LFL. Fornaro

L. Fornaro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


L. Fornaro has a total of 17 co-authors. Here are the top co-authors by number of shared publications:

  • Andrés Cuña

    Laboratorio de Energías Renovables, Instituto Polo Tecnológico de Pando, Facultad de Química, Universidad de la República, Pando, Canelones, Uruguay. Área Fisicoquímica, DETEMA, Facultad de Química, Universidad de la República, Montevideo, Uruguay

    3 shared publications
  • Ivana Aguiar

    Área Radioquímica, Facultad de Química, Universidad de la Republica, Montevideo, Uruguay

    3 shared publications
  • A. Noguera

    Compound Semiconductors Group, Radiochemistry Department, Faculty of Chemistry, Montevideo, Uruguay

    2 shared publications
  • A. Gancharov

    Compound Semiconductors Group, Radiochemistry Department, Faculty of Chemistry, Montevideo, Uruguay

    1 shared publication
  • A. Noguera

    Compound Semiconductors Group, Radiochemistry Department, Faculty of Chemistry, Montevideo, Uruguay

    1 shared publication
  • Edgardo Saucedo

    Institut de Recerca en Energia de Catalunya

    1 shared publication

Latest Publications

  • Improvements on Bismuth Tri-iodide Platelets For Room Temperature X-ray Detection

    by L. Fornaro, I. Aguiar, A. Noguera, M. Perez, M. Rodriguez

    Bismuth tri-iodide synthesized from bismuth carbonate and potassium iodide and then treated with hydriodic acid was used as starting material. Platelets were grown by physical vapor deposition (PVD), with a source temperature of 320 degC, during 1 day. Growth temperature was about 250 degC. Platelets are up to 30 times 20 mm 2 in size, and from 50 to 80 mum in thickness. Platelet surface exhibits extreme brightness and higher uniformity than the ones previously reported, confirmed by optical and scanning electron microscopy. Several reactants were used for platelets' surface etching; any of them did not improve the crystal surface. Detectors were made with the as-grown platelets by Pd thermal deposition (contact areas of 0.071 cm 2 ), with and without guard-ring, Pd wire attachment with aquadag and acrylic encapsulation. Detector X-ray response was measured by irradiation with a 241 Am source of 3.5 mR/h. Resistivities up to 1.7 times 10 13 Omega-cm were obtained, the best reported for detectors made with monocrystals of this material, which correlates with the fact that these detectors show the best signal to dark relation as response to an X-ray moderate radiation exposure: 11.0, with a bias of 60 V. This new generation of platelets give better surfaces, higher resistivities, lower dark currents and better signal to dark relation than previous ones.


  • Comparison Of Mercuric Bromide And Lead Bromide Layers as Photoconductors For Direct X-ray Imaging Applications

    by L. Fornaro, N. Sasen, M. Perez, A. Noguera, I. Aguiar

    Films of PbBr 2 and HgBr 2 were grown by the physical vapor deposition method onto ITO-coated or palladium-coated glass substrates 1"times1" in size. The best growth conditions were a source temperature of 500 degC, a growth temperature of 220 degC and a growth time of 192 hours, with an initial pressure of 4 times 10 -3 Pa, for PbBr 2 , and a source temperature of 150 degC, a growth temperature of 50 degC and a growth time of 2 hours with an initial pressure of 4 times 10 -3 Pa, for HgBr2 layers. Layers thicknesses and grain sizes gave values ranging between 40 and 60 mum (10%), and between 2 and 10 mum, respectively, for PbBr 2 , and about 300 mum and between 20 and 50 mum, respectively, for HgBr 2 . Layers were characterized by optical and scanning electron microscopies. The dark current density is lower than 10 pA/mm 2 for electric fields below 0.2 V/mum for HgBr 2 , and below 5 V/mum for PbBr 2 , and the resistivity is 5.4 times 10 13 Omega-cm for PbBr 2 and 4.9 times 10 12 Omega-cm for HgBr 2 . Signal to noise is 14 at 7.5 V/mum for PbBr 2 films and 0.31 at 0.2 V/mum for HgBr 2 films. Dark current density, resistivity and response to X-rays of the films are acceptable taking into account that this is the first report of layers of these materials as X-ray detectors, and indicate these heavy metal bromides as promising candidates for the application.


  • Growth of lead bromide polycrystalline films

    by M. Giles, A. Cuña, N. Sasen, M. Llorente, L. Fornaro

    Lead bromide polycrystalline films were grown by the physical vapor deposition method (PVD). Glass 1″x1″ in size, uncoated, and coated with Indium Tin Oxide (ITO), was used as substrate and rear contact. The starting material was evaporated at temperatures from 395°C to 530°C under high vacuum atmosphere (6 x 10‐3 Pa) and during 8 days. The substrate temperature was prefixed from 190°C to 220°C. Film thickness yielded values from 40 to 90 μm. Optical microscopy and scanning electron microscopy (SEM) were performed on the films. Grain size resulted to be from 1.0 to 3.5 μm. SEM and X‐ray diffraction indicate that films grow with a preferred orientation with the (0 0 l) planes parallel to the substrate. The Texture Coefficient (TC) related to the plane (0 0 6) was 7.3. Resistivity values in the order of 1012 Ωcm were obtained for the oriented samples, but a strong polarization indicates severe charge transport problems in the films. Film properties were correlated with the growth temperature and with previous results for films of other halides.


  • Growth of bismuth tri‐iodide platelets by the physical vapor deposition method

    by A. Cuña, A. Noguera, E. Saucedo, L. Fornaro

    The work reports the growth of single BI3 crystals with platelets habit. Platelets were grown by physical vapor deposition (PVD) in a high vacuum atmosphere and with argon, polymer or iodine as additives. Crystals grew in the zone of maximum temperature gradient, perpendicular to the ampoule wall. Crystals grown with argon as additive show a very shining surface, have hexagonal (0 0 l) faces, sizes up to 20 x 10 mm2 and thicknesses up to 100 μm. They were characterized by optical microscopy and scanning electron microscopy (SEM). Dendritic‐like structures were found to be their main surface defect. SEM indicates that they grow from the staking of hexagonal unities. Electrical properties of the crystals grown under different growth conditions were determined. Resistivities up to 2 x 1012 Ωcm (the best reported value for monocrystals of this material) were obtained. X‐ray response was measured by irradiation of the platelets with a 241Am source of 3.5 mR/h. A comparison of results according to the growth conditions was made. Properties of the crystals grown by this method are compared with the ones measured for others previously grown from the melt. Also, results for bismuth tri‐iodide platelets are compared with the ones obtained for mercuric and lead iodide platelets.


  • Correlation between growth orientation and growth temperature for bismuth tri‐iodide films

    by A. Cuña, I. Aguiar, A. Gancharov, M. Pérez, L. Fornaro

    This paper reports the growth of bismuth tri‐iodide thick films intended for direct and digital X‐ray imaging. Films were grown by the vertical physical vapor deposition method, onto glass substrates 2″x 2″ in size, with gold previously deposited as rear electrode. The film thickness was up to 33 μm (±5 %). Optical microscopy and SEM were performed on the films and grain size resulted to be up to 40 μm. A strong correlation was found between the microcrystals growth orientation and the growth temperature. At low temperatures, microcrystals grow with their c axis parallel to the substrate, whereas at higher temperatures, they grow with their c axis perpendicular to the substrate. The higher the growth temperature, the lower the dark current of the film, and the higher the resistivity, which was from 1013 to 1015 Ωcm. A sensitivity to X‐rays of 6.9 nC/R.cm2 was measured irradiating the films with X‐rays from a mamographer. Film properties were correlated with the growth temperature, with previous results for bismuth tri‐iodide films and monocrystals and with data for films of alternative materials such as lead and mercuric iodide.