Seungsuk Oh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seungsuk Oh has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Myoungho Sunwoo
Department of Automotive Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 04763, Korea
2 shared publications - Byounggul Oh
Department of Automotive Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791, Republic of Korea
1 shared publication - Jeasung Chung
Department of Automotive Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 133-791, Korea
1 shared publication - Jongsuk Lim
Department of Automotive Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 133-791, Korea
1 shared publication - Junsoo Kim
Department of Automotive Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791, Republic of Korea
1 shared publication - Kangyoon Lee
Department of Automotive Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791, Republic of Korea
1 shared publication
Latest Publications
- 11 June 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (8) , 082801
Real-Time Combustion Phase Detection Using Central Normalized Difference Pressure in CRDI Diesel Engines
To develop eco-friendly diesel engines, accurate combustion phase control is important due to its significant effects on harmful emissions and fuel efficiency. In order to accurately control the combustion phase, the detection of the combustion phase should precede control system design. Currently, combustion phase detection is done by the location of 50% mass fraction burned (MFB50), because of its close correlation with emissions and fuel efficiency. However, this method is not easily implemented in real-time applications because the calculation of MFB50 requires a large amount of in-cylinder pressure data and an excessive computational load. For this reason, a combustion phase indicator with a simple algorithm is required for real-time combustion control. In this study, we propose a new combustion phase indicator, called the “Central normalized difference pressures (CNDP).” The CNDP indicates the center of the two crank angles where the normalized difference pressure between firing pressure and motoring pressure (NDP) reaches 90% of the maximum value before peak (NDPbp90), and 70% of the maximum value after peak (NDPap70). The NDPbp90 and NDPap70 are highly correlated with MFB50 and the correlation is enhanced as the center between the two points obtained. The CNDP is represented by a fixed quadratic polynomial with MFB50 that robust to changes in various engine operating conditions such as engine speed, main injection timing, injected fuel quantity, fuel-rail pressure, exhaust gas recirculation (EGR) rate and boost pressure. Furthermore, in performance evaluation, the CNDP requires remarkably fewer in-cylinder pressure data samples, calculation steps and less computation time compared to MFB50. These results show great potential for the CNDP to be a substitute for the MFB50 since the proposed combustion phase detection algorithm can be used effectively for real-time combustion phase detection and control.
- 11 June 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (8) , 082801
Real-Time Combustion Phase Detection Using Central Normalized Difference Pressure in CRDI Diesel Engines
To develop eco-friendly diesel engines, accurate combustion phase control is important due to its significant effects on harmful emissions and fuel efficiency. In order to accurately control the combustion phase, the detection of the combustion phase should precede control system design. Currently, combustion phase detection is done by the location of 50% mass fraction burned (MFB50), because of its close correlation with emissions and fuel efficiency. However, this method is not easily implemented in real-time applications because the calculation of MFB50 requires a large amount of in-cylinder pressure data and an excessive computational load. For this reason, a combustion phase indicator with a simple algorithm is required for real-time combustion control. In this study, we propose a new combustion phase indicator, called the “Central normalized difference pressures (CNDP).” The CNDP indicates the center of the two crank angles where the normalized difference pressure between firing pressure and motoring pressure (NDP) reaches 90% of the maximum value before peak (NDPbp90), and 70% of the maximum value after peak (NDPap70). The NDPbp90 and NDPap70 are highly correlated with MFB50 and the correlation is enhanced as the center between the two points obtained. The CNDP is represented by a fixed quadratic polynomial with MFB50 that robust to changes in various engine operating conditions such as engine speed, main injection timing, injected fuel quantity, fuel-rail pressure, exhaust gas recirculation (EGR) rate and boost pressure. Furthermore, in performance evaluation, the CNDP requires remarkably fewer in-cylinder pressure data samples, calculation steps and less computation time compared to MFB50. These results show great potential for the CNDP to be a substitute for the MFB50 since the proposed combustion phase detection algorithm can be used effectively for real-time combustion phase detection and control.
- 14 February 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (6) , 062801
Real-Time IMEP Estimation and Control Using an In-Cylinder Pressure Sensor for a Common-Rail Direct Injection Diesel Engine
An in-cylinder pressure-based control method is capable of improving engine performance, as well as reducing harmful emissions. However, this method is difficult to be implemented in a conventional engine management system due to the excessive data acquisition and long computation time. In this study, we propose a real-time indicated mean effective pressure (IMEP) estimation method using cylinder pressure in a common-rail direct injection diesel engine. In this method, difference pressure integral (DPI) was applied to the estimation. The DPI requires only 180 pressure data points during one engine cycle from top dead center to bottom dead center when pressure data are captured at every crank angle. Therefore, the IMEP can be estimated in real time. To further reduce the computational load, the IMEP was also estimated using DPI at 2 deg, 3 deg, and 4 deg crank angle resolutions. Furthermore, based on the estimated IMEP, we controlled IMEP using a radial basis function network and linear feedback controller. As a result of the study, successful estimation and control were demonstrated through engine experiments.
- 14 February 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (6) , 062801
Real-Time IMEP Estimation and Control Using an In-Cylinder Pressure Sensor for a Common-Rail Direct Injection Diesel Engine
An in-cylinder pressure-based control method is capable of improving engine performance, as well as reducing harmful emissions. However, this method is difficult to be implemented in a conventional engine management system due to the excessive data acquisition and long computation time. In this study, we propose a real-time indicated mean effective pressure (IMEP) estimation method using cylinder pressure in a common-rail direct injection diesel engine. In this method, difference pressure integral (DPI) was applied to the estimation. The DPI requires only 180 pressure data points during one engine cycle from top dead center to bottom dead center when pressure data are captured at every crank angle. Therefore, the IMEP can be estimated in real time. To further reduce the computational load, the IMEP was also estimated using DPI at 2 deg, 3 deg, and 4 deg crank angle resolutions. Furthermore, based on the estimated IMEP, we controlled IMEP using a radial basis function network and linear feedback controller. As a result of the study, successful estimation and control were demonstrated through engine experiments.