André Lefebvre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
André Lefebvre has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Olivier Sinot
Laboratoire de Mécanique Biomécanique Polymère Structures, Ecole Nationale d'Ingénieurs de Metz, Metz, France
2 shared publications- Pawel Lipinski
Metz
2 shared publications Andrew Torrance
Department of Mechanical and Manufacturing Engineering , Trinity College , Dublin , Ireland
1 shared publicationArchibald A. Torrance
Department of Mechanical and Manufacturing Engineering, Trinity College, Dublin, Ireland
1 shared publicationC. Lescalier
Laboratoire de Génie Industriel et de Production Mécanique (LGIPM) , ENSAM, 4 rue Augustin Fresnel, Metz
1 shared publicationP. Vieville
Laboratoire de Fiabilité Mécanique , ENIM Ile du Saulcy, Metz
1 shared publication
Latest Publications
- 2 October 2014
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 18 (4) , 585-602
Determination of the Partition Coefficient for the Grinding of a HardWC-Co-CrCoating with a Diamond Wheel
□ Determination of the partition ratio is fundamental to a thermo-mechanical approach to the grinding process. To establish the energy balance, accurate measurements and numerical modelling must be combined. In this work, such a method is applied to the grinding of a HVOF WC-Cr-Co hard coating. A double pole grindable thermocouple was developed to measure the temperature in the arc of cut, and its effective length. The heat flux absorbed by the workpiece is found by fitting the numerical solution to the temperature profile measured during the cooling phase, behind the contact. Identical results for the heat flux may be obtained by fitting the results to the analytical solution from moving heat source theory, but the maximum interface temperature is underestimated. A finite element solution, using MSC Marc software allows a closer approach to the maximum temperature measured at the interface during grinding, provided that the thickness of the coating is correctly modelled.
- 2 October 2014
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 18 (4) , 585-602
Determination of the Partition Coefficient for the Grinding of a HardWC-Co-CrCoating with a Diamond Wheel
□ Determination of the partition ratio is fundamental to a thermo-mechanical approach to the grinding process. To establish the energy balance, accurate measurements and numerical modelling must be combined. In this work, such a method is applied to the grinding of a HVOF WC-Cr-Co hard coating. A double pole grindable thermocouple was developed to measure the temperature in the arc of cut, and its effective length. The heat flux absorbed by the workpiece is found by fitting the numerical solution to the temperature profile measured during the cooling phase, behind the contact. Identical results for the heat flux may be obtained by fitting the results to the analytical solution from moving heat source theory, but the maximum interface temperature is underestimated. A finite element solution, using MSC Marc software allows a closer approach to the maximum temperature measured at the interface during grinding, provided that the thickness of the coating is correctly modelled.
- 1 April 2013
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 17 (2) , 312-324
OPTIMIZATION OF DRESSING CONDITIONS FOR A RESIN-BONDED DIAMOND WHEEL BY TOPOGRAPHY ANALYSIS
The macro-geometry (run-out, shape, profile, etc.) and the micro-geometry (density, distribution, and shape of the grains) of a grinding wheel are measured after both truing and dressing. The effectiveness of the truing is studied by analysing the topography of the wheel to characterize the tool and its effect on workpiece surface quality during the grinding process. Using wheel replicas, the surfaces are analyzed with a non-contact interference microscope and the measurements are processed with MountainsMap Software. For different truing and dressing conditions, the dressing efficiency, the grain density, and its effects on the roughness and wear of the wheel in the grinding process are investigated.
- 1 April 2013
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 17 (2) , 312-324
OPTIMIZATION OF DRESSING CONDITIONS FOR A RESIN-BONDED DIAMOND WHEEL BY TOPOGRAPHY ANALYSIS
The macro-geometry (run-out, shape, profile, etc.) and the micro-geometry (density, distribution, and shape of the grains) of a grinding wheel are measured after both truing and dressing. The effectiveness of the truing is studied by analysing the topography of the wheel to characterize the tool and its effect on workpiece surface quality during the grinding process. Using wheel replicas, the surfaces are analyzed with a non-contact interference microscope and the measurements are processed with MountainsMap Software. For different truing and dressing conditions, the dressing efficiency, the grain density, and its effects on the roughness and wear of the wheel in the grinding process are investigated.
- 7 March 2008
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 12 (1) , 1-14
EXPERIMENTAL ANALYSIS OF TEMPERATURE IN GRINDING AT THE GLOBAL AND LOCAL SCALES
The purpose of the article is the experimental estimation of the global and local heat fluxes and the corresponding energy partition to the workpiece for regular grinding of 100Cr6 steel with aluminium oxide wheel. By using a grindable thermocouple, the temperature and the real contact length allow determination of the global heat flux and the partition ratio at the wheel scale. The high frequency analysis of the signal has shown maximum flash temperatures of about 1000°C corresponding to the local temperature under the chip-grain unit with very high heating speed of about 100°C/µs. The comparison between theoretical temperature decay and experimental cooling has demonstrated that the time response of the sensor is fast enough for the estimation of the local temperature and power due to the sliding of grain and to the plastic strain of ground materials.
- 7 March 2008
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 12 (1) , 1-14
EXPERIMENTAL ANALYSIS OF TEMPERATURE IN GRINDING AT THE GLOBAL AND LOCAL SCALES
The purpose of the article is the experimental estimation of the global and local heat fluxes and the corresponding energy partition to the workpiece for regular grinding of 100Cr6 steel with aluminium oxide wheel. By using a grindable thermocouple, the temperature and the real contact length allow determination of the global heat flux and the partition ratio at the wheel scale. The high frequency analysis of the signal has shown maximum flash temperatures of about 1000°C corresponding to the local temperature under the chip-grain unit with very high heating speed of about 100°C/µs. The comparison between theoretical temperature decay and experimental cooling has demonstrated that the time response of the sensor is fast enough for the estimation of the local temperature and power due to the sliding of grain and to the plastic strain of ground materials.