N. A. Maleev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
N. A. Maleev has a total of 169 co-authors. Here are the top co-authors by number of shared publications:
- Mikhail A. Bobrov
Ioffe Institute, Saint Petersburg, Russia
24 shared publications - Alexander Kuzmenkov
Физико-технический институт им. А.Ф. Иоффе РАН, Санкт-Петербург, Россия
23 shared publications - Kirill O. Voropaev
АО «ОКБ-Планета», Великий Новгород, Россия
14 shared publications - Leonid Ya. Karachinsky
ITMO University
14 shared publications - Andrey G. Gladyshev
ITMO University
13 shared publications С.а. Блохин
Физико-технический институт им. А.Ф. Иоффе РАН, Санкт-Петербург, Россия
13 shared publications
Latest Publications
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S215-S218
Mushroom Mesa Structure for InAlAs–InGaAs Avalanche Photodiodes
Mushroom mesa structure for InAlAs/InGaAs avalanche photodiodes (APD) was proposed and investigated. APD heterostructrures were grown by molecular-beam epitaxy. Fabricated APDs with the sensitive area diameter of about 30 micron were passivated by SiN deposition and demonstrated avalanche breakdown voltage Vbr 70–80 V. At the applied bias of 0.9 Vbr, the dark current was 75–200 nA. The single-mode coupled APDs demonstrated responsivity at a gain of unity higher than 0.5 A/W at 1550 nm.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S215-S218
Mushroom Mesa Structure for InAlAs–InGaAs Avalanche Photodiodes
Mushroom mesa structure for InAlAs/InGaAs avalanche photodiodes (APD) was proposed and investigated. APD heterostructrures were grown by molecular-beam epitaxy. Fabricated APDs with the sensitive area diameter of about 30 micron were passivated by SiN deposition and demonstrated avalanche breakdown voltage Vbr 70–80 V. At the applied bias of 0.9 Vbr, the dark current was 75–200 nA. The single-mode coupled APDs demonstrated responsivity at a gain of unity higher than 0.5 A/W at 1550 nm.
- 1 November 2022
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 89 (11) , 681-686
1.55-µm range optical transmitter based on a vertical-cavity surface-emitting laser
Subject of study. A high-speed fiber-optic transmitter for the spectral range of 1.55 µm, based on a vertical-cavity surface-emitting laser (VCSEL) fabricated using wafer fusion technology was investigated. Aim of study. A comprehensive study of the parameters of the 1.55-µm range optical transmitter based on a VCSEL at room temperature is presented. Method. The heterostructure of the VCSEL was fabricated using molecular beam epitaxy and wafer fusion technology. The transmitter parameters were investigated with current modulation by a large signal in the non-return-to-zero (NRZ) format. Main results. At 20°C, the transmitter demonstrated maximum output optical power, exceeding 1 mW at the fiber output in single-mode operation. The maximum data rate over a short communication line based on an SMF-28 fiber with current amplitude modulation in the NRZ format reached 30 Gbits/s, limited by the modulation bandwidth reaching a value of approximately 12 GHz (at −3dB level). With an increase in the length of the fiber-optic communication line, the chromatic dispersion of the fiber and the chirp effect of the laser increase inter-symbol interference, which ultimately limits the speed and range of optical data transmission. Practical significance. The investigated fiber-optic transmitters are promising for both digital and analog transmission of high-frequency optical signals over fiber-optic communication lines.
- 1 November 2022
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 89 (11) , 681-686
1.55-µm range optical transmitter based on a vertical-cavity surface-emitting laser
Subject of study. A high-speed fiber-optic transmitter for the spectral range of 1.55 µm, based on a vertical-cavity surface-emitting laser (VCSEL) fabricated using wafer fusion technology was investigated. Aim of study. A comprehensive study of the parameters of the 1.55-µm range optical transmitter based on a VCSEL at room temperature is presented. Method. The heterostructure of the VCSEL was fabricated using molecular beam epitaxy and wafer fusion technology. The transmitter parameters were investigated with current modulation by a large signal in the non-return-to-zero (NRZ) format. Main results. At 20°C, the transmitter demonstrated maximum output optical power, exceeding 1 mW at the fiber output in single-mode operation. The maximum data rate over a short communication line based on an SMF-28 fiber with current amplitude modulation in the NRZ format reached 30 Gbits/s, limited by the modulation bandwidth reaching a value of approximately 12 GHz (at −3dB level). With an increase in the length of the fiber-optic communication line, the chromatic dispersion of the fiber and the chirp effect of the laser increase inter-symbol interference, which ultimately limits the speed and range of optical data transmission. Practical significance. The investigated fiber-optic transmitters are promising for both digital and analog transmission of high-frequency optical signals over fiber-optic communication lines.
- 1 November 2022
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 89 (11) , 677-680
Avalanche photodiodes based on InAlAs/InGaAs heterostructures with sulfide–polyamide passivation of mesa structures
Subject of study. A method for the sulfide–polyamide surface passivation of mesa structures of InAlAs/InGaAs avalanche photodiodes was considered and the static properties of the fabricated crystals of InAlAs/InGaAs avalanche photodiodes were investigated. Aim of study. The study aimed to investigate the effect of sulfide–polyamide surface passivation of mesa structures on the principal parameters of an avalanche photodiode. Method. Sulfide–polyamide surface passivation of a mesa structure entails processing the surface in an aqueous solution of ammonium sulfide followed by the application of a protective layer of AD-9103-30 polyamide. Main results. Avalanche photodiodes based on InAlAs/InGaAs heterostructures were fabricated and investigated. The surface of the mesa structure of avalanche photodiodes underwent sulfide–polyamide passivation. Crystals of avalanche photodiodes with an active area diameter of 32 µm reproducibly ensured a dark current of 10–20 nA under an applied voltage of 0.9 of the breakdown voltage, uniform distribution of the breakdown voltage value across the sample area, and the long-term stability of parameters. Spectral sensitivity values of the devices in the 1550 nm region were 0.85–0.88 A/W, and their capacitance values were 0.11–0.12 pF. Ensuring the reproducibility and long-term stability of parameters is crucial to passivation technology. Parameter measurements of the avalanche photodiode crystals with sulfide–polyamide passivation performed with a 6-month interval confirmed the temporal stability of the dark current at the level of 5%. Practical significance. The proposed method for the surface passivation of the mesa structure of InAlAs/InGaAs avalanche photodiodes entailing processing in an aqueous solution of ammonium sulfide followed by the application of a protective layer of AD-9103-30 polyamide can be used to fabricate avalanche photodiodes with a reproducible low level of dark current.
- 1 November 2022
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 89 (11) , 677-680
Avalanche photodiodes based on InAlAs/InGaAs heterostructures with sulfide–polyamide passivation of mesa structures
Subject of study. A method for the sulfide–polyamide surface passivation of mesa structures of InAlAs/InGaAs avalanche photodiodes was considered and the static properties of the fabricated crystals of InAlAs/InGaAs avalanche photodiodes were investigated. Aim of study. The study aimed to investigate the effect of sulfide–polyamide surface passivation of mesa structures on the principal parameters of an avalanche photodiode. Method. Sulfide–polyamide surface passivation of a mesa structure entails processing the surface in an aqueous solution of ammonium sulfide followed by the application of a protective layer of AD-9103-30 polyamide. Main results. Avalanche photodiodes based on InAlAs/InGaAs heterostructures were fabricated and investigated. The surface of the mesa structure of avalanche photodiodes underwent sulfide–polyamide passivation. Crystals of avalanche photodiodes with an active area diameter of 32 µm reproducibly ensured a dark current of 10–20 nA under an applied voltage of 0.9 of the breakdown voltage, uniform distribution of the breakdown voltage value across the sample area, and the long-term stability of parameters. Spectral sensitivity values of the devices in the 1550 nm region were 0.85–0.88 A/W, and their capacitance values were 0.11–0.12 pF. Ensuring the reproducibility and long-term stability of parameters is crucial to passivation technology. Parameter measurements of the avalanche photodiode crystals with sulfide–polyamide passivation performed with a 6-month interval confirmed the temporal stability of the dark current at the level of 5%. Practical significance. The proposed method for the surface passivation of the mesa structure of InAlAs/InGaAs avalanche photodiodes entailing processing in an aqueous solution of ammonium sulfide followed by the application of a protective layer of AD-9103-30 polyamide can be used to fabricate avalanche photodiodes with a reproducible low level of dark current.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (14) , 28
Mushroom mesa structure for InAlAs-InGaAs avalanche photodiodes
Mushroom mesa structure for InAlAs/InGaAs avalanche photodiodes (APD) was proposed and investigated. APD heterostructrures were grown by molecular-beam epitaxy. Fabricated APDs with the sensitive area diameter of about 30 micron were passivated by SiN deposition and demonstrated avalanche breakdown voltage Vbr 70-80 V. At the applied bias of 0.9 Vbr, the dark current was 75-200 nA. The single-mode coupled APDs demonstrated responsivity at a gain of unity higher than 0.5A/W at 1550 nm. Keywords: avalanche photodiode, InAlAs/InGaAs, mesa structure, dark current.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (14) , 28
Mushroom mesa structure for InAlAs-InGaAs avalanche photodiodes
Mushroom mesa structure for InAlAs/InGaAs avalanche photodiodes (APD) was proposed and investigated. APD heterostructrures were grown by molecular-beam epitaxy. Fabricated APDs with the sensitive area diameter of about 30 micron were passivated by SiN deposition and demonstrated avalanche breakdown voltage Vbr 70-80 V. At the applied bias of 0.9 Vbr, the dark current was 75-200 nA. The single-mode coupled APDs demonstrated responsivity at a gain of unity higher than 0.5A/W at 1550 nm. Keywords: avalanche photodiode, InAlAs/InGaAs, mesa structure, dark current.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (14) , 46
Impact of transverse optical confinment on performance of 1.55 μm vertical-cavity surface-emitting lasers with a buried tunnel junction
The impact of transverse optical confinement on the static and spectral characteristics of 1.55 μm vertical-cavity surface-emitting lasers (WF-VCSEL) with a buried tunnel junction (BTJ) n++-InGaAs/p++-InGaAs/p++-InAlGaAs, implemented using molecular-beam epitaxy and wafer fusion. It was found that for VCSELs with a tunnel junction (TJ) etching depth of 15 nm, the single-mode lasing occurs up to 8 μm BTJ mesa size due to a relatively weak lateral optical confinement, while the effect of a saturable absorber (SA) appears when the BTJ mesa size is less than 7 μm. Enhancing lateral optical confinement by increasing the BTJ etching depth up to 20 nm leads to suppression of the SA effect at the BTJ mesa size of 5-6 μm, but simultaneously limits the maximum single-mode optical power. According to obtained results an increase in the spectral mismatch between the maximum of the gain spectrum of the active region and the resonance wavelength of the WF-VCSEL up to ~ 35-50 nm will make it possible to suppress the undesirable SA effect in a wide range of the BTJ mesa sizes maintaining the single-mode lasing. Keywords: vertical-cavity surface-emitting laser, wafer fusion, molecular beam epitaxy, single-mode operation, saturable absorber.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (14) , 46
Impact of transverse optical confinment on performance of 1.55 μm vertical-cavity surface-emitting lasers with a buried tunnel junction
The impact of transverse optical confinement on the static and spectral characteristics of 1.55 μm vertical-cavity surface-emitting lasers (WF-VCSEL) with a buried tunnel junction (BTJ) n++-InGaAs/p++-InGaAs/p++-InAlGaAs, implemented using molecular-beam epitaxy and wafer fusion. It was found that for VCSELs with a tunnel junction (TJ) etching depth of 15 nm, the single-mode lasing occurs up to 8 μm BTJ mesa size due to a relatively weak lateral optical confinement, while the effect of a saturable absorber (SA) appears when the BTJ mesa size is less than 7 μm. Enhancing lateral optical confinement by increasing the BTJ etching depth up to 20 nm leads to suppression of the SA effect at the BTJ mesa size of 5-6 μm, but simultaneously limits the maximum single-mode optical power. According to obtained results an increase in the spectral mismatch between the maximum of the gain spectrum of the active region and the resonance wavelength of the WF-VCSEL up to ~ 35-50 nm will make it possible to suppress the undesirable SA effect in a wide range of the BTJ mesa sizes maintaining the single-mode lasing. Keywords: vertical-cavity surface-emitting laser, wafer fusion, molecular beam epitaxy, single-mode operation, saturable absorber.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics
- Vol. 67 (15) , 2432
Investigation of the characteristics of the InGaAs/InAlGaAs superlattice for 1300 nm range vertical-cavity surface-emitting lasers
X-ray structural analysis and photoluminescence spectroscopy techniques were used to study heterostructures based on InGaAs/InAlGaAs superlattice for active regions of 1300 nm range lasers grown by molecular beam epitaxy. It is shown that the grown heterostructures have a high crystal quality. The perpendicular lattice mismatch of the average crystal lattice constant of the InGaAs/InAlGaAs superlattice with respect to the crystal lattice constant of the InP substrate is estimated at ~+0.01%. An analysis of the photoluminescence spectra made it possible to conclude that the contribution of Auger recombination is insignificant in the studied range of excitation power density. Studies of vertical-cavity surface-emitting lasers with an active region based on the InGaAs/InAlGaAs superlattice made it possible to estimate the gain coefficient at a level of 650 cm-1 for the standard logarithmic approximation of the dependence of the gain on the current density. The transparency current density of the laser was 400-630 A/cm2, which is comparable to the record low values for the case of highly strained InGaAs-GaAs and InGaAsN-GaAs quantum wells in the spectral ranges of 1300 nm, respectively. Keywords: superlattice, vertical-cavity surface-emitting laser, optical gain.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics
- Vol. 67 (15) , 2432
Investigation of the characteristics of the InGaAs/InAlGaAs superlattice for 1300 nm range vertical-cavity surface-emitting lasers
X-ray structural analysis and photoluminescence spectroscopy techniques were used to study heterostructures based on InGaAs/InAlGaAs superlattice for active regions of 1300 nm range lasers grown by molecular beam epitaxy. It is shown that the grown heterostructures have a high crystal quality. The perpendicular lattice mismatch of the average crystal lattice constant of the InGaAs/InAlGaAs superlattice with respect to the crystal lattice constant of the InP substrate is estimated at ~+0.01%. An analysis of the photoluminescence spectra made it possible to conclude that the contribution of Auger recombination is insignificant in the studied range of excitation power density. Studies of vertical-cavity surface-emitting lasers with an active region based on the InGaAs/InAlGaAs superlattice made it possible to estimate the gain coefficient at a level of 650 cm-1 for the standard logarithmic approximation of the dependence of the gain on the current density. The transparency current density of the laser was 400-630 A/cm2, which is comparable to the record low values for the case of highly strained InGaAs-GaAs and InGaAsN-GaAs quantum wells in the spectral ranges of 1300 nm, respectively. Keywords: superlattice, vertical-cavity surface-emitting laser, optical gain.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (12) , 78
Peculiarities of growth of InAs quantum dot arrays with low surface density by molecular beam epitaxy
The influence of the substrate temperature and the flux of In adatoms on the structural and optical characteristics of InAs quantum dots with a low surface density is experimentally studied. An increase in the substrate temperature under conditions of a high flux of In adatoms promotes an increase in their surface migration and a certain decrease in the density of the array of quantum dots (down to ~ (1-2)· 1010 cm-2), however, in this case a significant short-wavelength shift of the photoluminescence spectrum is observed despite an increase in lateral sizes of dots. A decrease in the incident flux of In adatoms at optimal substrate temperatures makes it possible to reduce the dot density more efficiently (down to ~ (1-2)· 109 cm-2). Keywords: molecular-beam epitaxy, quantum dots, surface density.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (12) , 78
Peculiarities of growth of InAs quantum dot arrays with low surface density by molecular beam epitaxy
The influence of the substrate temperature and the flux of In adatoms on the structural and optical characteristics of InAs quantum dots with a low surface density is experimentally studied. An increase in the substrate temperature under conditions of a high flux of In adatoms promotes an increase in their surface migration and a certain decrease in the density of the array of quantum dots (down to ~ (1-2)· 1010 cm-2), however, in this case a significant short-wavelength shift of the photoluminescence spectrum is observed despite an increase in lateral sizes of dots. A decrease in the incident flux of In adatoms at optimal substrate temperatures makes it possible to reduce the dot density more efficiently (down to ~ (1-2)· 109 cm-2). Keywords: molecular-beam epitaxy, quantum dots, surface density.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Semiconductors
- Vol. 56 (8) , 598
1550 nm range high-speed single-mode vertical-cavity surface-emitting lasers
The results of complex studies of static and dynamic performance of 1550 nm-range VCSELs, which were created by direct bonding (wafer fusion technique) InAlGaAs/InP optical cavity wafers with AlGaAs/GaAs distributed Bragg reflector wafers grown by molecular beam epitaxy, are presented. The VCSELs with a buried tunnel junction diameter less than 7 μm demonstrated a single-mode lasing with a side-mode suppression ratio more than 40 dB; however, at diameters less than 5 μm, a sharp increase in the threshold current is observed. It is associated to the appearance of a saturable absorber due to penetration of optical mode into the non-pumped regions of the active region. The maximum single-mode output optical power and the -3 dB modulation bandwidth reached 4.5 mW and 8 GHz, respectively, at 20oC. The maximum data rate at 20oC under non-return-to-zero on-off keying modulation was 23 Gb/s for a short-reach link based on single-mode fiber SMF-28. As the length of the optical link increased up to 2000 m, the maximum data rate dropped to 18 Gbit/s. The main factors affecting the high-speed operation and data transmission range are defined and discussed, and the further ways to overcome themit are proposed. Keywords: VCSEL, wafer fusion, molecular beam epitaxy, single-mode operation, high-speed performance.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Semiconductors
- Vol. 56 (8) , 598
1550 nm range high-speed single-mode vertical-cavity surface-emitting lasers
The results of complex studies of static and dynamic performance of 1550 nm-range VCSELs, which were created by direct bonding (wafer fusion technique) InAlGaAs/InP optical cavity wafers with AlGaAs/GaAs distributed Bragg reflector wafers grown by molecular beam epitaxy, are presented. The VCSELs with a buried tunnel junction diameter less than 7 μm demonstrated a single-mode lasing with a side-mode suppression ratio more than 40 dB; however, at diameters less than 5 μm, a sharp increase in the threshold current is observed. It is associated to the appearance of a saturable absorber due to penetration of optical mode into the non-pumped regions of the active region. The maximum single-mode output optical power and the -3 dB modulation bandwidth reached 4.5 mW and 8 GHz, respectively, at 20oC. The maximum data rate at 20oC under non-return-to-zero on-off keying modulation was 23 Gb/s for a short-reach link based on single-mode fiber SMF-28. As the length of the optical link increased up to 2000 m, the maximum data rate dropped to 18 Gbit/s. The main factors affecting the high-speed operation and data transmission range are defined and discussed, and the further ways to overcome themit are proposed. Keywords: VCSEL, wafer fusion, molecular beam epitaxy, single-mode operation, high-speed performance.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (15)
Analysis of internal optical loss of 1.3 μm vertical-cavity surface-emitting laser based on n-=SUP=-++-=/SUP=--InGaAs/p-=SUP=-++-=/SUP=--InGaAs/p-=SUP=-++-=/SUP=--InAlGaAs tunnel junction
The analysis of internal optical loss and internal quantum efficiency in 1.3 μm-range InAlGaAsP/AlGaAs a composite n+-InGaAs/p+-InGaAs/p+-InAlGaAs tunnel junction obtained in the frame of molecular-beam epitaxy and wafer fusion technology. The level of internal optical losses in the lasers under study was varied by depositing a dielectric layer on the surface of the output mirror. It is shown that it is possible in principle to achieve low internal optical loss of less than 0.08% and 0.14% per one pass (round-trip) at temperatures of 20oC and 90oC, respectively. Keywords: vertical-cavity surface-emitting laser, wafer fusion, tunnel junction, superlattice, internal optical loss.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (15)
Analysis of internal optical loss of 1.3 μm vertical-cavity surface-emitting laser based on n-=SUP=-++-=/SUP=--InGaAs/p-=SUP=-++-=/SUP=--InGaAs/p-=SUP=-++-=/SUP=--InAlGaAs tunnel junction
The analysis of internal optical loss and internal quantum efficiency in 1.3 μm-range InAlGaAsP/AlGaAs a composite n+-InGaAs/p+-InGaAs/p+-InAlGaAs tunnel junction obtained in the frame of molecular-beam epitaxy and wafer fusion technology. The level of internal optical losses in the lasers under study was varied by depositing a dielectric layer on the surface of the output mirror. It is shown that it is possible in principle to achieve low internal optical loss of less than 0.08% and 0.14% per one pass (round-trip) at temperatures of 20oC and 90oC, respectively. Keywords: vertical-cavity surface-emitting laser, wafer fusion, tunnel junction, superlattice, internal optical loss.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (15) , 45
Investigation of the noise characteristics of vertical-cavity surface-emitting laser with a rhomboidal oxide current aperture for use in a Cs-based compact atomic magnetometer
The possibility of using vertical-emitting lasers with intracavity contacts (IC-VCSEL) and a rhomboidal oxide current aperture for creating a non-zero magnetic field optically pumped atomic magnetometers (OPM) with a 133Cs vapor cell for magnetoencephalographic (MEG) systems were demonstrated. Relative intensity noise (RIN) and polarization resolved RIN of the IC-VCSEL in the 895 nm range with different mirror losses (linewidth) in the frequency range from 1 Hz to 100 kHz were experimentally investigated. Lasers with low mirror loss (narrow linewidth) have polarization resolved RIN comparable to amplitude noise. For IC-VCSEL with an output optical power of 0.8 mW and a linewidth of 55 MHz, the noise level measured is 148 dB/Hz in 1 Hz bandwidth at 40 kHz frequency. The ultimate sensitivity of OPM based on two-beam MZ-scheme with studied VCSELs was estimated as ~ 11 fT/sqrt(Hz)sqrt. Keywords: vertical-cavity surface-emitting laser (VCSEL), magnetoencephalographic (MEG) systems, optically pumped atomic magnetometers (OPAM), relative intensity noise (RIN), polarization-resolved RIN.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (15) , 45
Investigation of the noise characteristics of vertical-cavity surface-emitting laser with a rhomboidal oxide current aperture for use in a Cs-based compact atomic magnetometer
The possibility of using vertical-emitting lasers with intracavity contacts (IC-VCSEL) and a rhomboidal oxide current aperture for creating a non-zero magnetic field optically pumped atomic magnetometers (OPM) with a 133Cs vapor cell for magnetoencephalographic (MEG) systems were demonstrated. Relative intensity noise (RIN) and polarization resolved RIN of the IC-VCSEL in the 895 nm range with different mirror losses (linewidth) in the frequency range from 1 Hz to 100 kHz were experimentally investigated. Lasers with low mirror loss (narrow linewidth) have polarization resolved RIN comparable to amplitude noise. For IC-VCSEL with an output optical power of 0.8 mW and a linewidth of 55 MHz, the noise level measured is 148 dB/Hz in 1 Hz bandwidth at 40 kHz frequency. The ultimate sensitivity of OPM based on two-beam MZ-scheme with studied VCSELs was estimated as ~ 11 fT/sqrt(Hz)sqrt. Keywords: vertical-cavity surface-emitting laser (VCSEL), magnetoencephalographic (MEG) systems, optically pumped atomic magnetometers (OPAM), relative intensity noise (RIN), polarization-resolved RIN.