Imon Bagchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Imon Bagchi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Christoph Hassa
Institute of Propulsion Technology, German Aerospace Center (DLR), 51147 Cologne, Germany
2 shared publications - Guido Stockhausen
DLR—German Aerospace Center, Institute of Propulsion Technology, Linder Hoehe, Cologne 51147, Germany
2 shared publications - Ulrich Doll
German Aerospace Center, Cologne, Germany
2 shared publications - Ulrich Meier
DLR—German Aerospace Center, Institute of Propulsion Technology, Linder Hoehe, Cologne 51147, Germany
2 shared publications - Christian Willert
DLR Institute of Propulsion Technology, German Aerospace Center, Köln, Germany
1 shared publication - Johannes Heinze
Institute of Biochemistry and Biology, Biodiversity Research and Systematic Botany, University of Potsdam, Potsdam, Germany
1 shared publication
Latest Publications
- 20 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2) , 021507
Temperature Measurements at the Outlet of a Lean Burn Single-Sector Combustor by Laser Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Spatially resolved temperatures were measured at different operating conditions using planar laser-induced fluorescence of OH (OH-PLIF) and filtered Rayleigh scattering (FRS), the latter being used in a combustor environment for the first time. Apart from a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its feasibility for future application in a full annular combustor with restricted optical access. Both techniques are complementary in several respects, which justified their combined application. OH-PLIF allows instantaneous measurements and therefore enables local temperature statistics, but is limited to relatively high temperatures. On the other hand, FRS can also be applied at low temperatures, which makes it particularly attractive for measurements in cooling layers. However, FRS requires long sampling times and therefore can only provide temporal averages. When applied in combination, the accuracy of both techniques could be improved by each method helping to overcome the other's shortcomings.
- 20 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2) , 021507
Temperature Measurements at the Outlet of a Lean Burn Single-Sector Combustor by Laser Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Spatially resolved temperatures were measured at different operating conditions using planar laser-induced fluorescence of OH (OH-PLIF) and filtered Rayleigh scattering (FRS), the latter being used in a combustor environment for the first time. Apart from a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its feasibility for future application in a full annular combustor with restricted optical access. Both techniques are complementary in several respects, which justified their combined application. OH-PLIF allows instantaneous measurements and therefore enables local temperature statistics, but is limited to relatively high temperatures. On the other hand, FRS can also be applied at low temperatures, which makes it particularly attractive for measurements in cooling layers. However, FRS requires long sampling times and therefore can only provide temporal averages. When applied in combination, the accuracy of both techniques could be improved by each method helping to overcome the other's shortcomings.
- 16 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (1) , 011503
Flow Field Characterization at the Outlet of a Lean Burn Single-Sector Combustor by Laser-Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.
- 16 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (1) , 011503
Flow Field Characterization at the Outlet of a Lean Burn Single-Sector Combustor by Laser-Optical Methods
High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.