Johann Kollegger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Johann Kollegger has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Tobias Huber
Technische Universität Wien Institut für Tragkonstruktionen – Betonbau Karlsplatz 13/E212‐2 1040 Wien
9 shared publications - Michael Rath
Institute of Structural Engineering (Structural Concrete) TU Wien Vienna Austria
8 shared publications - Benjamin Kromoser
University of Natural Resources and Life Sciences Vienna (BOKU)
6 shared publications - Patrick Huber
Institute of Structural Engineering, TU Wien Vienna Austria
6 shared publications - Franz Untermarzoner
Institute of Structural Engineering (Structural Concrete) TU Wien Vienna Austria
4 shared publications - Hannes Wolfger
Technische Universität Wien Institut für Tragkonstruktionen, Forschungsbereich Stahlbeton‐ und Massivbau Karlsplatz 13/212‐2 1040 Wien
4 shared publications
Latest Publications
- 26 April 2024
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 119 (6) , 431-444
Zur Querkrafttragfähigkeit von dünnwandigen Hohlkästen mit unbewehrten Fugen in den Stegen
Im Zuge des an der TU Wien in Entwicklung befindlichen LT‐Brückenbauverfahrens (L: Longitudinal, T: Transversal) werden dünnwandige Hohlkästen aus Beton als Längsträger (L) mit Fahrbahnplattenelementen (T) und Ortbeton kombiniert. Aufgrund des Bauablaufs verbleiben unbewehrte Fugen in den Stegen dieser Hohlkästen, während die Boden‐ und Deckplatten aufgrund der Ortbetonschichten durchlaufend bewehrt werden können. Es stellt sich die Frage, wie sich diese Fugenkonstellation auf die Quertragfähigkeit der Hohlkastenträger auswirkt. Um ein grundsätzliches Verständnis zu erlangen, wurden zwei großformatige Versuchskörper, einer mit Fugen in den Stegen und einer ohne, experimentell untersucht. Die Querkrafttragfähigkeit des Trägers mit Fugen entsprach in etwa jener des Trägers ohne Fugen, wodurch es demnach trotz der Fugen möglich war, nennenswerte Querkräfte zu übertragen. Als maßgebend für das Querkrafttragverhalten stellte sich die Fugenöffnung dar, da die an die Fuge angrenzenden Bügel wie eine Aufhängebewehrung agieren. So empfiehlt sich eine lokale Erhöhung der Bügelbewehrung in diesem Bereich. Um die Auswirkungen der Vorspannung, wie im LT‐Verfahren vorgesehen, auf das Tragverhalten zu analysieren, wurden nichtlineare Finite‐Elemente‐Untersuchungen durchgeführt. Es konnte gezeigt werden, dass das Tragverhalten des vorgespannten Trägers mit Fugen jenem des Trägers ohne Fugen weitestgehend entspricht.
- 26 April 2024
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 119 (6) , 431-444
Zur Querkrafttragfähigkeit von dünnwandigen Hohlkästen mit unbewehrten Fugen in den Stegen
Im Zuge des an der TU Wien in Entwicklung befindlichen LT‐Brückenbauverfahrens (L: Longitudinal, T: Transversal) werden dünnwandige Hohlkästen aus Beton als Längsträger (L) mit Fahrbahnplattenelementen (T) und Ortbeton kombiniert. Aufgrund des Bauablaufs verbleiben unbewehrte Fugen in den Stegen dieser Hohlkästen, während die Boden‐ und Deckplatten aufgrund der Ortbetonschichten durchlaufend bewehrt werden können. Es stellt sich die Frage, wie sich diese Fugenkonstellation auf die Quertragfähigkeit der Hohlkastenträger auswirkt. Um ein grundsätzliches Verständnis zu erlangen, wurden zwei großformatige Versuchskörper, einer mit Fugen in den Stegen und einer ohne, experimentell untersucht. Die Querkrafttragfähigkeit des Trägers mit Fugen entsprach in etwa jener des Trägers ohne Fugen, wodurch es demnach trotz der Fugen möglich war, nennenswerte Querkräfte zu übertragen. Als maßgebend für das Querkrafttragverhalten stellte sich die Fugenöffnung dar, da die an die Fuge angrenzenden Bügel wie eine Aufhängebewehrung agieren. So empfiehlt sich eine lokale Erhöhung der Bügelbewehrung in diesem Bereich. Um die Auswirkungen der Vorspannung, wie im LT‐Verfahren vorgesehen, auf das Tragverhalten zu analysieren, wurden nichtlineare Finite‐Elemente‐Untersuchungen durchgeführt. Es konnte gezeigt werden, dass das Tragverhalten des vorgespannten Trägers mit Fugen jenem des Trägers ohne Fugen weitestgehend entspricht.
- Open Access
- 16 April 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (4) , 2784-2799
The Wieselburg Bridge collapse—Analysis of the shear capacity based on forensic data
This paper describes the structural aspects of the Wieselburg Bridge collapse in Austria. The original design and reinforcing details for this integral concrete bridge are discussed. The collapse of the bridge is re‐constructed based on forensic documentation of the failure. The results of structural analysis carried out using material properties obtained after failure are compared to the shear capacity obtained from various models and from test results from literature. The results are used to explain the cause of failure of the integral bridge under dead load.
- 16 April 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (4) , 2784-2799
Open AccessThe Wieselburg Bridge collapse—Analysis of the shear capacity based on forensic data
This paper describes the structural aspects of the Wieselburg Bridge collapse in Austria. The original design and reinforcing details for this integral concrete bridge are discussed. The collapse of the bridge is re‐constructed based on forensic documentation of the failure. The results of structural analysis carried out using material properties obtained after failure are compared to the shear capacity obtained from various models and from test results from literature. The results are used to explain the cause of failure of the integral bridge under dead load.
- 6 December 2023
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 119 (2) , 111-119
Experimentelle Bestimmung der Ermüdungseigenschaften von heftgeschweißter Bewehrung
- 6 December 2023
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 119 (2) , 111-119
Experimentelle Bestimmung der Ermüdungseigenschaften von heftgeschweißter Bewehrung
- Open Access
Long-Term Shrinkage Measurements on Large-Scale Specimens Exposed to Real Environmental Conditions
This article presents an experimental testing campaign on large-scale concrete specimens with cross-sectional areas of up to 1 m2 and a specimen length of 3 m. The primary goal of the testing campaign was to study the shrinkage behaviour of large-scale specimens exposed to real environmental conditions. Large-scale prismatic concrete specimens were equipped with vibrating wire strain gauges to monitor the strain evolution inside the specimens. To analyse the shrinkage behaviour of the specimens, the thermal strain had to be deducted from the measured strain. To study the influence of seasonal environmental conditions, different specimen production dates (in summer and winter) were examined. The measured shrinkage strains of the large-scale specimens are compared with the results of shrinkage models developed by two engineering entities (fib (Fédération Internationale du Béton) and RILEM (International Union of Laboratories and Experts in Construction, Materials, Systems and Structures)). The comparison shows a poor agreement of the measurements with the models, even though the results from the model for small specimens tested in the laboratory under constant environmental condition agree well with the experimental results. This leads to the conclusion that the poor agreement between the measurements and the shrinkage models must be due to the seasonally changing environmental conditions. The comparison of the results from specimens with different production dates shows that different shrinkage behaviour occurs, especially in the first year of measurements.
Open AccessLong-Term Shrinkage Measurements on Large-Scale Specimens Exposed to Real Environmental Conditions
This article presents an experimental testing campaign on large-scale concrete specimens with cross-sectional areas of up to 1 m2 and a specimen length of 3 m. The primary goal of the testing campaign was to study the shrinkage behaviour of large-scale specimens exposed to real environmental conditions. Large-scale prismatic concrete specimens were equipped with vibrating wire strain gauges to monitor the strain evolution inside the specimens. To analyse the shrinkage behaviour of the specimens, the thermal strain had to be deducted from the measured strain. To study the influence of seasonal environmental conditions, different specimen production dates (in summer and winter) were examined. The measured shrinkage strains of the large-scale specimens are compared with the results of shrinkage models developed by two engineering entities (fib (Fédération Internationale du Béton) and RILEM (International Union of Laboratories and Experts in Construction, Materials, Systems and Structures)). The comparison shows a poor agreement of the measurements with the models, even though the results from the model for small specimens tested in the laboratory under constant environmental condition agree well with the experimental results. This leads to the conclusion that the poor agreement between the measurements and the shrinkage models must be due to the seasonally changing environmental conditions. The comparison of the results from specimens with different production dates shows that different shrinkage behaviour occurs, especially in the first year of measurements.
- Open Access
- 3 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (13) , 7825
Deck Slab Elements for the Accelerated Construction of Steel–Concrete Composite Bridges
Various methods have been developed to produce deck slabs for steel–concrete composite bridges. Usually, the deck slabs are cast with in situ concrete using a formwork carriage, resulting in construction progress of 15 to 25 m of deck slab per week. A new construction method was developed at the Institute of Structural Engineering (TU Wien), which enables the swift erection of the concrete deck slab. This method employs precast deck slab elements with reinforced concrete cross-beams which span in the transverse direction. With this new construction method, producing up to two deck slab sections of 15–25 m per day becomes possible. Further, the performance of novel reinforcement detailing required for the precast deck slab elements is investigated by structural testing. The experiments consist of eight load-bearing tests on four specimens which represent sections of the element during casting and after completion. The investigated parameters in series 1 are the length and spacing of loops, used for protruding longitudinal bars enclosure. In series 2, the enclosure of the shear reinforcement and the height of the cross beams are varied. The results show that the targeted bending capacity could be reached in all tests with no signs of premature failure due to detailing reasons. Based on the experimental results, the feasibility of the new approach is shown and recommendations for detailing are given.
- 3 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (13) , 7825
Open AccessDeck Slab Elements for the Accelerated Construction of Steel–Concrete Composite Bridges
Various methods have been developed to produce deck slabs for steel–concrete composite bridges. Usually, the deck slabs are cast with in situ concrete using a formwork carriage, resulting in construction progress of 15 to 25 m of deck slab per week. A new construction method was developed at the Institute of Structural Engineering (TU Wien), which enables the swift erection of the concrete deck slab. This method employs precast deck slab elements with reinforced concrete cross-beams which span in the transverse direction. With this new construction method, producing up to two deck slab sections of 15–25 m per day becomes possible. Further, the performance of novel reinforcement detailing required for the precast deck slab elements is investigated by structural testing. The experiments consist of eight load-bearing tests on four specimens which represent sections of the element during casting and after completion. The investigated parameters in series 1 are the length and spacing of loops, used for protruding longitudinal bars enclosure. In series 2, the enclosure of the shear reinforcement and the height of the cross beams are varied. The results show that the targeted bending capacity could be reached in all tests with no signs of premature failure due to detailing reasons. Based on the experimental results, the feasibility of the new approach is shown and recommendations for detailing are given.
- Open Access
- 30 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6657
On the Torsional Behavior of the Longitudinal Bridge Girders Used in the LT-Bridge Construction Method
A new bridge construction method, combining semi-precast elements and in situ concrete, has been developed at TU Wien, with the aim of decreasing erection time. In the course of construction using this new method, structural conditions arise that render a more detailed investigation necessary. By connecting a precast, thin-walled box girder to a bridge segment located on a pier by means of post-tensioning, a joint is created. By casting in situ concrete on the bottom and top slabs, the joint can be bridged with longitudinal reinforcement; however, the unreinforced vertical joints in the webs remain. This detail is a specific characteristic of the LT-bridge construction method and needs to be further investigated and assessed, as the question arises as to how this circumstance affects the torsional bearing behavior of the bridge superstructure. Torsion tests described in the literature consider ordinary box girders with longitudinal reinforcement or post-tensioned segmental bridges without longitudinal reinforcement at the joints. Therefore, the new reinforcement layout at the joints had to be investigated experimentally. Two large-scale thin-walled box girders—one without joints in the webs and the other with unreinforced joints in the webs—were tested, allowing for a direct comparison of conventionally manufactured bridges and those erected with the new bridge construction method. Furthermore, we investigated whether the results of common calculation methods corresponded to the experimental findings.
- 30 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6657
Open AccessOn the Torsional Behavior of the Longitudinal Bridge Girders Used in the LT-Bridge Construction Method
A new bridge construction method, combining semi-precast elements and in situ concrete, has been developed at TU Wien, with the aim of decreasing erection time. In the course of construction using this new method, structural conditions arise that render a more detailed investigation necessary. By connecting a precast, thin-walled box girder to a bridge segment located on a pier by means of post-tensioning, a joint is created. By casting in situ concrete on the bottom and top slabs, the joint can be bridged with longitudinal reinforcement; however, the unreinforced vertical joints in the webs remain. This detail is a specific characteristic of the LT-bridge construction method and needs to be further investigated and assessed, as the question arises as to how this circumstance affects the torsional bearing behavior of the bridge superstructure. Torsion tests described in the literature consider ordinary box girders with longitudinal reinforcement or post-tensioned segmental bridges without longitudinal reinforcement at the joints. Therefore, the new reinforcement layout at the joints had to be investigated experimentally. Two large-scale thin-walled box girders—one without joints in the webs and the other with unreinforced joints in the webs—were tested, allowing for a direct comparison of conventionally manufactured bridges and those erected with the new bridge construction method. Furthermore, we investigated whether the results of common calculation methods corresponded to the experimental findings.
- 22 April 2022
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 117 (6) , 397-409
Frühzeitiges Versagen bei hochfesten Stahlbetonstützen mit großen Stabdurchmessern
- 22 April 2022
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 117 (6) , 397-409
Frühzeitiges Versagen bei hochfesten Stahlbetonstützen mit großen Stabdurchmessern
- 18 February 2022
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 117 (4) , 245-255
Zur Einleitung von Vorspannkräften in dünnwandige Hohlkastenquerschnitte
- 18 February 2022
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 117 (4) , 245-255
Zur Einleitung von Vorspannkräften in dünnwandige Hohlkastenquerschnitte
- 1 January 2022
- Published by VDI Fachmedien GmbH and Co. KG in Bauingenieur
- Vol. 97 (11) , 374-384
Einleitung von Schubkräften in dünnwandige Fertigteilträger bei der Erstanwendung des Brückenklappverfahrens/Introduction of shear forces into thin- walled precast girders during the first application of the balanced lowering method
Bei der Erstanwendung des Brückenklappverfahrens bei zwei Brücken in Österreich wurden trogförmige Fertigteilträger mit 70 mm dicken Wandplatten eingesetzt. Verankerungs- und Umlenkkräfte von Spanngliedern und Abspannungen wurden über Querbalken in die dünnwandigen Fertigteilträger eingeleitet. Zur Aufnahme der Schubkräfte in den Fugen zwischen den Wandplatten und den Querbalken wurden Leiterbewehrungen verwendet. Die Verankerungs- länge der Leiterbewehrungen in den Wandplatten betrug nur 40 mm. In experimentellen Untersuchungen wurde die Tragfähigkeit der Schubfugen überprüft. Die experimentell ermittelten Schubspannungen beim Versagen stimmten gut mit den aufnehmbaren Schubspannungen gemäß Eurocode 2 überein, wenn mittlere Materialfestigkeiten in die Bemessungsgleichungen eingesetzt wurden. Damit konnte nachgewiesen werden, dass die kurzen Verankerungslängen der Leiterbewehrungen ausreichten, um eine sichere Eintragung der Schubkräfte in die Wandplatten beim Bau der Brücken über den Lahnbach und die Lafnitz zu gewährleisten.
- 1 January 2022
- Published by VDI Fachmedien GmbH and Co. KG in Bauingenieur
- Vol. 97 (11) , 374-384
Einleitung von Schubkräften in dünnwandige Fertigteilträger bei der Erstanwendung des Brückenklappverfahrens/Introduction of shear forces into thin- walled precast girders during the first application of the balanced lowering method
Bei der Erstanwendung des Brückenklappverfahrens bei zwei Brücken in Österreich wurden trogförmige Fertigteilträger mit 70 mm dicken Wandplatten eingesetzt. Verankerungs- und Umlenkkräfte von Spanngliedern und Abspannungen wurden über Querbalken in die dünnwandigen Fertigteilträger eingeleitet. Zur Aufnahme der Schubkräfte in den Fugen zwischen den Wandplatten und den Querbalken wurden Leiterbewehrungen verwendet. Die Verankerungs- länge der Leiterbewehrungen in den Wandplatten betrug nur 40 mm. In experimentellen Untersuchungen wurde die Tragfähigkeit der Schubfugen überprüft. Die experimentell ermittelten Schubspannungen beim Versagen stimmten gut mit den aufnehmbaren Schubspannungen gemäß Eurocode 2 überein, wenn mittlere Materialfestigkeiten in die Bemessungsgleichungen eingesetzt wurden. Damit konnte nachgewiesen werden, dass die kurzen Verankerungslängen der Leiterbewehrungen ausreichten, um eine sichere Eintragung der Schubkräfte in die Wandplatten beim Bau der Brücken über den Lahnbach und die Lafnitz zu gewährleisten.
- 15 October 2021
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 116 (12) , 958-968
Zur Ortbeton‐Ergänzung einschaliger Halbfertigteilwände
- 15 October 2021
- Published by Wiley in Beton- und Stahlbetonbau
- Vol. 116 (12) , 958-968
Zur Ortbeton‐Ergänzung einschaliger Halbfertigteilwände