Sergey Salikeev
Sergey Salikeev has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
A. Burmistrov
7 shared publications- Alexey Raykov
Kazan National Research Technological University
6 shared publications M. Fomina
Kazan Natl Res Technol Univ, Dept Vacuum Equipment, Kazan, Russia
6 shared publicationsA. Raykov
2 shared publicationsAleksey Burmistrov
2 shared publicationsMarina Fomina
2 shared publications
Latest Publications
- 7 June 2021
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 33 (3) , 29-33
Working process of Roots vacuum pumps
Zusammenfassung: Entwicklung und Verifizierung des CFD‐Modells für WälzkolbenpumpenWälzkolbenpumpen sind aufgrund der Ölfreiheit des Arbeitsvolumens, der Einfachheit der Konstruktion, des hohen Arbeitsdurchsatzes und der Zuverlässigkeit weit verbreitet. Der Arbeitsprozess in Roots‐Gebläsen wurde mit Hilfe von Methoden der numerischen Strömungsmechanik (CFD) untersucht. Es wurde ein hexaedrisch strukturiertes Netz des Arbeitsvolumens mit konstanter Schrittweite über den Rotordrehwinkel erstellt. Luft wurde als Arbeitsmedium im Modell eines kompressiblen idealen Gases betrachtet. Für die Berechnung wurde das Turbulenzmodell Shear Stress Transport (SST) verwendet.Die Verifizierung des entwickelten mathematischen Modells wurde durch den Vergleich der berechneten und experimentell gewonnenen Beziehung zwischen der Fördermenge und dem Druckverhältnis bei verschiedenen Drehzahlen im Kompressorregime durchgeführt. Der Unterschied zwischen Berechnung und Experiment übersteigt nicht 8 %. Es wurde ein Vergleich zwischen berechneten und experimentellen Indikatordiagrammen in der Arbeitskammer durchgeführt und das Wälzkolben‐Vakuumpumpumpen‐Drehzahlniveau gemessen.Die maximale Differenz zwischen dem Experiment und der Berechnung mit der CFD‐Methode beträgt 9,8 %. In beiden Fällen kann der Unterschied zwischen Berechnung und Experiment vor allem durch Fehler bei der Messung der tatsächlichen Radialabstände erklärt werden. Die Analyse der Geschwindigkeitsfelder im Roots‐Gebläse, das im Vakuum‐ und Kompressorregime arbeitet, wurde mit Hilfe des CFD‐Modells durchgeführt. Die Gasgeschwindigkeit im Spalt ist bei niedrigen Drücken viel höher. Dies lässt sich durch die größere Druckdifferenz zwischen Einlass und Auslass bei Vakuumbedingungen erklären.
- 7 June 2021
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 33 (3) , 29-33
Working process of Roots vacuum pumps
Zusammenfassung: Entwicklung und Verifizierung des CFD‐Modells für WälzkolbenpumpenWälzkolbenpumpen sind aufgrund der Ölfreiheit des Arbeitsvolumens, der Einfachheit der Konstruktion, des hohen Arbeitsdurchsatzes und der Zuverlässigkeit weit verbreitet. Der Arbeitsprozess in Roots‐Gebläsen wurde mit Hilfe von Methoden der numerischen Strömungsmechanik (CFD) untersucht. Es wurde ein hexaedrisch strukturiertes Netz des Arbeitsvolumens mit konstanter Schrittweite über den Rotordrehwinkel erstellt. Luft wurde als Arbeitsmedium im Modell eines kompressiblen idealen Gases betrachtet. Für die Berechnung wurde das Turbulenzmodell Shear Stress Transport (SST) verwendet.Die Verifizierung des entwickelten mathematischen Modells wurde durch den Vergleich der berechneten und experimentell gewonnenen Beziehung zwischen der Fördermenge und dem Druckverhältnis bei verschiedenen Drehzahlen im Kompressorregime durchgeführt. Der Unterschied zwischen Berechnung und Experiment übersteigt nicht 8 %. Es wurde ein Vergleich zwischen berechneten und experimentellen Indikatordiagrammen in der Arbeitskammer durchgeführt und das Wälzkolben‐Vakuumpumpumpen‐Drehzahlniveau gemessen.Die maximale Differenz zwischen dem Experiment und der Berechnung mit der CFD‐Methode beträgt 9,8 %. In beiden Fällen kann der Unterschied zwischen Berechnung und Experiment vor allem durch Fehler bei der Messung der tatsächlichen Radialabstände erklärt werden. Die Analyse der Geschwindigkeitsfelder im Roots‐Gebläse, das im Vakuum‐ und Kompressorregime arbeitet, wurde mit Hilfe des CFD‐Modells durchgeführt. Die Gasgeschwindigkeit im Spalt ist bei niedrigen Drücken viel höher. Dies lässt sich durch die größere Druckdifferenz zwischen Einlass und Auslass bei Vakuumbedingungen erklären.
- 3 December 2020
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 32 (6) , 42-44
Study of oil free scroll vacuum pump characteristics
Summary: To verify the mathematical model of a scroll vacuum pump working process, an experimental unit for obtaining indicator diagrams was developed. The pump was modified to install gauges to measure quick‐varying pressures in the working chambers of the pump at different operating modes. The dependence of pressure on the rotation angle of the drive shaft at different inlet pressures is obtained. Comparison of experimental and calculated data shows convergence within 15 %.
- 3 December 2020
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 32 (6) , 42-44
Study of oil free scroll vacuum pump characteristics
Summary: To verify the mathematical model of a scroll vacuum pump working process, an experimental unit for obtaining indicator diagrams was developed. The pump was modified to install gauges to measure quick‐varying pressures in the working chambers of the pump at different operating modes. The dependence of pressure on the rotation angle of the drive shaft at different inlet pressures is obtained. Comparison of experimental and calculated data shows convergence within 15 %.
- 13 August 2019
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 31 (4) , 34-37
Indicator diagrams of oil free scroll vacuum pumps
Summary: Experimental test unit for obtaining indicator diagrams of a scroll vacuum pump was developed. Indicator diagrams for different pump inlet pressures and different rotation speeds of the drive shaft were obtained. The obtained results are analyzed.
- 13 August 2019
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 31 (4) , 34-37
Indicator diagrams of oil free scroll vacuum pumps
Summary: Experimental test unit for obtaining indicator diagrams of a scroll vacuum pump was developed. Indicator diagrams for different pump inlet pressures and different rotation speeds of the drive shaft were obtained. The obtained results are analyzed.
- 1 December 2018
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 30 (6) , 24-27
Scroll Geometry of Scroll Vacuum Pump Influence on pumping characteristics and indicated power
- 1 December 2018
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 30 (6) , 24-27
Scroll Geometry of Scroll Vacuum Pump Influence on pumping characteristics and indicated power
- 6 December 2017
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 29 (6) , 28-31
Mathematical model of working process of oil free scroll vacuum pump
Summary: A mathematical model of oil free scroll machine working in vacuum conditions is considered. Differential equations and main assumptions in the model are presented. Four types of control volumes are specified. The model takes into consideration heat exchange between the pump working elements, change of clearances due to thermal deformations, and mobility of the scroll element wall in calculation of leakage. The comparison of the calculated values of the pumping speed with experimental values obtained at different rotation speed of the driveshaft is carried out.
- 6 December 2017
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 29 (6) , 28-31
Mathematical model of working process of oil free scroll vacuum pump
Summary: A mathematical model of oil free scroll machine working in vacuum conditions is considered. Differential equations and main assumptions in the model are presented. Four types of control volumes are specified. The model takes into consideration heat exchange between the pump working elements, change of clearances due to thermal deformations, and mobility of the scroll element wall in calculation of leakage. The comparison of the calculated values of the pumping speed with experimental values obtained at different rotation speed of the driveshaft is carried out.
- 3 April 2017
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 29 (2) , 45-49
The working process of an oil‐free claw vacuum pump
Mathematical model of oil free claw vacuum pump is presented. The model is based on energy balance differential equations of thermodynamic system of variable mass working body.Using the equations of coordinates transformation and contact line of rotors continuity condition, equations for geometry of claw pump working chamber on condition of rotors point connection are obtained. To evaluate the leakage through the rotor mechanism channels, their existence graphs are plotted and geometric parameters of the channels depending on rotors position are determined.As a result of modeling, dependence of pressure and temperature in suction and compression‐discharge chambers on rotation angle at different rotary speeds and on different inlet pressures and relationship between pumping speed and inlet pressure are obtained.The comparison between calculated values and experimental data obtained for one‐stage claw pump with identical rotors is carried out. The maximal difference between the calculated and experimental values does not exceed 15 %. The developed mathematical model is recommended for analysis of influence of rotors geometry on the working process parameters and pumping characteristics of an oil free claw pump.
- 3 April 2017
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 29 (2) , 45-49
The working process of an oil‐free claw vacuum pump
Mathematical model of oil free claw vacuum pump is presented. The model is based on energy balance differential equations of thermodynamic system of variable mass working body.Using the equations of coordinates transformation and contact line of rotors continuity condition, equations for geometry of claw pump working chamber on condition of rotors point connection are obtained. To evaluate the leakage through the rotor mechanism channels, their existence graphs are plotted and geometric parameters of the channels depending on rotors position are determined.As a result of modeling, dependence of pressure and temperature in suction and compression‐discharge chambers on rotation angle at different rotary speeds and on different inlet pressures and relationship between pumping speed and inlet pressure are obtained.The comparison between calculated values and experimental data obtained for one‐stage claw pump with identical rotors is carried out. The maximal difference between the calculated and experimental values does not exceed 15 %. The developed mathematical model is recommended for analysis of influence of rotors geometry on the working process parameters and pumping characteristics of an oil free claw pump.
- 1 June 2016
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 28 (3) , 43-47
Experimental Study of Oil‐Free Claw Vacuum Pump Characteristics
Experimental study of pumping characteristics of a pilot model of a claw single‐stage vacuum pump with identical rotors was carried out. The curves of pumping speed vs. pressure at different rotary speed and the ultimate pressure at different rotors speed were determined on a test unit. Indicator pressure diagrams in working chambers of claw vacuum pump were obtained with the help of special sensors.Thus, an experimental data bank concerning the pumping characteristics of claw vacuum pump was created. It may be used for estimation of mathematical model adequacy and further development of the pump design.
- 1 June 2016
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 28 (3) , 43-47
Experimental Study of Oil‐Free Claw Vacuum Pump Characteristics
Experimental study of pumping characteristics of a pilot model of a claw single‐stage vacuum pump with identical rotors was carried out. The curves of pumping speed vs. pressure at different rotary speed and the ultimate pressure at different rotors speed were determined on a test unit. Indicator pressure diagrams in working chambers of claw vacuum pump were obtained with the help of special sensors.Thus, an experimental data bank concerning the pumping characteristics of claw vacuum pump was created. It may be used for estimation of mathematical model adequacy and further development of the pump design.
- 12 June 2015
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 27 (3) , 42-46
Deformations of Working Elements in Oil Free Scroll Vacuum Pumps
- 12 June 2015
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 27 (3) , 42-46
Deformations of Working Elements in Oil Free Scroll Vacuum Pumps
- 9 February 2015
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 27 (1) , 36-40
Conductance Calculation Of Slot Channels with Variable Cross Section
The range of operation pressures of non‐contact vacuum pumps may reach six decades, and flow regime in slot channels of the rotor mechanism may vary from molecular flow to viscous flow. This article is a continuation of a series of authors‘ publications dedicated to the development of a method which makes it possible to calculate promptly the conductance of slot channels with complex contoured geometry with the minimal clearance at a certain point along gas flow direction for all three gas flow regimes: molecular, transient and viscous.The numerical solution of the differential equations system (equations of motion, energy, continuity and state) is used for calculation of mass flow rate in transient gas flow regime. On the basis of the numerical calculation results the relationship is obtained which represents a smooth joining of the data for molecular and viscous flow regimes.Verification of the model and the obtained relationship is carried out by comparison of numerical calculation results of gas mass flow rate and conductance with experimental data obtained by blowing‐through of slot channels. The maximal deviation of calculation according to the obtained relationship from the experiment does not exceed 14%, the average uncertainty being less than 8%, which makes it possible to recommend it for practical application in transient flow regime.
- 9 February 2015
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 27 (1) , 36-40
Conductance Calculation Of Slot Channels with Variable Cross Section
The range of operation pressures of non‐contact vacuum pumps may reach six decades, and flow regime in slot channels of the rotor mechanism may vary from molecular flow to viscous flow. This article is a continuation of a series of authors‘ publications dedicated to the development of a method which makes it possible to calculate promptly the conductance of slot channels with complex contoured geometry with the minimal clearance at a certain point along gas flow direction for all three gas flow regimes: molecular, transient and viscous.The numerical solution of the differential equations system (equations of motion, energy, continuity and state) is used for calculation of mass flow rate in transient gas flow regime. On the basis of the numerical calculation results the relationship is obtained which represents a smooth joining of the data for molecular and viscous flow regimes.Verification of the model and the obtained relationship is carried out by comparison of numerical calculation results of gas mass flow rate and conductance with experimental data obtained by blowing‐through of slot channels. The maximal deviation of calculation according to the obtained relationship from the experiment does not exceed 14%, the average uncertainty being less than 8%, which makes it possible to recommend it for practical application in transient flow regime.
- 3 February 2014
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 26 (1) , 40-44
Non‐contact vacuum pumps
Non‐contact oil‐free vacuum pumps are widely used in different technological processes such as nanomaterials industry, pharmaceuticals industry, food industry, medicine, etc., thanks to absence of oil seal, high discharge, long operating life, yet low energy consumption. Scroll pumps are of particular interest as they make it possible to isolate bearing assemblies with grease from the working volume of the pump with the help of bellows.Pumping characteristics of non‐contact vacuum pumps are greatly influenced by backward leakage through slot channels of the rotor mechanism. The conductance is the main value characterizing backward leakage. In this paper an efficient method for prompt conductance calculation of slot channels with any geometry with the minimal clearance at a certain point along gas flow direction is presented. The calculation error of the presented method does not exceed 6%.The presented method was used in mathematical models for the pumping process of scroll pumps, claw pumps and Roots pumps. This method is recommended for pumping characteristics calculation of different non‐contact pumps and gas flow rates in vacuum systems channels.
- 3 February 2014
- Published by Wiley in Vakuum in Forschung und Praxis
- Vol. 26 (1) , 40-44
Non‐contact vacuum pumps
Non‐contact oil‐free vacuum pumps are widely used in different technological processes such as nanomaterials industry, pharmaceuticals industry, food industry, medicine, etc., thanks to absence of oil seal, high discharge, long operating life, yet low energy consumption. Scroll pumps are of particular interest as they make it possible to isolate bearing assemblies with grease from the working volume of the pump with the help of bellows.Pumping characteristics of non‐contact vacuum pumps are greatly influenced by backward leakage through slot channels of the rotor mechanism. The conductance is the main value characterizing backward leakage. In this paper an efficient method for prompt conductance calculation of slot channels with any geometry with the minimal clearance at a certain point along gas flow direction is presented. The calculation error of the presented method does not exceed 6%.The presented method was used in mathematical models for the pumping process of scroll pumps, claw pumps and Roots pumps. This method is recommended for pumping characteristics calculation of different non‐contact pumps and gas flow rates in vacuum systems channels.