John Richard Thome
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
John Richard Thome has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Gherhardt Ribatski
Heat Transfer Research Group, Department of Mechanical Engineering, Sao Carlos School of Engineering, University of São Paulo, São Carlos, Brazil
5 shared publications - Jackson Braz Marcinichen
Laboratory of Heat and Mass Transfer, École Polytechnique Fédérale de Lausanne, EPFL-STI-IGM-LTCM, Station 9, Lausanne CH-1015, Switzerland
3 shared publications - Lixin Cheng
Beijing Key Laboratory of Heat Transfer and Energy Conversion, Beijing University of Technology, Beijing, China
3 shared publications - Stefano Nebuloni
Swiss Federal Institute of Technology Lausanne, Lausanne, Switzerland
3 shared publications - A. K. Das
Department of Mechanical Engineering, IIT Kharagpur, 721302, India
2 shared publications D. Gstoehl
Laboratory of Heat and Mass Transfer, Faculty of Engineering Sciences and Techniques, Ecole Polytechnique Fédérale de Lausanne, CH-1015 Lausanne, Switzerland
2 shared publications
Latest Publications
- Open Access
- 29 November 2019
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (1)
Professor Masahiro Kawaji on His 65th Birthday
This is no abstract because this article is about "Professor Masahiro Kawaji on His 65th Birthday"
- 29 November 2019
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (1)
Open AccessProfessor Masahiro Kawaji on His 65th Birthday
This is no abstract because this article is about "Professor Masahiro Kawaji on His 65th Birthday"
- 1 March 2018
- Published by ASME International in Journal of Electronic Packaging
- Vol. 140 (1)
Role of a Liquid Accumulator in a Passive Two-Phase Liquid Cooling System for Electronics: Experimental Analysis
Gravity-driven two-phase liquid cooling systems using flow boiling within microscale evaporators are becoming a game-changing solution for electronics cooling. The optimization of the system's filling ratio (FR) can however become a challenging problem for a system operating over a wide range of cooling capacities and temperature ranges. The benefits of a liquid accumulator (LA) to overcome this difficulty are evaluated in the present paper. An experimental thermosyphon cooling system was built to cool multiple electronic components up to a power dissipation of 1800 W. A double-ended cylinder with a volume of 150 cm3 is evaluated as the LA for two different system volumes (associated with two different condensers). Results demonstrated that the LA provided robust thermal performance as a function of FR for the entire range of heat loads tested. In addition, the present LA was more effective for a small volume system, 599 cm3, than for a large volume system, 1169 cm3, in which the relative size of the LA increased from 12.8% to 25% of the total system's volume.
- 1 March 2018
- Published by ASME International in Journal of Electronic Packaging
- Vol. 140 (1)
Role of a Liquid Accumulator in a Passive Two-Phase Liquid Cooling System for Electronics: Experimental Analysis
Gravity-driven two-phase liquid cooling systems using flow boiling within microscale evaporators are becoming a game-changing solution for electronics cooling. The optimization of the system's filling ratio (FR) can however become a challenging problem for a system operating over a wide range of cooling capacities and temperature ranges. The benefits of a liquid accumulator (LA) to overcome this difficulty are evaluated in the present paper. An experimental thermosyphon cooling system was built to cool multiple electronic components up to a power dissipation of 1800 W. A double-ended cylinder with a volume of 150 cm3 is evaluated as the LA for two different system volumes (associated with two different condensers). Results demonstrated that the LA provided robust thermal performance as a function of FR for the entire range of heat loads tested. In addition, the present LA was more effective for a small volume system, 599 cm3, than for a large volume system, 1169 cm3, in which the relative size of the LA increased from 12.8% to 25% of the total system's volume.
- 10 July 2017
- Published by ASME International in Journal of Electronic Packaging
- Vol. 139 (3) , 031008
Flow Boiling Heat Transfer and Pressure Drops of R1234ze(E) in a Silicon Micro-pin Fin Evaporator
The development of newer and more efficient cooling techniques to sustain the increasing power density of high-performance computing systems is becoming one of the major challenges in the development of microelectronics. In this framework, two-phase cooling is a promising solution for dissipating the greater amount of generated heat. In the present study, an experimental investigation of two-phase flow boiling in a micro-pin fin evaporator is performed. The micro-evaporator has a heated area of 1 cm2 containing 66 rows of cylindrical in-line micro-pin fins with diameter, height, and pitch of, respectively, 50 μm, 100 μm, and 91.7 μm. The working fluid is R1234ze(E) tested over a wide range of conditions: mass fluxes varying from 750 kg/m2 s to 1750 kg/m2 s and heat fluxes ranging from 20 W/cm2 to 44 W/cm2. The effects of saturation temperature on the heat transfer are investigated by testing three different outlet saturation temperatures: 25 °C, 30 °C, and 35 °C. In order to assess the thermal–hydraulic performance of the current heat sink, the total pressure drops are directly measured, while local values of heat transfer coefficient are evaluated by coupling high-speed flow visualization with infrared temperature measurements. According to the experimental results, the mass flux has the most significant impact on the heat transfer coefficient while heat flux is a less influential parameter. The vapor quality varies in a range between 0 and 0.45. The heat transfer coefficient in the subcooled region reaches a maximum value of about 12 kW/m2 K, whilst in two-phase flow it goes up to 30 kW/m2 K.
- 10 July 2017
- Published by ASME International in Journal of Electronic Packaging
- Vol. 139 (3) , 031008
Flow Boiling Heat Transfer and Pressure Drops of R1234ze(E) in a Silicon Micro-pin Fin Evaporator
The development of newer and more efficient cooling techniques to sustain the increasing power density of high-performance computing systems is becoming one of the major challenges in the development of microelectronics. In this framework, two-phase cooling is a promising solution for dissipating the greater amount of generated heat. In the present study, an experimental investigation of two-phase flow boiling in a micro-pin fin evaporator is performed. The micro-evaporator has a heated area of 1 cm2 containing 66 rows of cylindrical in-line micro-pin fins with diameter, height, and pitch of, respectively, 50 μm, 100 μm, and 91.7 μm. The working fluid is R1234ze(E) tested over a wide range of conditions: mass fluxes varying from 750 kg/m2 s to 1750 kg/m2 s and heat fluxes ranging from 20 W/cm2 to 44 W/cm2. The effects of saturation temperature on the heat transfer are investigated by testing three different outlet saturation temperatures: 25 °C, 30 °C, and 35 °C. In order to assess the thermal–hydraulic performance of the current heat sink, the total pressure drops are directly measured, while local values of heat transfer coefficient are evaluated by coupling high-speed flow visualization with infrared temperature measurements. According to the experimental results, the mass flux has the most significant impact on the heat transfer coefficient while heat flux is a less influential parameter. The vapor quality varies in a range between 0 and 0.45. The heat transfer coefficient in the subcooled region reaches a maximum value of about 12 kW/m2 K, whilst in two-phase flow it goes up to 30 kW/m2 K.
- 1 March 2016
- Published by ASME International in Journal of Electronic Packaging
- Vol. 138 (1) , 010901
Dynamic Numerical Microchannel Evaporator Model to Investigate Parallel Channel Instabilities
A fully dynamic model of a microchannel evaporator is presented. The aim of the model is to study the highly dynamic parallel channel instabilities that occur in these evaporators in more detail. The numerical solver for the model is custom-built and the majority of the paper is focused on detailing the various aspects of this solver. The one-dimensional homogeneous two-phase flow conservation equations are solved to simulate the flow. The full three-dimensional (3D) conduction domain of the evaporator is also dynamically resolved. This allows for the correct simulation of the complex hydraulic and thermal interactions between the microchannels that give rise to the parallel channel instabilities. The model uses state-of-the-art correlations to calculate the frictional pressure losses and heat transfer in the microchannels. In addition, a model for inlet restrictions is also included to simulate the stabilizing effect of these components. In the final part of the paper, validation results of the model are presented, in which the stability results of the model are compared with the existing experimental data from the literature. Next, a parametric study is performed focusing on the stabilizing effects of the solid substrate properties. It is found that increasing the thermal conductivity and thickness of the solid substrate has a strong stabilizing effect, while increasing the number of microchannels has a small destabilizing effect. Finally, representative dynamic results are also given to demonstrate some of the unique capabilities of the model.
- 1 March 2016
- Published by ASME International in Journal of Electronic Packaging
- Vol. 138 (1) , 010901
Dynamic Numerical Microchannel Evaporator Model to Investigate Parallel Channel Instabilities
A fully dynamic model of a microchannel evaporator is presented. The aim of the model is to study the highly dynamic parallel channel instabilities that occur in these evaporators in more detail. The numerical solver for the model is custom-built and the majority of the paper is focused on detailing the various aspects of this solver. The one-dimensional homogeneous two-phase flow conservation equations are solved to simulate the flow. The full three-dimensional (3D) conduction domain of the evaporator is also dynamically resolved. This allows for the correct simulation of the complex hydraulic and thermal interactions between the microchannels that give rise to the parallel channel instabilities. The model uses state-of-the-art correlations to calculate the frictional pressure losses and heat transfer in the microchannels. In addition, a model for inlet restrictions is also included to simulate the stabilizing effect of these components. In the final part of the paper, validation results of the model are presented, in which the stability results of the model are compared with the existing experimental data from the literature. Next, a parametric study is performed focusing on the stabilizing effects of the solid substrate properties. It is found that increasing the thermal conductivity and thickness of the solid substrate has a strong stabilizing effect, while increasing the number of microchannels has a small destabilizing effect. Finally, representative dynamic results are also given to demonstrate some of the unique capabilities of the model.
- 2 September 2015
- Published by Wiley in Journal of Heat Transfer
- Vol. 138 (2) , 021502
Computational Study of Saturated Flow Boiling Within a Microchannel in the Slug Flow Regime
This paper presents a fundamental study of the flow dynamics and heat transfer induced by a slug flow under saturated flow boiling in a circular microchannel. Numerical simulations are carried out by utilizing the commercial CFD solver ansys fluent v. 14.5, with its built-in volume of fluid (VOF) method to advect the interface, which was improved here by implementing self-developed functions to model the phase change and the surface tension force. A continuous stream of bubbles is generated (by additional user-defined functions) by patching vapor bubbles at the channel upstream with a constant generation frequency. This modeling framework can capture the essential features of heat transfer in slug flows for a continuous stream of bubbles which are here investigated in detail, e.g., the mutual influence among the growing bubbles, the fluid mechanics in the liquid slug trapped between two consecutive bubbles, the effect of bubble acceleration on the thickness of the thin liquid film trapped against the channel wall and on other bubbles, and the transient growth of the heat transfer coefficient and then its periodic variation at the terminal steady-periodic regime, which is reached after the transit of a few bubble–liquid slug pairs. Furthermore, the results for a continuous stream of bubbles are found to be quite different than that of a single bubble, emphasizing the importance of modeling multiple bubbles to study this process. Finally, the outcomes of this analysis are utilized to advance a theoretical model for heat transfer in microchannel slug flow that best reproduces the present simulation data.
- 2 September 2015
- Published by Wiley in Journal of Heat Transfer
- Vol. 138 (2) , 021502
Computational Study of Saturated Flow Boiling Within a Microchannel in the Slug Flow Regime
This paper presents a fundamental study of the flow dynamics and heat transfer induced by a slug flow under saturated flow boiling in a circular microchannel. Numerical simulations are carried out by utilizing the commercial CFD solver ansys fluent v. 14.5, with its built-in volume of fluid (VOF) method to advect the interface, which was improved here by implementing self-developed functions to model the phase change and the surface tension force. A continuous stream of bubbles is generated (by additional user-defined functions) by patching vapor bubbles at the channel upstream with a constant generation frequency. This modeling framework can capture the essential features of heat transfer in slug flows for a continuous stream of bubbles which are here investigated in detail, e.g., the mutual influence among the growing bubbles, the fluid mechanics in the liquid slug trapped between two consecutive bubbles, the effect of bubble acceleration on the thickness of the thin liquid film trapped against the channel wall and on other bubbles, and the transient growth of the heat transfer coefficient and then its periodic variation at the terminal steady-periodic regime, which is reached after the transit of a few bubble–liquid slug pairs. Furthermore, the results for a continuous stream of bubbles are found to be quite different than that of a single bubble, emphasizing the importance of modeling multiple bubbles to study this process. Finally, the outcomes of this analysis are utilized to advance a theoretical model for heat transfer in microchannel slug flow that best reproduces the present simulation data.
- Open Access
- 29 April 2014
- Published by ASME International in Journal of Electronic Packaging
- Vol. 136 (2) , 021006
Modeling of Two-Phase Evaporative Heat Transfer in Three-Dimensional Multicavity High Performance Microprocessor Chip Stacks
Three-dimensional (3D) stacking of integrated-circuit (IC) dies increases system density and package functionality by vertically integrating two or more dies with area-array through-silicon-vias (TSVs). This reduces the length of global interconnects and the signal delay time and allows improvements in energy efficiency. However, the accumulation of heat fluxes and thermal interface resistances is a major limitation of vertically integrated packages. Scalable cooling solutions, such as two-phase interlayer cooling, will be required to extend 3D stacks beyond the most modest numbers of dies. This paper introduces a realistic 3D chip stack along with a simulation method for the heat spreading and flow distribution among the channels of the evaporators. The model includes the significant sensitivity of each channel's friction factor to vapor quality, and hence mass flow to heat flux, which characterizes parallel two-phase flows. Simulation cases explore various placements of hot spots within the stack and effects which are unique to two-phase interlayer cooling. The results show that the effect of hot spots on individual dies can be mitigated by strong interlayer heat conduction if the relative position of the hot spots is selected carefully to result in a heat load and flow which are well balanced laterally.
- 29 April 2014
- Published by ASME International in Journal of Electronic Packaging
- Vol. 136 (2) , 021006
Open AccessModeling of Two-Phase Evaporative Heat Transfer in Three-Dimensional Multicavity High Performance Microprocessor Chip Stacks
Three-dimensional (3D) stacking of integrated-circuit (IC) dies increases system density and package functionality by vertically integrating two or more dies with area-array through-silicon-vias (TSVs). This reduces the length of global interconnects and the signal delay time and allows improvements in energy efficiency. However, the accumulation of heat fluxes and thermal interface resistances is a major limitation of vertically integrated packages. Scalable cooling solutions, such as two-phase interlayer cooling, will be required to extend 3D stacks beyond the most modest numbers of dies. This paper introduces a realistic 3D chip stack along with a simulation method for the heat spreading and flow distribution among the channels of the evaporators. The model includes the significant sensitivity of each channel's friction factor to vapor quality, and hence mass flow to heat flux, which characterizes parallel two-phase flows. Simulation cases explore various placements of hot spots within the stack and effects which are unique to two-phase interlayer cooling. The results show that the effect of hot spots on individual dies can be mitigated by strong interlayer heat conduction if the relative position of the hot spots is selected carefully to result in a heat load and flow which are well balanced laterally.
- 8 January 2014
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 17 (3) , 561-572
Sudden expansions in circular microchannels: flow dynamics and pressure drop
- 8 January 2014
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 17 (3) , 561-572
Sudden expansions in circular microchannels: flow dynamics and pressure drop
- 30 September 2012
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 55 (19-20) , 5378
Erratum to “New prediction methods for CO2 evaporation inside tubes: Part I – A two-phase flow pattern map and a flow pattern based phenomenological model for two-phase flow frictional pressure drops” [Int. J. Heat Mass Transfer 51 (1–2) (2008) 111–124]
- 30 September 2012
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 55 (19-20) , 5378
Erratum to “New prediction methods for CO2 evaporation inside tubes: Part I – A two-phase flow pattern map and a flow pattern based phenomenological model for two-phase flow frictional pressure drops” [Int. J. Heat Mass Transfer 51 (1–2) (2008) 111–124]
- 15 February 2012
- Published by Springer Nature
- p. 513-567
Two-Phase On-Chip Cooling Systems for Green Data Centers
- 15 February 2012
- Published by Springer Nature
- p. 513-567
Two-Phase On-Chip Cooling Systems for Green Data Centers
- 19 December 2011
- Published by Wiley in Journal of Heat Transfer
- Vol. 134 (2) , 020906
Flow Boiling Characteristics for R1234ze(E) in 1.0 and 2.2 mm Circular Channels
Experimental flow boiling heat transfer results are presented for horizontal 1.0 and 2.2 mm I.D. (internal diameter) stainless steel tubes for tests with R1234ze(E), a new refrigerant developed as a substitute for R134a with a much lower global warming potential (GWP). The experiments were performed for these two tube diameters in order to investigate a possible transition between macro and microscale flow boiling behavior. The experimental campaign includes mass velocities ranging from 50 to 1500 kg/m2 s, heat fluxes from 10 to 300 kW/m2, exit saturation temperatures of 25, 31 and 35 °C, vapor qualities from 0.05 to 0.99 and heated lengths of 180 mm and 361 mm. Flow pattern characterization was performed using high speed videos. Heat transfer coefficient, critical heat flux and flow pattern data were obtained. R1234ze(E) demonstrated similar thermal performance to R134a data when running at similar conditions.
- 19 December 2011
- Published by Wiley in Journal of Heat Transfer
- Vol. 134 (2) , 020906
Flow Boiling Characteristics for R1234ze(E) in 1.0 and 2.2 mm Circular Channels
Experimental flow boiling heat transfer results are presented for horizontal 1.0 and 2.2 mm I.D. (internal diameter) stainless steel tubes for tests with R1234ze(E), a new refrigerant developed as a substitute for R134a with a much lower global warming potential (GWP). The experiments were performed for these two tube diameters in order to investigate a possible transition between macro and microscale flow boiling behavior. The experimental campaign includes mass velocities ranging from 50 to 1500 kg/m2 s, heat fluxes from 10 to 300 kW/m2, exit saturation temperatures of 25, 31 and 35 °C, vapor qualities from 0.05 to 0.99 and heated lengths of 180 mm and 361 mm. Flow pattern characterization was performed using high speed videos. Heat transfer coefficient, critical heat flux and flow pattern data were obtained. R1234ze(E) demonstrated similar thermal performance to R134a data when running at similar conditions.