Hassan Mahfuz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hassan Mahfuz has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Shaik Jeelani
Tuskegee University’s Center for Advanced Materials (T-CAM)
9 shared publicationsVijaya K. Rangari
Tuskegee University's Center for Advanced Materials (T-CAM), Tuskegee, Alabama 36088, USA
4 shared publicationsMartin R. Parker
University of South Alabama
2 shared publicationsMohammad M. Hasan
Tuskegee University's Center for Advanced Material (T-CAM), Tuskegee, AL 36088, USA
2 shared publicationsNathaniel Chisholm
Center for Advanced Materials (T-CAM), Tuskegee University, Tuskegee, Alabama 36088, USA
2 shared publicationsReneé M. Rodgers
Center for Advanced Materials (T-CAM), Tuskegee University, Tuskegee, Alabama 36088, USA
2 shared publications
Latest Publications
- 15 March 2009
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 105 (6) , 064307
Enhanced stab resistance of armor composites with functionalized silica nanoparticles
Traditionally shear thickening fluid (STF) reinforced with Kevlar has been used to develop flexible armor. At the core of the STF-Kevlar composites is a mixture of polyethylene glycol (PEG) and silica particles. This mixture is often known as STF and is consisted of approximately 45 wt % PEG and 55 wt % silica. During rheological tests, STF shows instantaneous spike in viscosity above a critical shear rate. Fabrication of STF-Kevlar composites requires preparation of STF, dilution with ethanol, and then impregnation with Kevlar. In the current approach, nanoscale silica particles were dispersed directly into a mixture of PEG and ethanol through a sonic cavitation process. Two types of silica nanoparticles were used in the investigation: 30 nm crystalline silica and 7 nm amorphous silica. The admixture was then reinforced with Kevlar fabric to produce flexible armor composites. In the next step, silica particles are functionalized with a silane coupling agent to enhance bonding between silica and PEG. The performance of the resulting armor composites improved significantly. As evidenced by National Institute of Justice spike tests, the energy required for zero-layer penetration (i.e., no penetration) jumped twofold: from 12 to 25 J cm2/g. The source of this improvement has been traced to the formation of siloxane (Si-O-Si) bonds between silica and PEG and superior coating of Kevlar filaments with particles. Fourier transform infrared, x-ray photoemission spectroscopy, and scanning electron microscopy studies were performed to examine chemical bonds, elemental composition, and particle dispersion responsible for such improvement. In summary, our experiments have demonstrated that functionalization of silica particles followed by direct dispersion into PEG resulted in superior Kevlar composites having much higher spike resistance.
- 15 March 2009
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 105 (6) , 064307
Enhanced stab resistance of armor composites with functionalized silica nanoparticles
Traditionally shear thickening fluid (STF) reinforced with Kevlar has been used to develop flexible armor. At the core of the STF-Kevlar composites is a mixture of polyethylene glycol (PEG) and silica particles. This mixture is often known as STF and is consisted of approximately 45 wt % PEG and 55 wt % silica. During rheological tests, STF shows instantaneous spike in viscosity above a critical shear rate. Fabrication of STF-Kevlar composites requires preparation of STF, dilution with ethanol, and then impregnation with Kevlar. In the current approach, nanoscale silica particles were dispersed directly into a mixture of PEG and ethanol through a sonic cavitation process. Two types of silica nanoparticles were used in the investigation: 30 nm crystalline silica and 7 nm amorphous silica. The admixture was then reinforced with Kevlar fabric to produce flexible armor composites. In the next step, silica particles are functionalized with a silane coupling agent to enhance bonding between silica and PEG. The performance of the resulting armor composites improved significantly. As evidenced by National Institute of Justice spike tests, the energy required for zero-layer penetration (i.e., no penetration) jumped twofold: from 12 to 25 J cm2/g. The source of this improvement has been traced to the formation of siloxane (Si-O-Si) bonds between silica and PEG and superior coating of Kevlar filaments with particles. Fourier transform infrared, x-ray photoemission spectroscopy, and scanning electron microscopy studies were performed to examine chemical bonds, elemental composition, and particle dispersion responsible for such improvement. In summary, our experiments have demonstrated that functionalization of silica particles followed by direct dispersion into PEG resulted in superior Kevlar composites having much higher spike resistance.
- 23 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (4) , 1113-1120
Reinforcement of SC-15 epoxy with CNT/CNF under high magnetic field: an investigation of mechanical and thermal response
- 23 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (4) , 1113-1120
Reinforcement of SC-15 epoxy with CNT/CNF under high magnetic field: an investigation of mechanical and thermal response
- 31 May 2007
- Published by Elsevier in Materials Letters
- Vol. 61 (11-12) , 2535-2539
Enhancement of strength and stiffness of epoxy-based composites using nanoparticle infusion and high magnetic fields
- 31 May 2007
- Published by Elsevier in Materials Letters
- Vol. 61 (11-12) , 2535-2539
Enhancement of strength and stiffness of epoxy-based composites using nanoparticle infusion and high magnetic fields
- 11 April 2007
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 292 (4) , 437-444
Reinforcement of Nylon‐6 Filaments with SiO2 Nanoparticles and Comparison of Young's Modulus with Theoretical Bounds
Spherical silica nanoparticles were infused into nylon‐6 and drawn into filaments through a melt‐extrusion process. The idea was to improve the strength and stiffness of the resulting filaments by utilizing the interactions between the nanoparticles and the polymer. The focus was to increase the fracture strain of the filaments, as this had not been possible earlier with the infusion of carbon nanotubes. It has been observed that with the infusion of silica nanoparticles, the strength and Young's modulus of the nylon filament can be enhanced in the 28 to 36% range without any loss of fracture strain. The source of this improvement has been traced to the formation of stronger amide and carbonyl bonds, nucleated by the presence of SiO2 nanoparticles during polymerization. Moreover, calculations based on basic theories of inclusions show that the Young's modulus of the nanophased filament is within 5% of the upper bound predicted by the micromechanical theory. magnified image
- 11 April 2007
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 292 (4) , 437-444
Reinforcement of Nylon‐6 Filaments with SiO2 Nanoparticles and Comparison of Young's Modulus with Theoretical Bounds
Spherical silica nanoparticles were infused into nylon‐6 and drawn into filaments through a melt‐extrusion process. The idea was to improve the strength and stiffness of the resulting filaments by utilizing the interactions between the nanoparticles and the polymer. The focus was to increase the fracture strain of the filaments, as this had not been possible earlier with the infusion of carbon nanotubes. It has been observed that with the infusion of silica nanoparticles, the strength and Young's modulus of the nylon filament can be enhanced in the 28 to 36% range without any loss of fracture strain. The source of this improvement has been traced to the formation of stronger amide and carbonyl bonds, nucleated by the presence of SiO2 nanoparticles during polymerization. Moreover, calculations based on basic theories of inclusions show that the Young's modulus of the nanophased filament is within 5% of the upper bound predicted by the micromechanical theory. magnified image
- 20 February 2006
- Published by AIP Publishing in Applied Physics Letters
- Vol. 88 (8) , 083119
Enhancement of strength and stiffness of Nylon 6 filaments through carbon nanotubes reinforcement
We report a method to fabricate carbon nanotube reinforced Nylon filaments through an extrusion process. In this process, Nylon 6 and multiwalled carbon nanotubes (MWCNT) are first dry mixed and then extruded in the form of continuous filaments by a single screw extrusion method. Thermo gravimetric analysis (TGA) and differential scanning calorimetry (DSC) studies have indicated that there is a moderate increase in Tg without a discernible shift in the melting endotherm. Tensile tests on single filaments have demonstrated that Young’s modulus and strength of the nanophased filaments have increased by 220% and 164%, respectively with the addition of only 1wt.% MWCNTs. SEM studies and micromechanics based calculations have shown that the alignment of MWCNTs in the filaments, and high interfacial shear strength between the matrix and the nanotube reinforcement was responsible for such a dramatic improvement in properties.
- 20 February 2006
- Published by AIP Publishing in Applied Physics Letters
- Vol. 88 (8) , 083119
Enhancement of strength and stiffness of Nylon 6 filaments through carbon nanotubes reinforcement
We report a method to fabricate carbon nanotube reinforced Nylon filaments through an extrusion process. In this process, Nylon 6 and multiwalled carbon nanotubes (MWCNT) are first dry mixed and then extruded in the form of continuous filaments by a single screw extrusion method. Thermo gravimetric analysis (TGA) and differential scanning calorimetry (DSC) studies have indicated that there is a moderate increase in Tg without a discernible shift in the melting endotherm. Tensile tests on single filaments have demonstrated that Young’s modulus and strength of the nanophased filaments have increased by 220% and 164%, respectively with the addition of only 1wt.% MWCNTs. SEM studies and micromechanics based calculations have shown that the alignment of MWCNTs in the filaments, and high interfacial shear strength between the matrix and the nanotube reinforcement was responsible for such a dramatic improvement in properties.
- Open Access
- 23 May 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 290 (5) , 417
Cover: Macromol. Mater. Eng. 5/2005
Cover: The picture on the cover shows the crack formation in epoxy (or polymer) nanocomposites. Further details can be found in the Full Paper by R. M. Rodgers, H. Mahfuz,* V. K. Rangari, N. Chisholm, and S. Jeelani on page 423.
- 23 May 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 290 (5) , 417
Open AccessCover: Macromol. Mater. Eng. 5/2005
Cover: The picture on the cover shows the crack formation in epoxy (or polymer) nanocomposites. Further details can be found in the Full Paper by R. M. Rodgers, H. Mahfuz,* V. K. Rangari, N. Chisholm, and S. Jeelani on page 423.
- 18 May 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 290 (5) , 423-429
Infusion of SiC Nanoparticles Into SC‐15 Epoxy: An Investigation of Thermal and Mechanical Response
Summary: In the present investigation we have developed a novel technique to synthesize nanocomposite materials consisting of SC‐15 epoxy resin and silicon carbide (β‐SiC) nanoparticles. A high intensity ultrasonic liquid processor was used to obtain a homogeneous molecular mixture of epoxy resin and β‐SiC nanoparticles. In this study, we have prepared three different samples containing 0.5, 1, and 1.5% of β‐SiC nanoparticles by weight of the epoxy resin. In parallel, control samples were also made following identical procedures without the infusion of nanoparticles. Test samples were characterized by TGA, DSC and three‐point bend flexural tests to evaluate thermal and mechanical properties. The results indicate that 1 wt.‐% loading derives the maximum improvement in both thermal and mechanical properties when compared to the neat system. The dispersion of nanoparticles and morphological changes were studied by field emission scanning electron microscopy (FE‐SEM) and high resolution transmission electron microscopy (TEM). These results demonstrate that the nanoparticles are spherical in shape (≈30 nm sizes) and are uniformly dispersed over the entire volume of the resin. FE‐SEM micrograph of the plasma etched 1 wt.‐% SiC‐epoxy system. magnified image FE‐SEM micrograph of the plasma etched 1 wt.‐% SiC‐epoxy system.
- 18 May 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 290 (5) , 423-429
Infusion of SiC Nanoparticles Into SC‐15 Epoxy: An Investigation of Thermal and Mechanical Response
Summary: In the present investigation we have developed a novel technique to synthesize nanocomposite materials consisting of SC‐15 epoxy resin and silicon carbide (β‐SiC) nanoparticles. A high intensity ultrasonic liquid processor was used to obtain a homogeneous molecular mixture of epoxy resin and β‐SiC nanoparticles. In this study, we have prepared three different samples containing 0.5, 1, and 1.5% of β‐SiC nanoparticles by weight of the epoxy resin. In parallel, control samples were also made following identical procedures without the infusion of nanoparticles. Test samples were characterized by TGA, DSC and three‐point bend flexural tests to evaluate thermal and mechanical properties. The results indicate that 1 wt.‐% loading derives the maximum improvement in both thermal and mechanical properties when compared to the neat system. The dispersion of nanoparticles and morphological changes were studied by field emission scanning electron microscopy (FE‐SEM) and high resolution transmission electron microscopy (TEM). These results demonstrate that the nanoparticles are spherical in shape (≈30 nm sizes) and are uniformly dispersed over the entire volume of the resin. FE‐SEM micrograph of the plasma etched 1 wt.‐% SiC‐epoxy system. magnified image FE‐SEM micrograph of the plasma etched 1 wt.‐% SiC‐epoxy system.
- 1 January 1994
- Published by Wiley
- p. 449-457
Fatigue and Flexural Response of Advanced Carbon-Carbon Composites at Room and Elevated Temperatures
- 1 January 1994
- Published by Wiley
- p. 449-457
Fatigue and Flexural Response of Advanced Carbon-Carbon Composites at Room and Elevated Temperatures
- 1 January 1994
- Published by Wiley
- p. 219-232
Fracture and Flexural Characterization of Monolithic SiC and SiCw/SiC Composites at Room and Elevated Temperatures
- 1 January 1994
- Published by Wiley
- p. 219-232
Fracture and Flexural Characterization of Monolithic SiC and SiCw/SiC Composites at Room and Elevated Temperatures
- 31 May 1992
- Published by Elsevier in Composites Engineering
- Vol. 2 (4) , 239-247
Effect of reinforcement geometry on the mechanical properties of SiCwAl2O3 composites
- 31 May 1992
- Published by Elsevier in Composites Engineering
- Vol. 2 (4) , 239-247
Effect of reinforcement geometry on the mechanical properties of SiCwAl2O3 composites