an oscillation cycle are specified, and the general flame behavior is described. Our main goals are the evaluation of the OH PLIF thermometry and the characterization of a pulsating GT-like flame.
- 1 November 2005
- Published by Optica Publishing Group in Applied Optics
- Vol. 44 (31) , 6565-6577
Phase-locked two-line OH planar laser-induced fluorescence thermometry in a pulsating gas turbine model combustor at atmospheric pressure
Two-line OH planar laser-induced fluorescence (PLIF) thermometry was applied to a swirling CH4/air flame in a gas turbine (GT) model combustor at atmospheric pressure, which exhibited self-excited combustion instability. The potential and limitations of the method are discussed with respect to applications in GT-like flames. A major drawback of using OH as a temperature indicator is that no temperature information can be obtained from regions where OH radicals are missing or present in insufficient concentration. The resulting bias in the average temperature is addressed and quantified for one operating condition by a comparison with results from laser Raman measurements applied in the same flame. Care was taken to minimize saturation effects by decreasing the spectral laser power density to a minimum while keeping an acceptable spatial resolution and signal-to-noise ratio. In order to correct for the influence of laser light attenuation, absorption measurements were performed on a single-shot basis and a correction procedure was applied. The accuracy was determined to 4%–7% depending on the location within the flame and on the temperature level. A GT model combustor with an optical combustion chamber is described, and phase-locked 2D temperature distributions from a pulsating flame are presented. The temperature variations during an oscillation cycle are specified, and the general flame behavior is described. Our main goals are the evaluation of the OH PLIF thermometry and the characterization of a pulsating GT-like flame.
- 20 March 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (9) , 1434-1443
Quantification of NO A–X(0, 2) laser-induced fluorescence: investigation of calibration and collisional influences in high-pressure flames
Laser-induced-fluorescence techniques have been used successfully for quantitative two-dimensional measurements of nitric oxide. NO A–X(0, 2) excitation at 248 nm recently found applications in internal-combustion engines. We assess the collisional processes that influence quantification of signal intensities in terms of saturation, rotational energy transfer, and line broadening, using laminar high-pressure methane/air and n-heptane/air flames at pressures as high as 80 bars (8 × 106 Pa). A calibration method that is applicable in technical combustion systems based on addition of NO to the burning flame is investigated for various air/fuel ratios and pressures and yields information about the influence of NO reburn processes.
- 20 March 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (9) , 1434-1443
Quantification of NO A–X(0, 2) laser-induced fluorescence: investigation of calibration and collisional influences in high-pressure flames
Laser-induced-fluorescence techniques have been used successfully for quantitative two-dimensional measurements of nitric oxide. NO A–X(0, 2) excitation at 248 nm recently found applications in internal-combustion engines. We assess the collisional processes that influence quantification of signal intensities in terms of saturation, rotational energy transfer, and line broadening, using laminar high-pressure methane/air and n-heptane/air flames at pressures as high as 80 bars (8 × 106 Pa). A calibration method that is applicable in technical combustion systems based on addition of NO to the burning flame is investigated for various air/fuel ratios and pressures and yields information about the influence of NO reburn processes.
- 1 May 1997
- Published by Springer Nature in Applied Physics B
- Vol. 64 (5) , 585-591
OH laser-induced fluorescence at high pressures: spectroscopic and two-dimensional measurements exciting the A-X (1,0) transition
- 1 May 1997
- Published by Springer Nature in Applied Physics B
- Vol. 64 (5) , 585-591
OH laser-induced fluorescence at high pressures: spectroscopic and two-dimensional measurements exciting the A-X (1,0) transition
- 1 November 1995
- Published by Springer Nature in Applied Physics B
- Vol. 61 (5) , 409-414
Laser-induced fluorescence thermometry and concentration measurements on NOA?X (0-0) transitions in the exhaust gas of high pressure CH4/air flames
- 1 November 1995
- Published by Springer Nature in Applied Physics B
- Vol. 61 (5) , 409-414
Laser-induced fluorescence thermometry and concentration measurements on NOA?X (0-0) transitions in the exhaust gas of high pressure CH4/air flames