Scott B. Nokleby
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Scott B. Nokleby has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jorge Angeles
Centre for Intelligent Machines, McGill University Emeritus Department of Mechanical Engineering 817, Sherbrooke Street West
3 shared publications - Edward J. Waller
Ontario Tech University
2 shared publications Florentin von Frankenberg
Mechatronic and Robotic Systems Laboratory, University of Ontario Institute of Technology, Oshawa, ON L1H 7K4, Canada
2 shared publications- Ron P. Podhorodeski
Robotics and Mechanisms Laboratory, Department of Mechanical Engineering, University of Victoria, P. O. Box 3055, Victoria, B. C, V8W 3P6, Canada
2 shared publications - Alexei Morozov
JITECH Inc., Pointe Claire, QC, H3A 2T5, Canada
1 shared publication - Alp Zibil
Robotics and Mechanisms Laboratory, Department of Mechanical Engineering, University of Victoria, P. O. Box 3055, Victoria, B. C, V8W 3P6, Canada
1 shared publication
Latest Publications
- 27 September 2024
- Published by Wiley in Journal of Autonomous Vehicles and Systems
- Vol. 4 (4) , 1-15
Effective Map Merging for Long-Term Autonomous Navigation
An algorithm is presented that intelligently merges multiple 3D point clouds used for localization based on when the point cloud was recorded to create an updated map that is more similar to the current environment. The algorithm was implemented on a Boston Dynamics Spot robot and was used to upgrade Spot’s autonomous navigation algorithm called Autowalk by adding the capability for long-term navigation in semi-static environments. The proposed algorithm was validated by having Spot navigate both indoor and outdoor environments over multiple months traveling over 43 km autonomously without losing localization. The proposed method extends the life of programmed autonomous missions to ensure a robot can be used over extended periods of time without the need to re-teach these autonomous missions due to changes in the environment.
- 27 September 2024
- Published by Wiley in Journal of Autonomous Vehicles and Systems
- Vol. 4 (4) , 1-15
Effective Map Merging for Long-Term Autonomous Navigation
An algorithm is presented that intelligently merges multiple 3D point clouds used for localization based on when the point cloud was recorded to create an updated map that is more similar to the current environment. The algorithm was implemented on a Boston Dynamics Spot robot and was used to upgrade Spot’s autonomous navigation algorithm called Autowalk by adding the capability for long-term navigation in semi-static environments. The proposed algorithm was validated by having Spot navigate both indoor and outdoor environments over multiple months traveling over 43 km autonomously without losing localization. The proposed method extends the life of programmed autonomous missions to ensure a robot can be used over extended periods of time without the need to re-teach these autonomous missions due to changes in the environment.
- 5 July 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 13 (6) , 1-13
Computation of the Available Force Set of a 3-RPRR Kinematically Redundant Planar Parallel Manipulator
An algorithm is developed to determine the available force set (AFS) of the 3-RPRR kinematically redundant planar parallel manipulator. The results of the algorithm are verified against a brute force approach and are found to yield exact results with significantly less computational time. The use of the AFS in a robot design context is illustrated through the analysis of two performance indices: the maximum pure force capable of being applied in any direction and the maximum pure force capable of being applied in a given direction. The algorithm is used to compute the AFS and the performance indices throughout the 3-RPRR robot’s workspace. The proposed methodology is a useful tool for the design and analysis of the 3-RPRR robot and could be adapted to other kinematically redundant planar parallel manipulators.
- 5 July 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 13 (6) , 1-13
Computation of the Available Force Set of a 3-RPRR Kinematically Redundant Planar Parallel Manipulator
An algorithm is developed to determine the available force set (AFS) of the 3-RPRR kinematically redundant planar parallel manipulator. The results of the algorithm are verified against a brute force approach and are found to yield exact results with significantly less computational time. The use of the AFS in a robot design context is illustrated through the analysis of two performance indices: the maximum pure force capable of being applied in any direction and the maximum pure force capable of being applied in a given direction. The algorithm is used to compute the AFS and the performance indices throughout the 3-RPRR robot’s workspace. The proposed methodology is a useful tool for the design and analysis of the 3-RPRR robot and could be adapted to other kinematically redundant planar parallel manipulators.
- 5 March 2018
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 4 (2)
Probabilistic-Based Robotic Radiation Mapping Using Sparse Data
This paper presents a novel methodology for generating radiation intensity maps using a mobile robotic platform and an integrated radiation model. The radiation intensity mapping approach consists of two stages. First, radiation intensity samples are collected using a radiation sensor mounted on a mobile robotic platform, reducing the risk of exposure to humans from an unknown radiation field. Next, these samples, which need only to be taken from a subsection of the entire area being mapped, are then used to calibrate a radiation model of the area. This model is then used to predict the radiation intensity field throughout the rest of the area that could not be directly measured. The performance of the approach is evaluated through experiments. The results show that the developed system is effective at achieving the goal of generating radiation maps using sparse data.
- 5 March 2018
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 4 (2)
Probabilistic-Based Robotic Radiation Mapping Using Sparse Data
This paper presents a novel methodology for generating radiation intensity maps using a mobile robotic platform and an integrated radiation model. The radiation intensity mapping approach consists of two stages. First, radiation intensity samples are collected using a radiation sensor mounted on a mobile robotic platform, reducing the risk of exposure to humans from an unknown radiation field. Next, these samples, which need only to be taken from a subsection of the entire area being mapped, are then used to calibrate a radiation model of the area. This model is then used to predict the radiation intensity field throughout the rest of the area that could not be directly measured. The performance of the approach is evaluated through experiments. The results show that the developed system is effective at achieving the goal of generating radiation maps using sparse data.
- 1 March 2018
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 42 (1) , 61-70
Inclined landing testing of an omni-directional unmanned aerial vehicle
Traditional multi-rotors and helicopters control translational movement by changing the orientation of the entire vehicle. This approach limits the effectiveness of these vehicles in applications — such as a mobile manipulator base — in which it is often necessary to fly near large structures where unpredictable aerodynamic conditions exist. Maintaining precise control of position requires counteracting disturbance forces quickly. Having to roll and pitch the entire vehicle induces a delay that limits the ability of traditional multi-rotors and helicopters to maintain position precisely. Additionally, a mobile base must be capable of resisting arbitrary combinations of force and torque resulting from use of a manipulator arm. Traditional multi-rotors and helicopters do not have this ability. This paper presents a novel unmanned aerial vehicle (UAV) concept that features the addition of four rotors orthogonal to the main lift rotors of a traditional quadrotor design. These rotors allow decoupling of orientation from translational movement. Tests done on a physical prototype demonstrated the ability to sustain roll or pitch angles up to 15° independent of translational movement, including the ability to move backwards at an angle and to dock on inclined surfaces in a controlled manner. The tests show that the OmniCopter can successfully land on surfaces with up to 30° inclination. This type of motion is impossible for a traditional multi-rotor vehicle.
- 1 March 2018
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 42 (1) , 61-70
Inclined landing testing of an omni-directional unmanned aerial vehicle
Traditional multi-rotors and helicopters control translational movement by changing the orientation of the entire vehicle. This approach limits the effectiveness of these vehicles in applications — such as a mobile manipulator base — in which it is often necessary to fly near large structures where unpredictable aerodynamic conditions exist. Maintaining precise control of position requires counteracting disturbance forces quickly. Having to roll and pitch the entire vehicle induces a delay that limits the ability of traditional multi-rotors and helicopters to maintain position precisely. Additionally, a mobile base must be capable of resisting arbitrary combinations of force and torque resulting from use of a manipulator arm. Traditional multi-rotors and helicopters do not have this ability. This paper presents a novel unmanned aerial vehicle (UAV) concept that features the addition of four rotors orthogonal to the main lift rotors of a traditional quadrotor design. These rotors allow decoupling of orientation from translational movement. Tests done on a physical prototype demonstrated the ability to sustain roll or pitch angles up to 15° independent of translational movement, including the ability to move backwards at an angle and to dock on inclined surfaces in a controlled manner. The tests show that the OmniCopter can successfully land on surfaces with up to 30° inclination. This type of motion is impossible for a traditional multi-rotor vehicle.
- 25 May 2017
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 3 (3) , 034502
MCNP Simulation of In-Core Dose Rates for an Offline CANDU® Reactor
Inspections of pressure tubes in CANDU® reactors are a key part of maintaining safe operating conditions. The current inspection system, the channel inspection and gauging apparatus for reactors (CIGAR), performs the job well but is limited by the fact that it can only inspect one channel at a time. A multidisciplinary team is currently developing a novel robotic inspection system. As part of this work, a Monte Carlo N-particle (MCNP) model has been developed in order to predict the dose rates that the improved inspection system will be exposed to and, from this, predict the component lifetime. This MCNP model will be capable of predicting in-core dose rates at any location within the reactor, and as such could be used for other situations where the in-core dose rate needs to be known. Based on estimates from this model, it is expected that at 7 days after shutdown, the improved inspection system could survive in core for approximately 7 h, providing it uses a tungsten shield 2.5 cm in thickness around the integrated circuit components. This is expected to be sufficient to perform a single inspection.
- 25 May 2017
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 3 (3) , 034502
MCNP Simulation of In-Core Dose Rates for an Offline CANDU® Reactor
Inspections of pressure tubes in CANDU® reactors are a key part of maintaining safe operating conditions. The current inspection system, the channel inspection and gauging apparatus for reactors (CIGAR), performs the job well but is limited by the fact that it can only inspect one channel at a time. A multidisciplinary team is currently developing a novel robotic inspection system. As part of this work, a Monte Carlo N-particle (MCNP) model has been developed in order to predict the dose rates that the improved inspection system will be exposed to and, from this, predict the component lifetime. This MCNP model will be capable of predicting in-core dose rates at any location within the reactor, and as such could be used for other situations where the in-core dose rate needs to be known. Based on estimates from this model, it is expected that at 7 days after shutdown, the improved inspection system could survive in core for approximately 7 h, providing it uses a tungsten shield 2.5 cm in thickness around the integrated circuit components. This is expected to be sufficient to perform a single inspection.
- 8 August 2016
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 35 (8) , 1773-1792
An automatic switching approach to teleoperation of mobile-manipulator systems using virtual fixtures
SUMMARY: This work presents a novel command strategy developed to improve operator performance and minimize difficulties in teleoperation tasks for mobile-manipulator systems with a holonomic base. Aimed specifically at novice operators, virtual fixtures are introduced as a means to minimize collisions and assist in navigation. Using the 6-degree-of-freedom (DOF) Omnibot mobile-manipulator system (MMS), a command strategy is implemented such that the operator need only control a 3-DOF haptic joystick to achieve full control of the Omnibot MMS. The command strategy is used to coordinate control between the arm and the base of the system, prevent collisions with known obstacles, and alert the operator of proximity to those obstacles with haptic forces. Through experimental testing it is shown that operator performance improved with the use of virtual fixtures.
- 8 August 2016
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 35 (8) , 1773-1792
An automatic switching approach to teleoperation of mobile-manipulator systems using virtual fixtures
SUMMARY: This work presents a novel command strategy developed to improve operator performance and minimize difficulties in teleoperation tasks for mobile-manipulator systems with a holonomic base. Aimed specifically at novice operators, virtual fixtures are introduced as a means to minimize collisions and assist in navigation. Using the 6-degree-of-freedom (DOF) Omnibot mobile-manipulator system (MMS), a command strategy is implemented such that the operator need only control a 3-DOF haptic joystick to achieve full control of the Omnibot MMS. The command strategy is used to coordinate control between the arm and the base of the system, prevent collisions with known obstacles, and alert the operator of proximity to those obstacles with haptic forces. Through experimental testing it is shown that operator performance improved with the use of virtual fixtures.
- 17 June 2016
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 2 (3) , 031020
Design and Implementation of an Automated Gamma Probe for Jet Boring Uranium Mining
A proof-of-concept detector prototype capable of collecting and storing radiometric data in the jet boring system (JBS) during pilot hole drilling at the Cigar Lake uranium mine is presented. Cigar Lake is the world’s second highest known grade uranium mine and is located in northern Saskatchewan, Canada. Variant design is used to design, develop, test, and implement the detector’s firmware, software, and hardware. The battery-powered detector is attached inside a JBS drill rod to collect radiometric data through the drilling cycle. A readout box is used to initiate the detector, recharge the battery, and download radiometric data after the pilot hole drilling cycle is complete. Functional testing results are presented, and comparative test results between the JBS gamma probe and the AlphaNUCLEAR Hi-Flux probe are evaluated. Field data collected from a pilot hole are plotted against the pilot hole’s driving layout and jetting recipe to show the accuracy of the readings collected.
- 17 June 2016
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 2 (3) , 031020
Design and Implementation of an Automated Gamma Probe for Jet Boring Uranium Mining
A proof-of-concept detector prototype capable of collecting and storing radiometric data in the jet boring system (JBS) during pilot hole drilling at the Cigar Lake uranium mine is presented. Cigar Lake is the world’s second highest known grade uranium mine and is located in northern Saskatchewan, Canada. Variant design is used to design, develop, test, and implement the detector’s firmware, software, and hardware. The battery-powered detector is attached inside a JBS drill rod to collect radiometric data through the drilling cycle. A readout box is used to initiate the detector, recharge the battery, and download radiometric data after the pilot hole drilling cycle is complete. Functional testing results are presented, and comparative test results between the JBS gamma probe and the AlphaNUCLEAR Hi-Flux probe are evaluated. Field data collected from a pilot hole are plotted against the pilot hole’s driving layout and jetting recipe to show the accuracy of the readings collected.
- 1 June 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (2) , 169-190
DESIGN AND DEVELOPMENT OF AN AUTONOMOUS OMNIDIRECTIONAL HAZARDOUS MATERIALS HANDLING ROBOT
This paper describes the design and testing of an autonomous omnidirectional robot to be used for moving radioactive materials while minimizing human exposure. The robot, called the OmniMaxbot, uses the Robot Operating System (ROS) to allow the individual components to communicate as well as to control the movement. Details about the hardware and software used in the OmniMaxbot are explained. Test results are presented for the navigation system based on the ROS packages: Global Planner, Base Local Planner, and Adaptive Monte Carlo Localization (AMCL). The test results confirm that the OmniMaxbot is capable of autonomously navigating to a mock ash can, lifting it, navigating to a drop-off location, putting the mock ash can down, backing away until the forks are clear of the mock ash can, and navigating to a standby location. These actions can be performed in areas with both static and dynamic obstacles.
- 1 June 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (2) , 169-190
DESIGN AND DEVELOPMENT OF AN AUTONOMOUS OMNIDIRECTIONAL HAZARDOUS MATERIALS HANDLING ROBOT
This paper describes the design and testing of an autonomous omnidirectional robot to be used for moving radioactive materials while minimizing human exposure. The robot, called the OmniMaxbot, uses the Robot Operating System (ROS) to allow the individual components to communicate as well as to control the movement. Details about the hardware and software used in the OmniMaxbot are explained. Test results are presented for the navigation system based on the ROS packages: Global Planner, Base Local Planner, and Adaptive Monte Carlo Localization (AMCL). The test results confirm that the OmniMaxbot is capable of autonomously navigating to a mock ash can, lifting it, navigating to a drop-off location, putting the mock ash can down, backing away until the forks are clear of the mock ash can, and navigating to a standby location. These actions can be performed in areas with both static and dynamic obstacles.
- 1 December 2013
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 37 (4) , 1043-1056
INDOOR LOCALIZATION OF AN OMNI-DIRECTIONAL WHEELED MOBILE ROBOT
This paper presents a localization system developed for estimating the pose, i.e., position and orientation, of an omni-directional wheeled mobile robot operating in indoor structured environments. The developed system uses a combination of relative and absolute localization methods for pose estimation. Odometry serves as the relative localization method providing pose estimates through the integration of measurements obtained from shaft encoders on the robot’s drive motors. Absolute localization is achieved with a novel GPS-like system that performs localization of active beacons mounted on the mobile robot based on distance measurements to receivers fixed at known positions in the robot’s indoor workspace. A simple data fusion algorithm is used in the localization system to combine the pose estimates from the two localization methods and achieve improved performance. Experimental results demonstrating the performance of the developed system at localizing the omni-directional robot in an indoor environment are presented.
- 1 December 2013
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 37 (4) , 1043-1056
INDOOR LOCALIZATION OF AN OMNI-DIRECTIONAL WHEELED MOBILE ROBOT
This paper presents a localization system developed for estimating the pose, i.e., position and orientation, of an omni-directional wheeled mobile robot operating in indoor structured environments. The developed system uses a combination of relative and absolute localization methods for pose estimation. Odometry serves as the relative localization method providing pose estimates through the integration of measurements obtained from shaft encoders on the robot’s drive motors. Absolute localization is achieved with a novel GPS-like system that performs localization of active beacons mounted on the mobile robot based on distance measurements to receivers fixed at known positions in the robot’s indoor workspace. A simple data fusion algorithm is used in the localization system to combine the pose estimates from the two localization methods and achieve improved performance. Experimental results demonstrating the performance of the developed system at localizing the omni-directional robot in an indoor environment are presented.
- 7 June 2012
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 31 (3) , 331-344
A Methodology for tele-operating mobile manipulators with an emphasis on operator ease of use
SUMMARY An algorithm for the tele-operation of mobile-manipulator systems with a focus on ease of use for the operator is presented. The algorithm allows for unified, intuitive, and coordinated control of mobile manipulators. It consists of three states. In the first state, a single 6-degrees-of-freedom (DOF) joystick is used to control the manipulator's position and orientation. The second state occurs when the manipulator approaches a singular configuration, resulting in the mobile base moving in a manner so as to keep the end-effector travelling in its last direction of motion. This is done through the use of a constrained optimization routine. The third state is entered when the operator returns the joystick to the home position. Both the mobile base and manipulator move with respect to one another keeping the end-effector stationary and placing the manipulator into an ideal configuration. The algorithm has been implemented on an 8-DOF mobile manipulator and the test results show that it is effective at moving the system in an intuitive manner.
- 7 June 2012
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 31 (3) , 331-344
A Methodology for tele-operating mobile manipulators with an emphasis on operator ease of use
SUMMARY An algorithm for the tele-operation of mobile-manipulator systems with a focus on ease of use for the operator is presented. The algorithm allows for unified, intuitive, and coordinated control of mobile manipulators. It consists of three states. In the first state, a single 6-degrees-of-freedom (DOF) joystick is used to control the manipulator's position and orientation. The second state occurs when the manipulator approaches a singular configuration, resulting in the mobile base moving in a manner so as to keep the end-effector travelling in its last direction of motion. This is done through the use of a constrained optimization routine. The third state is entered when the operator returns the joystick to the home position. Both the mobile base and manipulator move with respect to one another keeping the end-effector stationary and placing the manipulator into an ideal configuration. The algorithm has been implemented on an 8-DOF mobile manipulator and the test results show that it is effective at moving the system in an intuitive manner.