Gamani Karunasiri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gamani Karunasiri has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Fabio Alves
Department of Physics, Naval Postgraduate School, Monterey, CA 93943, USA
9 shared publications Fabio Alves
Phys., Naval Postgrad. School, 833 Dyer Rd., Monterey, CA 93943
2 shared publications- Justin Ivancic
Department of Physics, Naval Postgraduate School, Monterey, CA 93943, USA
2 shared publications - Renato Rabelo
Department of Physics, Naval Postgraduate School, Monterey, CA 93943, USA
2 shared publications William Swan
Naval Postgraduate School (United States)
2 shared publications- Alberto Espinoza
Department of Physics, Naval Postgraduate School, Monterey, CA 93943, USA
1 shared publication
Latest Publications
- Open Access
Directional Resonant MEMS Acoustic Sensor and Associated Acoustic Vector Sensor
This paper reports on the design, modeling, analysis, and evaluation of a micro-electromechanical systems acoustic sensor and the novel design of an acoustic vector sensor array (AVS) which utilized this acoustic sensor. This research builds upon previous work conducted to develop a small, lightweight, portable system for the detection and location of quiet or distant acoustic sources of interest. This study also reports on the underwater operation of this sensor and AVS. Studies were conducted in the lab and in the field utilizing multiple acoustic sources (e.g., generated tones, gun shots, drones). The sensor operates at resonance, providing for high acoustic sensitivity and a high signal-to-noise ratio (SNR). The sensor demonstrated a maximum SNR of 88 dB with an associated sensitivity of −84.6 dB re 1 V/μPa (59 V/Pa). The sensor design can be adjusted to set a specified resonant frequency to align with a known acoustic signature of interest. The AVS demonstrated an unambiguous, 360-degree, in-plane, azimuthal coverage and was able to provide an acoustic direction of arrival to an average error of within 3.5° during field experiments. The results of this research demonstrate the potential usefulness of this sensor and AVS design for specific applications.
Open AccessDirectional Resonant MEMS Acoustic Sensor and Associated Acoustic Vector Sensor
This paper reports on the design, modeling, analysis, and evaluation of a micro-electromechanical systems acoustic sensor and the novel design of an acoustic vector sensor array (AVS) which utilized this acoustic sensor. This research builds upon previous work conducted to develop a small, lightweight, portable system for the detection and location of quiet or distant acoustic sources of interest. This study also reports on the underwater operation of this sensor and AVS. Studies were conducted in the lab and in the field utilizing multiple acoustic sources (e.g., generated tones, gun shots, drones). The sensor operates at resonance, providing for high acoustic sensitivity and a high signal-to-noise ratio (SNR). The sensor demonstrated a maximum SNR of 88 dB with an associated sensitivity of −84.6 dB re 1 V/μPa (59 V/Pa). The sensor design can be adjusted to set a specified resonant frequency to align with a known acoustic signature of interest. The AVS demonstrated an unambiguous, 360-degree, in-plane, azimuthal coverage and was able to provide an acoustic direction of arrival to an average error of within 3.5° during field experiments. The results of this research demonstrate the potential usefulness of this sensor and AVS design for specific applications.
- 5 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (6) , 1-4
Direction of Arrival Algorithm for Acoustic Sensors Operating Near Resonance
Recently it has been possible to detect sound direction using phase-sensitive sensors placed much closer to each other than the sound wavelength. A typical setup combines two phase-sensitive sensors placed perpendicular to each other with a third omnidirectional sensor, the latter to determine the bearing quadrant. So far, algorithms that extract the sound direction from the sensor voltages have only been applicable to sensors with identical frequency responses. However, we have developed MEMS sensors with simple harmonic oscillator-like resonance behavior for which these algorithms no longer apply. The operation near resonance greatly increases their performance, but the frequency dependences of any two sensors are different from each other and from the omnidirectional sensor. In this letter, we show how to accommodate these differences, first, by forcing the two sensor peaks to conform to each other in both magnitude and phase, and second, by adjusting the phase of the omnidirectional sensor to approximately match the phases of the resonant sensors near their resonant frequencies. We then present two algorithms to extract the sound direction. We lay out the theoretical basis for our algorithms and present measurements of acoustic noise to show the algorithms' effectiveness.
- 5 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (6) , 1-4
Direction of Arrival Algorithm for Acoustic Sensors Operating Near Resonance
Recently it has been possible to detect sound direction using phase-sensitive sensors placed much closer to each other than the sound wavelength. A typical setup combines two phase-sensitive sensors placed perpendicular to each other with a third omnidirectional sensor, the latter to determine the bearing quadrant. So far, algorithms that extract the sound direction from the sensor voltages have only been applicable to sensors with identical frequency responses. However, we have developed MEMS sensors with simple harmonic oscillator-like resonance behavior for which these algorithms no longer apply. The operation near resonance greatly increases their performance, but the frequency dependences of any two sensors are different from each other and from the omnidirectional sensor. In this letter, we show how to accommodate these differences, first, by forcing the two sensor peaks to conform to each other in both magnitude and phase, and second, by adjusting the phase of the omnidirectional sensor to approximately match the phases of the resonant sensors near their resonant frequencies. We then present two algorithms to extract the sound direction. We lay out the theoretical basis for our algorithms and present measurements of acoustic noise to show the algorithms' effectiveness.
- Open Access
Dual Band MEMS Directional Acoustic Sensor for Near Resonance Operation
In this paper, we report on the design and characterization of a microelectromechanical systems (MEMS) directional sensor inspired by the tympana configuration of the parasitic fly Ormia ochracea. The sensor is meant to be operated at resonance and act as a natural filter for the undesirable frequency bands. By means of breaking the symmetry of a pair of coupled bridged membranes, two independent bending vibrational modes can be excited. The electronic output, obtained by the transduction of the vibration to differential capacitance and then voltage through charge amplifiers, can be manipulated to tailor the frequency response of the sensor. Four different frequency characteristics were demonstrated. The sensor exhibits, at resonance, mechanical sensitivity around 6 μm/Pa and electrical sensitivity around 13 V/Pa. The noise was thoroughly characterized, and it was found that the sensor die, rather than the fundamental vibration, induces the predominant part of the noise. The computed average signal-to-noise (SNR) ratio in the pass band is about 91 dB. This result, in combination with an accurate dipole-like directional response, indicates that this type of directional sensor can be designed to exhibit high SNR and selectable frequency responses demanded by different applications.
Open AccessDual Band MEMS Directional Acoustic Sensor for Near Resonance Operation
In this paper, we report on the design and characterization of a microelectromechanical systems (MEMS) directional sensor inspired by the tympana configuration of the parasitic fly Ormia ochracea. The sensor is meant to be operated at resonance and act as a natural filter for the undesirable frequency bands. By means of breaking the symmetry of a pair of coupled bridged membranes, two independent bending vibrational modes can be excited. The electronic output, obtained by the transduction of the vibration to differential capacitance and then voltage through charge amplifiers, can be manipulated to tailor the frequency response of the sensor. Four different frequency characteristics were demonstrated. The sensor exhibits, at resonance, mechanical sensitivity around 6 μm/Pa and electrical sensitivity around 13 V/Pa. The noise was thoroughly characterized, and it was found that the sensor die, rather than the fundamental vibration, induces the predominant part of the noise. The computed average signal-to-noise (SNR) ratio in the pass band is about 91 dB. This result, in combination with an accurate dipole-like directional response, indicates that this type of directional sensor can be designed to exhibit high SNR and selectable frequency responses demanded by different applications.
- Open Access
MEMS Underwater Directional Acoustic Sensor in Near Neutral Buoyancy Configuration
A MEMS directional acoustic sensor housed in an air cavity and operated underwater in a near-neutral buoyancy configuration is demonstrated. The sensor consists of two wings connected by a bridge and attached to a substrate by two centrally mounted torsional legs. The frequency response showed two resonant peaks corresponding to a rocking mode (wings moving in opposite directions) and a bending mode (wings moving in the same direction). Initial tests of the sensor using a shaker table showed that the response is highly dependent on the vibration direction. In air, the sensor showed a maximum sensitivity of about 95 mV/Pa with a cosine directional response. Underwater, the maximum sensitivity was about 37 mV/Pa with a similar cosine directional response. The measured maximum SNR was about 38 dB for a signal generated by a sound stimulus of 1 Pa when the sensor is operated near the bending resonance. The results indicate that this type of MEMS sensor can be operated in a near-neutral buoyant configuration and achieve a good directional response.
Open AccessMEMS Underwater Directional Acoustic Sensor in Near Neutral Buoyancy Configuration
A MEMS directional acoustic sensor housed in an air cavity and operated underwater in a near-neutral buoyancy configuration is demonstrated. The sensor consists of two wings connected by a bridge and attached to a substrate by two centrally mounted torsional legs. The frequency response showed two resonant peaks corresponding to a rocking mode (wings moving in opposite directions) and a bending mode (wings moving in the same direction). Initial tests of the sensor using a shaker table showed that the response is highly dependent on the vibration direction. In air, the sensor showed a maximum sensitivity of about 95 mV/Pa with a cosine directional response. Underwater, the maximum sensitivity was about 37 mV/Pa with a similar cosine directional response. The measured maximum SNR was about 38 dB for a signal generated by a sound stimulus of 1 Pa when the sensor is operated near the bending resonance. The results indicate that this type of MEMS sensor can be operated in a near-neutral buoyant configuration and achieve a good directional response.
- Open Access
Fabrication of MEMS Directional Acoustic Sensors for Underwater Operation
In this work, microelectromechanical systems (MEMS)-based directional acoustic sensors operating in an underwater environment are explored. The studied sensors consist of a free-standing single wing or two wings pivoted to a substrate. The sensors operate in a narrow frequency band determined by the resonant frequency of the mechanical structure. The electronic readout of the mechanical response is obtained using interdigitated comb finger capacitors attached to the wings. The characteristics of MEMS sensors immersed in silicone oil are simulated using finite element modeling. The performance of the sensors is evaluated both in air and underwater. For underwater testing and operation, the sensors are packaged in a housing containing silicone oil, which was specially developed to present near unity acoustic transmission. The measurements show that the resonant frequency of the sensors obtained in air shifts to a lower frequency when immersed in silicone oil, which is primarily due to the mass loading of the liquid. The peak sensitivity of the MEMS sensors is approximately 6 mV/Pa or −165 dB re 1 V/μPa, and the directional response shows a dipole pattern. The signal-to-noise ratio was found to be about 200 or 23 dB at 1 Pa incident sound pressure. The results show the potential of MEMS sensors to be used in underwater applications for sound source localization.
Open AccessFabrication of MEMS Directional Acoustic Sensors for Underwater Operation
In this work, microelectromechanical systems (MEMS)-based directional acoustic sensors operating in an underwater environment are explored. The studied sensors consist of a free-standing single wing or two wings pivoted to a substrate. The sensors operate in a narrow frequency band determined by the resonant frequency of the mechanical structure. The electronic readout of the mechanical response is obtained using interdigitated comb finger capacitors attached to the wings. The characteristics of MEMS sensors immersed in silicone oil are simulated using finite element modeling. The performance of the sensors is evaluated both in air and underwater. For underwater testing and operation, the sensors are packaged in a housing containing silicone oil, which was specially developed to present near unity acoustic transmission. The measurements show that the resonant frequency of the sensors obtained in air shifts to a lower frequency when immersed in silicone oil, which is primarily due to the mass loading of the liquid. The peak sensitivity of the MEMS sensors is approximately 6 mV/Pa or −165 dB re 1 V/μPa, and the directional response shows a dipole pattern. The signal-to-noise ratio was found to be about 200 or 23 dB at 1 Pa incident sound pressure. The results show the potential of MEMS sensors to be used in underwater applications for sound source localization.
- 30 April 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10628, 106280I
Comparison of experimental three-band IR detection of buried objects and multiphysics simulations
A buried-object detection system composed of a LWIR, a MWIR and a SWIR camera, along with a set of ground and ambient temperature sensors was constructed and tested. The objects were buried in a 1.2x1x0.3 m3 sandbox and surface temperature (using LWIR and MWIR cameras) and reflection (using SWIR camera) were recoded throughout the day. Two objects (aluminum and Teflon) with volume of about 2.5x10-4 m3 , were placed at varying depths during the measurements. Ground temperature sensors buried at three different depths measured the vertical temperature profile within the sandbox, while the weather station recorded the ambient temperature and solar radiation intensity. Images from the three cameras were simultaneously acquired in five-minute intervals throughout many days. An algorithm to postprocess and combine the images was developed in order to maximize the probability of detection by identifying thermal anomalies (temperature contrast) resulting from the presence of the buried object in an otherwise homogeneous medium. A simplified detection metric based on contrast differences was established to allow the evaluation of the image processing method. Finite element simulations were performed, reproducing the experiment conditions and, when possible, incorporated with data coming from actual measurements. Comparisons between experiment and simulation results were performed and the simulation parameters were adjusted until images generated from both methods are matched, aiming at obtaining insights of the buried material properties. Preliminary results show a great potential for detection of shallowburied objects such as land mines and IEDs and possible identification using finite element generated maps fitting measured surface maps.
- 30 April 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10628, 106280I
Comparison of experimental three-band IR detection of buried objects and multiphysics simulations
A buried-object detection system composed of a LWIR, a MWIR and a SWIR camera, along with a set of ground and ambient temperature sensors was constructed and tested. The objects were buried in a 1.2x1x0.3 m3 sandbox and surface temperature (using LWIR and MWIR cameras) and reflection (using SWIR camera) were recoded throughout the day. Two objects (aluminum and Teflon) with volume of about 2.5x10-4 m3 , were placed at varying depths during the measurements. Ground temperature sensors buried at three different depths measured the vertical temperature profile within the sandbox, while the weather station recorded the ambient temperature and solar radiation intensity. Images from the three cameras were simultaneously acquired in five-minute intervals throughout many days. An algorithm to postprocess and combine the images was developed in order to maximize the probability of detection by identifying thermal anomalies (temperature contrast) resulting from the presence of the buried object in an otherwise homogeneous medium. A simplified detection metric based on contrast differences was established to allow the evaluation of the image processing method. Finite element simulations were performed, reproducing the experiment conditions and, when possible, incorporated with data coming from actual measurements. Comparisons between experiment and simulation results were performed and the simulation parameters were adjusted until images generated from both methods are matched, aiming at obtaining insights of the buried material properties. Preliminary results show a great potential for detection of shallowburied objects such as land mines and IEDs and possible identification using finite element generated maps fitting measured surface maps.
- 2 June 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10246, 102460
MEMS direction finding acoustic sensor
Conventional directional sound sensing systems employ an array of spatially separated microphones to achieve directivity. However, there are insects such as the Ormia ochracea fly that can determine the direction of sound using a miniature hearing organ much smaller than the wavelength of sound it detects. The fly's eardrums are coupled mechanically with a separation of only 0.5 mm and yet have a remarkable sensitivity to the direction of sound. The MEMS based sensor mimicking the fly’s hearing system was fabricated using an SOI substrate with a 25 μm device layer. The sensor consists of two 1.5 mm x1.6 mm wings connected in the middle by a 2.7 mm x 30 μm bridge. The entire structure is connected to the substrate by two torsional legs at the center. The frequency response of the sensor showed two resonance frequencies at approximately 1.1 kHz (rocking) and 1.5 kHz (bending). The resonance at 1.1 kHz is due to rocking of the wings by twisting the legs and the other at 1.5 kHz is due to bending of the bridge. The response of the sensor was probed electronically using comb finger capacitors integrated to the edges of the wings and with the help of an MS3110 chip. A peak output voltage of about 9V/Pa was measured for sound incident normal to the device at the resonance frequency of the bending mode. The bearing of the incident sound under these conditions could be determined to within a few degrees. These findings indicate the potential use of the MEMS sensor to locate sound sources with high accuracy. © (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- 2 June 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10246, 102460
MEMS direction finding acoustic sensor
Conventional directional sound sensing systems employ an array of spatially separated microphones to achieve directivity. However, there are insects such as the Ormia ochracea fly that can determine the direction of sound using a miniature hearing organ much smaller than the wavelength of sound it detects. The fly's eardrums are coupled mechanically with a separation of only 0.5 mm and yet have a remarkable sensitivity to the direction of sound. The MEMS based sensor mimicking the fly’s hearing system was fabricated using an SOI substrate with a 25 μm device layer. The sensor consists of two 1.5 mm x1.6 mm wings connected in the middle by a 2.7 mm x 30 μm bridge. The entire structure is connected to the substrate by two torsional legs at the center. The frequency response of the sensor showed two resonance frequencies at approximately 1.1 kHz (rocking) and 1.5 kHz (bending). The resonance at 1.1 kHz is due to rocking of the wings by twisting the legs and the other at 1.5 kHz is due to bending of the bridge. The response of the sensor was probed electronically using comb finger capacitors integrated to the edges of the wings and with the help of an MS3110 chip. A peak output voltage of about 9V/Pa was measured for sound incident normal to the device at the resonance frequency of the bending mode. The bearing of the incident sound under these conditions could be determined to within a few degrees. These findings indicate the potential use of the MEMS sensor to locate sound sources with high accuracy. © (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- 3 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 100361A-100361A-7
MEMS directional acoustic sensor for locating sound sources
- 3 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 100361A-100361A-7
MEMS directional acoustic sensor for locating sound sources
- Open Access
- 1 January 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (1) , 015209
Understanding of self-terminating pulse generation using silicon controlled rectifier and RC load
Recently a silicon controlled rectifier (SCR)-based circuit that generates self-terminating voltage pulses was employed for the detection of light and ionizing radiation in pulse mode. The circuit consisted of a SCR connected in series with a RC load and DC bias. In this paper, we report the investigation of the physics underlying the pulsing mechanism of the SCR-based. It was found that during the switching of SCR, the voltage across the capacitor increased beyond that of the DC bias, thus generating a reverse current in the circuit, which helped to turn the SCR off. The pulsing was found to be sustainable only for a specific range of RC values depending on the SCR’s intrinsic turn-on/off times. The findings of this work will help to design optimum SCR based circuits for pulse mode detection of light and ionizing radiation without external amplification circuitry.
- 1 January 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (1) , 015209
Open AccessUnderstanding of self-terminating pulse generation using silicon controlled rectifier and RC load
Recently a silicon controlled rectifier (SCR)-based circuit that generates self-terminating voltage pulses was employed for the detection of light and ionizing radiation in pulse mode. The circuit consisted of a SCR connected in series with a RC load and DC bias. In this paper, we report the investigation of the physics underlying the pulsing mechanism of the SCR-based. It was found that during the switching of SCR, the voltage across the capacitor increased beyond that of the DC bias, thus generating a reverse current in the circuit, which helped to turn the SCR off. The pulsing was found to be sustainable only for a specific range of RC values depending on the SCR’s intrinsic turn-on/off times. The findings of this work will help to design optimum SCR based circuits for pulse mode detection of light and ionizing radiation without external amplification circuitry.
- 1 September 2015
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 138 (3_Suppleme) , 1768
High sensitive MEMS directional sound sensor with comb finger capacitor electronic readout
The conventional directional sound sensing systems employ an array of spatially separated microphones to achieve directional sensing by monitoring the arrival times and amplitudes of different microphones. However, there are insects such as Ormia ochracea fly that can determine the direction of sound using its miniature-hearing organ much smaller than the wavelength of sound it detects. The fly’s eardrums that are coupled mechanically with separation merely by about 1 mm have remarkable sensitivity to the direction of sound. Our MEMS based sensor, which consists of two 1 mm2 wings connected in the middle, similar to the fly’s hearing system, was designed and fabricated using silicon on insulator (SOI) substrate. The vibration of the wings in response to incident sound at the bending resonance was measured using a laser vibrometer found to be about 1 μm/Pa. For measuring sensor response electronically, comb finger capacitors were integrated on to the wins and the measured output using a MS3110 capacitive to voltage converter was found to be about 25 V/Pa. The fabricated sensors showed cos2q directional response similar to a pressure gradient microphone. The directional response of the sensor was measured down to about 30 dB.
- 1 September 2015
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 138 (3_Suppleme) , 1768
High sensitive MEMS directional sound sensor with comb finger capacitor electronic readout
The conventional directional sound sensing systems employ an array of spatially separated microphones to achieve directional sensing by monitoring the arrival times and amplitudes of different microphones. However, there are insects such as Ormia ochracea fly that can determine the direction of sound using its miniature-hearing organ much smaller than the wavelength of sound it detects. The fly’s eardrums that are coupled mechanically with separation merely by about 1 mm have remarkable sensitivity to the direction of sound. Our MEMS based sensor, which consists of two 1 mm2 wings connected in the middle, similar to the fly’s hearing system, was designed and fabricated using silicon on insulator (SOI) substrate. The vibration of the wings in response to incident sound at the bending resonance was measured using a laser vibrometer found to be about 1 μm/Pa. For measuring sensor response electronically, comb finger capacitors were integrated on to the wins and the measured output using a MS3110 capacitive to voltage converter was found to be about 25 V/Pa. The fabricated sensors showed cos2q directional response similar to a pressure gradient microphone. The directional response of the sensor was measured down to about 30 dB.