Alexey R. Kovsh
Research Subjects
Alexey R. Kovsh has a total of 195 co-authors. Here are the top co-authors by number of shared publications:
- Nikolay N. Ledentsov
VI Systems GmbH, Hardenbergstr 7, 10623 Berlin, Germany
13 shared publications - Alexey E. Zhukov
Russian Academy of Sciences
12 shared publications - Sergey S. Mikhrin
Innolume GmbH (Germany)
12 shared publications D. Bimberg
Technische Univ. Berlin (Germany)
10 shared publications- Yu.M. Shernyakov
Ioffe Institute, St. Petersburg, Russia
9 shared publications - Igor L. Krestnikov
Innolume GmbH
7 shared publications
Latest Publications
- 27 May 2009
- Published by Optica Publishing Group in Optics Letters
- Vol. 34 (11) , 1672-1674
High-power quantum-dot-based semiconductor disk laser
We demonstrate multiwatt cw output power from an optically pumped quantum-dot semiconductor disk laser. Continuous-wave output power of with 22% slope efficiency was demonstrated at a center wavelength of . This represents an increase in power of 15 times and an increase in slope efficiency of 10 times from the previously published results using Stranski–Krastanow grown quantum dots. An intracavity diamond heat spreader was used for thermal management. The maximum output power was limited by the available pump power, and no sign of thermal rollover was observed.- 27 May 2009
- Published by Optica Publishing Group in Optics Letters
- Vol. 34 (11) , 1672-1674
High-power quantum-dot-based semiconductor disk laser
We demonstrate multiwatt cw output power from an optically pumped quantum-dot semiconductor disk laser. Continuous-wave output power of with 22% slope efficiency was demonstrated at a center wavelength of . This represents an increase in power of 15 times and an increase in slope efficiency of 10 times from the previously published results using Stranski–Krastanow grown quantum dots. An intracavity diamond heat spreader was used for thermal management. The maximum output power was limited by the available pump power, and no sign of thermal rollover was observed.- 13 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 679-686
Temperature-Dependent Small-Signal Analysis of High-Speed High-Temperature Stable 980-nm VCSELs
980-nm VCSELs based on submonolayer growth show for 20-Gbit/s large-signal modulation clearly open eyes without adjustment of the driving conditions between 25degC and 120degC. To access the limiting mechanism for the modulation bandwidth, a temperature-dependent small-signal analysis is carried out on these devices. Single-mode devices are limited by damping, whereas multimode devices are limited by thermal effects, preventing higher photon densities in the cavity.
- 13 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 15 (3) , 679-686
Temperature-Dependent Small-Signal Analysis of High-Speed High-Temperature Stable 980-nm VCSELs
980-nm VCSELs based on submonolayer growth show for 20-Gbit/s large-signal modulation clearly open eyes without adjustment of the driving conditions between 25degC and 120degC. To access the limiting mechanism for the modulation bandwidth, a temperature-dependent small-signal analysis is carried out on these devices. Single-mode devices are limited by damping, whereas multimode devices are limited by thermal effects, preventing higher photon densities in the cavity.
- 8 February 2007
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6468, 64681O
Novel concepts for ultrahigh-speed quantum-dot VCSELs and edge-emitters
Advanced types of QD media allow an ultrahigh modal gain, avoid temperature depletion and gain saturation effects, when used in high-speed quantum dot (QD) vertical-cavity surface-emitting lasers (VCSELs). An anti-guiding VCSEL design reduces gain depletion and radiative leakage, caused by parasitic whispering gallery VCSEL modes. Temperature robustness up to 100°C for 0.96 - 1.25 &mgr;m range devices is realized in the continuous wave (cw) regime. An open eye 20 Gb/s operation with bit error rates better than 10-12 has been achieved in a temperature range 25-85°C without current adjustment. A different approach for ultrahigh-speed operation is based on a combination of the VCSEL section, operating in the CW mode with an additional section of the device, which is electrooptically modulated under a reverse bias. The tuning of a resonance wavelength of the second section, caused by the electrooptic effect, affects the transmission of the system. The second cavity mode, resonant to the VCSEL mode, or the stopband edge of the second Bragg reflector can be used for intensity modulation. The approach enables ultrahigh speed signal modulation. 60GHz electrical and ~35GHz optical (limited by the photodetector response) bandwidths are realized.
- 8 February 2007
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6468, 64681O
Novel concepts for ultrahigh-speed quantum-dot VCSELs and edge-emitters
Advanced types of QD media allow an ultrahigh modal gain, avoid temperature depletion and gain saturation effects, when used in high-speed quantum dot (QD) vertical-cavity surface-emitting lasers (VCSELs). An anti-guiding VCSEL design reduces gain depletion and radiative leakage, caused by parasitic whispering gallery VCSEL modes. Temperature robustness up to 100°C for 0.96 - 1.25 &mgr;m range devices is realized in the continuous wave (cw) regime. An open eye 20 Gb/s operation with bit error rates better than 10-12 has been achieved in a temperature range 25-85°C without current adjustment. A different approach for ultrahigh-speed operation is based on a combination of the VCSEL section, operating in the CW mode with an additional section of the device, which is electrooptically modulated under a reverse bias. The tuning of a resonance wavelength of the second section, caused by the electrooptic effect, affects the transmission of the system. The second cavity mode, resonant to the VCSEL mode, or the stopband edge of the second Bragg reflector can be used for intensity modulation. The approach enables ultrahigh speed signal modulation. 60GHz electrical and ~35GHz optical (limited by the photodetector response) bandwidths are realized.
- 13 July 2006
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6350, 635003
20-Gb/s direct modulation of 980 nm VCSELs based on submonolayer deposition of quantum dots
980 nm vertical-cavity surface-emitting laser based on sub-monolayer growth of quantum dots show at 25 and 85°C for 20 Gb/s without current adjustment clearly open eyes and error free operation with bit error rates better than 10-12. For these multimode lasers the small signal modulation bandwidth decreases only from 15 GHz at 25°C to 13 GHz at 85°C. Single mode devices demonstrate at 20°C a small signal modulation bandwidth of 16.6 GHz with 0.8 mW optical output power and a record high modulation current efficiency factor of 19 GHz/mA1/2.
- 13 July 2006
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6350, 635003
20-Gb/s direct modulation of 980 nm VCSELs based on submonolayer deposition of quantum dots
980 nm vertical-cavity surface-emitting laser based on sub-monolayer growth of quantum dots show at 25 and 85°C for 20 Gb/s without current adjustment clearly open eyes and error free operation with bit error rates better than 10-12. For these multimode lasers the small signal modulation bandwidth decreases only from 15 GHz at 25°C to 13 GHz at 85°C. Single mode devices demonstrate at 20°C a small signal modulation bandwidth of 16.6 GHz with 0.8 mW optical output power and a record high modulation current efficiency factor of 19 GHz/mA1/2.
- 5 July 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 18 (14) , 1500-1502
Stable mode-locked operation up to 80 /spl deg/C from an InGaAs quantum-dot laser
We demonstrate the mode-locked operation of a two-section quantum-dot laser in a broad temperature range. Stable mode-locking was observed at temperatures ranging from 20 /spl deg/C to 70 /spl deg/C, with signal-to-noise ratios well over 20 dB and a -3-dB linewidth smaller than 80 kHz. In the temperature range between 70 /spl deg/C and 80 /spl deg/C, the mode-locking was less stable. It was found that in order to provide stable mode-locked operation with increasing temperature, the reverse bias on the absorber section must be reduced accordingly.
- 5 July 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 18 (14) , 1500-1502
Stable mode-locked operation up to 80 /spl deg/C from an InGaAs quantum-dot laser
We demonstrate the mode-locked operation of a two-section quantum-dot laser in a broad temperature range. Stable mode-locking was observed at temperatures ranging from 20 /spl deg/C to 70 /spl deg/C, with signal-to-noise ratios well over 20 dB and a -3-dB linewidth smaller than 80 kHz. In the temperature range between 70 /spl deg/C and 80 /spl deg/C, the mode-locking was less stable. It was found that in order to provide stable mode-locked operation with increasing temperature, the reverse bias on the absorber section must be reduced accordingly.
- 25 August 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 64
Vertically Coupled Quantum Dot Injection Laser Grown on InP
- 25 August 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 64
Vertically Coupled Quantum Dot Injection Laser Grown on InP
- 28 April 2005
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5722, 130-147
Edge and surface-emitting tilted cavity lasers (Invited Paper)
The Tilted Cavity (TC) concept has been proposed to combine advantages of edge- and surface-emitting lasers (detectors, amplifiers, switches, etc.). Tilted Cavity Lasers (TCL) enable wavelength-stabilized high-power edge and surface emitters (TCSEL) in low-cost single-epitaxial step design. The concept covers numerous applications including mode-locked TCL for light speed control, dispersion and linewidth engineering, GaN-based light-emitters, electrooptic wavelength tunable devices, and other applications. Presently, wavelength stabilized TC operation is realized between -200°C and 70°C in broad TCL diodes with cleaved facets based on quantum dots (QDs). The spectral width is below 0.6 nm in broad area 100 μm-wide-stipe devices. The far fields are: 4° (lateral) and 42° (vertical). Wavelength-stabilized 1.16 μm and 1.27 μm edge-emitting QD TCL lasers are demonstrated. Quantum well TCL demonstrate high-temperature operation up to 240°C with a low threshold, high temperature stability and improved wavelength stability. The tilted cavity approach can also be applied in wavelength-optimized photodetectors, switches, semiconductor optical amplifiers, including multi-channel devices, in optical fibers, in photodetectors, in light-emitting diodes and in many other applications. Moreover, microelectronic devices based on similar tilted angle resonance phenomena in quantum wells and superlattices can be realized in electron- or hole-wavefunction-engineered structures, thus, merging the fields of nanophotonics and nanoelectronics. The tilted cavity concept can be further complimented by lateral patterning and (or) processing of three-dimensional photonic crystal structures further extending horizons of modern optoelectronics.
- 28 April 2005
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5722, 130-147
Edge and surface-emitting tilted cavity lasers (Invited Paper)
The Tilted Cavity (TC) concept has been proposed to combine advantages of edge- and surface-emitting lasers (detectors, amplifiers, switches, etc.). Tilted Cavity Lasers (TCL) enable wavelength-stabilized high-power edge and surface emitters (TCSEL) in low-cost single-epitaxial step design. The concept covers numerous applications including mode-locked TCL for light speed control, dispersion and linewidth engineering, GaN-based light-emitters, electrooptic wavelength tunable devices, and other applications. Presently, wavelength stabilized TC operation is realized between -200°C and 70°C in broad TCL diodes with cleaved facets based on quantum dots (QDs). The spectral width is below 0.6 nm in broad area 100 μm-wide-stipe devices. The far fields are: 4° (lateral) and 42° (vertical). Wavelength-stabilized 1.16 μm and 1.27 μm edge-emitting QD TCL lasers are demonstrated. Quantum well TCL demonstrate high-temperature operation up to 240°C with a low threshold, high temperature stability and improved wavelength stability. The tilted cavity approach can also be applied in wavelength-optimized photodetectors, switches, semiconductor optical amplifiers, including multi-channel devices, in optical fibers, in photodetectors, in light-emitting diodes and in many other applications. Moreover, microelectronic devices based on similar tilted angle resonance phenomena in quantum wells and superlattices can be realized in electron- or hole-wavefunction-engineered structures, thus, merging the fields of nanophotonics and nanoelectronics. The tilted cavity concept can be further complimented by lateral patterning and (or) processing of three-dimensional photonic crystal structures further extending horizons of modern optoelectronics.
- 22 February 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 51-52
Mode-locking at 9.7 GHz repetition rate with 1.7 ps pulse duration in two-section QD lasers
Ultrashort pulses of 1.7 ps at frequency as low as 9.7 GHz are demonstrated by passive mode-locking of monolithic two-section InAs/InGaAs (/spl lambda/=1.28 /spl mu/m) quantum-dot laser. Pulse shortening with the absorber section bias increase is observed.
- 22 February 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 51-52
Mode-locking at 9.7 GHz repetition rate with 1.7 ps pulse duration in two-section QD lasers
Ultrashort pulses of 1.7 ps at frequency as low as 9.7 GHz are demonstrated by passive mode-locking of monolithic two-section InAs/InGaAs (/spl lambda/=1.28 /spl mu/m) quantum-dot laser. Pulse shortening with the absorber section bias increase is observed.
- 1 January 2005
- Published by Institution of Engineering and Technology (IET)
- p. v2:165
High-power, high repetition rate, short-pulse mode-locking using flared waveguide quantum-dot lasers at 1.3 μm
Ultra-short pulse, high power mode-locking is demonstrated in InGaAs quantum dot lasers using a flared waveguide design. 24 GHz mode-locking with 790 fs wide pulses and 500 mW peak powers suitable for telecommunications applications are presented. (2 pages)
- 1 January 2005
- Published by Institution of Engineering and Technology (IET)
- p. v2:165
High-power, high repetition rate, short-pulse mode-locking using flared waveguide quantum-dot lasers at 1.3 μm
Ultra-short pulse, high power mode-locking is demonstrated in InGaAs quantum dot lasers using a flared waveguide design. 24 GHz mode-locking with 790 fs wide pulses and 500 mW peak powers suitable for telecommunications applications are presented. (2 pages)
- 23 December 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 156-157 vol.1
Characteristics of high-performance 1.0 μm and 1.3 μm quantum dot lasers: impact of p-doping and tunnel injection
There is a need to understand the performance limitations and the role of special techniques to enhance quantum dot (QD) laser performance. In this context, we have examined the role of p-doping in the dots and tunnel injection of electrons into the active dots in the lasers. Utilizing these techniques, we demonstrate QD lasers with zero temperature dependence of the threshold current (T/sub 0/=/spl infin/) and the output slope efficiency and small signal modulation bandwidth /spl cong/25 GHz. It is apparent that an optimal level of p-doping, combined with tunnel injection, will lead to lasers with high modulation bandwidth, zero chirp and very high T/sub 0/. These results are presented and discussed.
- 23 December 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 156-157 vol.1
Characteristics of high-performance 1.0 μm and 1.3 μm quantum dot lasers: impact of p-doping and tunnel injection
There is a need to understand the performance limitations and the role of special techniques to enhance quantum dot (QD) laser performance. In this context, we have examined the role of p-doping in the dots and tunnel injection of electrons into the active dots in the lasers. Utilizing these techniques, we demonstrate QD lasers with zero temperature dependence of the threshold current (T/sub 0/=/spl infin/) and the output slope efficiency and small signal modulation bandwidth /spl cong/25 GHz. It is apparent that an optimal level of p-doping, combined with tunnel injection, will lead to lasers with high modulation bandwidth, zero chirp and very high T/sub 0/. These results are presented and discussed.