Moon-Seok Nam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Moon-Seok Nam has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chi-Oug Noh
Graduate Student Deparment of Civil Engineering Pukyong National University 48513 Busan Korea
1 shared publication - Cumaraswamy Vipulanandan
Department of Civil and Environmental Engineering, Center for Innovative Grouting Materials and Technology (CIGMAT), University of Houston, Houston, USA
1 shared publication - Hwan-Woo Lee
Deparment of Civil Engineering Pukyong National University 48513 Busan Korea
1 shared publication - Mincheol Park
Kumoh National Institute of Technology, Gumi-si 39177, Korea
1 shared publication - Seung-Won Kim
Graduate Student Deparment of Civil Engineering Pukyong National University 48513 Busan Korea
1 shared publication - Yongkyu Choi
Professor, Dept. of Civil Engineering, Kyungsung Univ., Busan 608-736, Korea
1 shared publication
Latest Publications
- Open Access
- 1 August 2021
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 34 (4) , 255-262
Numerical Analysis Models for Jointless Bridges Through Sensitivity Analysis
- 1 August 2021
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 34 (4) , 255-262
Open AccessNumerical Analysis Models for Jointless Bridges Through Sensitivity Analysis
- Open Access
- 15 March 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (3) , 833
Numerical Analysis of the Behavior of an IPM Bridge According to Super-Structure and Sub-Structure Properties
A bridge with an integrated and pile-bent abutment with a mechanically stabilized earth-wall (IPM) was developed by separating earth pressure from the abutment to overcome the problems typically faced by integral abutment bridges. Also, the IPM bridge removes expansion joints and bearing by integrating the super-structure and the abutment and does not need many piles because it separates the earth pressure from backfills. Therefore, it is superior in cost, durability, and maintainability to traditional bridges and is sustainable due to using less material. A numerical analysis was conducted to ascertain the behavior of the IPM bridge according to its super-structural and sub-structural characteristics. Based on the analysis results, the behaviors of the IPM bridge are as follows: The bending moments of the pre-stressed concrete (PSC) girder and the steel-plate girder of the bridge were influenced by the presence of the time-dependent loads. The contraction behavior in the PSC girder is largely due to the time-dependent loads, whereas the expansion behavior in the steel-plate girder is large due to its greater thermal expansion coefficient and temperature range compared with those of the PSC girder. In general, the suggested bridge length limit for PSC girders in both the integral abutment bridge and the IPM bridge is larger than that in a steel bridge. This needs to be reviewed again with consideration of the long-term and seasonal behaviors.- 15 March 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (3) , 833
Open AccessNumerical Analysis of the Behavior of an IPM Bridge According to Super-Structure and Sub-Structure Properties
A bridge with an integrated and pile-bent abutment with a mechanically stabilized earth-wall (IPM) was developed by separating earth pressure from the abutment to overcome the problems typically faced by integral abutment bridges. Also, the IPM bridge removes expansion joints and bearing by integrating the super-structure and the abutment and does not need many piles because it separates the earth pressure from backfills. Therefore, it is superior in cost, durability, and maintainability to traditional bridges and is sustainable due to using less material. A numerical analysis was conducted to ascertain the behavior of the IPM bridge according to its super-structural and sub-structural characteristics. Based on the analysis results, the behaviors of the IPM bridge are as follows: The bending moments of the pre-stressed concrete (PSC) girder and the steel-plate girder of the bridge were influenced by the presence of the time-dependent loads. The contraction behavior in the PSC girder is largely due to the time-dependent loads, whereas the expansion behavior in the steel-plate girder is large due to its greater thermal expansion coefficient and temperature range compared with those of the PSC girder. In general, the suggested bridge length limit for PSC girders in both the integral abutment bridge and the IPM bridge is larger than that in a steel bridge. This needs to be reviewed again with consideration of the long-term and seasonal behaviors. - 1 September 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (9) , 1272-1279
Roughness and Unit Side Resistances of Drilled Shafts Socketed in Clay Shale and Limestone
Rock socketed drilled shafts are being used increasingly to support heavily loaded structures. Rock sockets provide resistance to the load through a combination of side and base resistances. In this study, the effect of drilling tools such as an auger and a core barrel on the unit side resistance was investigated. A total of four field studies were performed on clay shale (compressive strength of 1–2 MPa ) and limestone (compressive strength of 10 MPa ). Borehole roughnesses produced by the different types of drilling tools in clay shale and limestone were measured using a laser borehole roughness profiler developed in this study to measure roughness to 0.5 mm in the boreholes. Based on the results of this study, it was observed that the drilling tools developed different socket roughnesses, which in turn affected the side resistances of the rock socketed drilled shafts.
- 1 September 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (9) , 1272-1279
Roughness and Unit Side Resistances of Drilled Shafts Socketed in Clay Shale and Limestone
Rock socketed drilled shafts are being used increasingly to support heavily loaded structures. Rock sockets provide resistance to the load through a combination of side and base resistances. In this study, the effect of drilling tools such as an auger and a core barrel on the unit side resistance was investigated. A total of four field studies were performed on clay shale (compressive strength of 1–2 MPa ) and limestone (compressive strength of 10 MPa ). Borehole roughnesses produced by the different types of drilling tools in clay shale and limestone were measured using a laser borehole roughness profiler developed in this study to measure roughness to 0.5 mm in the boreholes. Based on the results of this study, it was observed that the drilling tools developed different socket roughnesses, which in turn affected the side resistances of the rock socketed drilled shafts.
- Open Access
- 1 September 2007
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 11 (5) , 243-252
Structural resistance factors for shear loading in drilled shafts with minor flaws based on experimental study
- 1 September 2007
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 11 (5) , 243-252
Open AccessStructural resistance factors for shear loading in drilled shafts with minor flaws based on experimental study