Alakesh Manna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Alakesh Manna has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Amandeep Kundal
Department of Mechanical Engineering, Punjab Engineering College (DU), Chandigarh, India
2 shared publicationsAnup Malik
Lovely Professional University
2 shared publicationsH.S. Bains
Department of Mechanical Engineering, Sant Longowal Institute of Engineering & Technology, Sangrur, India
2 shared publications- Harlal Singh Mali
Malaviya National Institute of Technology Jaipur
2 shared publications P.B. Mahapatra
Department of Mechanical Engineering, Punjab Engineering College University of Technology, Chandigarh 160012, India
2 shared publications- Ajai Jain
National Institute of Technology
1 shared publication
Latest Publications
- 16 August 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 10 (2) , 187-197
Experimental investigation of wire EDM parameters during machining of fabricated hybrid Al/(SiC+ZrO 2 +NiTi)-MMC
Nowadays, advanced engineering materials are gradually becoming more attractive to the industries because of their high fatigue strength, hardness, thermal shock resistance, attractive strength to weight ratio, etc. Aluminium metal matrix composites (MMCs) have such properties and good electrical conductivity. Therefore, wire electrical discharge machining (WEDM) was found to be a suitable process for machining of such materials. The open gap voltage, pulse-on-time, pulse-off-time, peak current, wire feed rate and wire tension were considered as input process parameters, and experiments were carried out on fabricated hybrid Al/(SiC+ZrO2+ NiTi)-MMC. Taguchi method-based L18 (21x37) mixed orthogonal array was employed for planning of experiments. The process parameters were optimised for material removal rate (MRR) and surface roughness (SR) heights. Confirmation results reveals 61.88%, −28.75% and −20.25% improvement in MRR, Ra and Rt respectively, over initial setting. From analysis of variance (ANOVA), open gap voltage and pulse-on-time were found significant parameters for MRR and SR. The mathematical models for MRR and SR were developed and confirmation test reveals good agreement of it with experimental results. Scanning electron microscopy images reveal that the recast layer thickness was 8.569 µm at optimal MRR setting and 6.113 µm at optimal surface roughness (Ra) setting.
- 16 August 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 10 (2) , 187-197
Experimental investigation of wire EDM parameters during machining of fabricated hybrid Al/(SiC+ZrO 2 +NiTi)-MMC
Nowadays, advanced engineering materials are gradually becoming more attractive to the industries because of their high fatigue strength, hardness, thermal shock resistance, attractive strength to weight ratio, etc. Aluminium metal matrix composites (MMCs) have such properties and good electrical conductivity. Therefore, wire electrical discharge machining (WEDM) was found to be a suitable process for machining of such materials. The open gap voltage, pulse-on-time, pulse-off-time, peak current, wire feed rate and wire tension were considered as input process parameters, and experiments were carried out on fabricated hybrid Al/(SiC+ZrO2+ NiTi)-MMC. Taguchi method-based L18 (21x37) mixed orthogonal array was employed for planning of experiments. The process parameters were optimised for material removal rate (MRR) and surface roughness (SR) heights. Confirmation results reveals 61.88%, −28.75% and −20.25% improvement in MRR, Ra and Rt respectively, over initial setting. From analysis of variance (ANOVA), open gap voltage and pulse-on-time were found significant parameters for MRR and SR. The mathematical models for MRR and SR were developed and confirmation test reveals good agreement of it with experimental results. Scanning electron microscopy images reveal that the recast layer thickness was 8.569 µm at optimal MRR setting and 6.113 µm at optimal surface roughness (Ra) setting.
- Open Access
- 1 January 2022
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 61 (1) , 931-953
Multi-objective parametric optimization on the EDM machining of hybrid SiCp/Grp/aluminum nanocomposites using Non-dominating Sorting Genetic Algorithm (NSGA-II): Fabrication and microstructural characterizations
In this study, different input parameters for electric discharge machining (EDM) are examined in order to revise the distinctiveness of EDM for machining aluminum-based hybrid metal matrix composites (MMCs). The versatility of hybrid aluminum MMCs makes them very popular and sought after in the automotive, aerospace, marine, and space industries. In this article, an optimized process parameter setting for hybrid MCCs machining with an EDM machine is determined that have silicon carbide (SiCp) and graphite (Grp) particles added as reinforcement materials in varying amounts (Al–0.7Fe–0.6Si–0.375Cr–0.25Zn/10 wt%SiC/3 wt%Gr–MMC, Al–0.7Fe–0.6Si–0.375Cr–0.25Zn/15 wt%SiC/5 wt%Gr–MMC, and Al–0.7Fe–0.6Si–0.373Cr–0.25Zn/20 wt%SiC/8 wt%Gr–MMC). The stir casting method was used to prepare these hybrid aluminum MMCs (3 samples). A study of surface roughness (SR) and material removal rate (MRR) was conducted to examine the effects of dominant parameters. An experiment is planned using a central composite rotatable design (CCRD) of response surface methodology (RSM). It is possible to predict MRR and SR with 95% degree of accuracy by utilizing the quadratic model. Non-dominating Sorting Genetic Algorithm-II was employed to solve “mathematical models” for multi-objective optimization of output response characteristics. The scanning electron microscope (SEM) images of the tool and workpiece materials show that the recast layer has been formed on the tool face and the surface of the machined work-piece. Based on the results, it was determined that an optimal value of MRR (2.97 g·min−1) was obtained at 90 µs, 30 µs, 7.0 V, and 14 A asPon,Poff, gap voltage, and peak current, respectively. As a result of the findings, the SR is reciprocally proportional toPon, and the SR is commensurate withPoff. It was determined that the optimal value of SR (2.41 µm) could be attained at 30 µs, 52 µs, 6.0 V, and 12 A as thePon,Poff, gap voltage, and peak current, respectively. For an optimal set of response variables,Poncan be specified as 30 µs,Poffas 30 µs, gap voltage as 6 V, and peak current as 14 A as process parameters for MRR and SR. The SEM images of the tool material and the workpiece material clearly demonstrate a recast layer formed on the tool face and the machined surface of the workpiece. The optical microscopy analysis reveals a uniform distribution of SiCpand Grpparticles in the Al–0.7Fe–0.6Si–0.375Cr–0.25Zn matrix. In addition to recast layers and machined surfaces, EDS analysis reveals the deposition of tool material on the surface of the workpiece. The composites fabricated may replace materials in many of these applications where “friction” is a significant factor.
- 1 January 2022
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 61 (1) , 931-953
Open AccessMulti-objective parametric optimization on the EDM machining of hybrid SiCp/Grp/aluminum nanocomposites using Non-dominating Sorting Genetic Algorithm (NSGA-II): Fabrication and microstructural characterizations
In this study, different input parameters for electric discharge machining (EDM) are examined in order to revise the distinctiveness of EDM for machining aluminum-based hybrid metal matrix composites (MMCs). The versatility of hybrid aluminum MMCs makes them very popular and sought after in the automotive, aerospace, marine, and space industries. In this article, an optimized process parameter setting for hybrid MCCs machining with an EDM machine is determined that have silicon carbide (SiCp) and graphite (Grp) particles added as reinforcement materials in varying amounts (Al–0.7Fe–0.6Si–0.375Cr–0.25Zn/10 wt%SiC/3 wt%Gr–MMC, Al–0.7Fe–0.6Si–0.375Cr–0.25Zn/15 wt%SiC/5 wt%Gr–MMC, and Al–0.7Fe–0.6Si–0.373Cr–0.25Zn/20 wt%SiC/8 wt%Gr–MMC). The stir casting method was used to prepare these hybrid aluminum MMCs (3 samples). A study of surface roughness (SR) and material removal rate (MRR) was conducted to examine the effects of dominant parameters. An experiment is planned using a central composite rotatable design (CCRD) of response surface methodology (RSM). It is possible to predict MRR and SR with 95% degree of accuracy by utilizing the quadratic model. Non-dominating Sorting Genetic Algorithm-II was employed to solve “mathematical models” for multi-objective optimization of output response characteristics. The scanning electron microscope (SEM) images of the tool and workpiece materials show that the recast layer has been formed on the tool face and the surface of the machined work-piece. Based on the results, it was determined that an optimal value of MRR (2.97 g·min−1) was obtained at 90 µs, 30 µs, 7.0 V, and 14 A asPon,Poff, gap voltage, and peak current, respectively. As a result of the findings, the SR is reciprocally proportional toPon, and the SR is commensurate withPoff. It was determined that the optimal value of SR (2.41 µm) could be attained at 30 µs, 52 µs, 6.0 V, and 12 A as thePon,Poff, gap voltage, and peak current, respectively. For an optimal set of response variables,Poncan be specified as 30 µs,Poffas 30 µs, gap voltage as 6 V, and peak current as 14 A as process parameters for MRR and SR. The SEM images of the tool material and the workpiece material clearly demonstrate a recast layer formed on the tool face and the machined surface of the workpiece. The optical microscopy analysis reveals a uniform distribution of SiCpand Grpparticles in the Al–0.7Fe–0.6Si–0.375Cr–0.25Zn matrix. In addition to recast layers and machined surfaces, EDS analysis reveals the deposition of tool material on the surface of the workpiece. The composites fabricated may replace materials in many of these applications where “friction” is a significant factor.
- 14 October 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (7) , 8361-8372
Fabrication and Processing of Bioabsorbable Hybrid Zn/(Ag + Fe + Mg)-MMC on Developed Ultrasonic Vibration-Assisted Argon Atmosphere Stir Casting Set-up
- 14 October 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (7) , 8361-8372
Fabrication and Processing of Bioabsorbable Hybrid Zn/(Ag + Fe + Mg)-MMC on Developed Ultrasonic Vibration-Assisted Argon Atmosphere Stir Casting Set-up
- Open Access
- 7 July 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (7) , 8031-8043
Multi-Objective Optimization of WEDM of Aluminum Hybrid Composites Using AHP and Genetic Algorithm
Aluminum hybrid composites have the potential to satisfy emerging demands of lightweight materials with enhanced mechanical properties and lower manufacturing costs. There is an inclusion of reinforcing materials with variable concentrations for the preparation of hybrid metal matrix composites to attain customized properties. Hence, it is obligatory to investigate the impact of different machining conditions for the selection of optimum parameter settings for aluminum-based hybrid metal matrix composite material. The present study aims to identify the optimum machining parameters during wire electrical discharge machining of samples prepared with graphite, ferrous oxide, and silicon carbide. In the present research work, five different process parameters and three response parameters such as material removal rate, surface roughness, and spark Gap are considered for process optimization. Energy-dispersive spectroscopy and scanning electron microscopy analysis reported the manifestation of the recast layer. Analytical hierarchy process and genetic algorithm have been successfully implemented to identify the best machining conditions for hybrid composites.
- 7 July 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (7) , 8031-8043
Open AccessMulti-Objective Optimization of WEDM of Aluminum Hybrid Composites Using AHP and Genetic Algorithm
Aluminum hybrid composites have the potential to satisfy emerging demands of lightweight materials with enhanced mechanical properties and lower manufacturing costs. There is an inclusion of reinforcing materials with variable concentrations for the preparation of hybrid metal matrix composites to attain customized properties. Hence, it is obligatory to investigate the impact of different machining conditions for the selection of optimum parameter settings for aluminum-based hybrid metal matrix composite material. The present study aims to identify the optimum machining parameters during wire electrical discharge machining of samples prepared with graphite, ferrous oxide, and silicon carbide. In the present research work, five different process parameters and three response parameters such as material removal rate, surface roughness, and spark Gap are considered for process optimization. Energy-dispersive spectroscopy and scanning electron microscopy analysis reported the manifestation of the recast layer. Analytical hierarchy process and genetic algorithm have been successfully implemented to identify the best machining conditions for hybrid composites.
- 5 January 2021
- Published by Springer Nature in Silicon
- Vol. 14 (3) , 869-882
Performance Evaluation of Al-SiC Nanofluids Based MQL Sustainable Cooling Techniques During Turning of EN-24 Steel
- 5 January 2021
- Published by Springer Nature in Silicon
- Vol. 14 (3) , 869-882
Performance Evaluation of Al-SiC Nanofluids Based MQL Sustainable Cooling Techniques During Turning of EN-24 Steel
- 11 May 2020
- Published by Springer Nature
- p. 255-268
Finishing of Curved Surface by Rotary Abrasive Float Polishing
- 11 May 2020
- Published by Springer Nature
- p. 255-268
Finishing of Curved Surface by Rotary Abrasive Float Polishing
- 4 December 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 43 (9) , 4593-4608
Study on Precision Microholes Using Pulsed Laser with Jet Electrochemical Machining
- 4 December 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 43 (9) , 4593-4608
Study on Precision Microholes Using Pulsed Laser with Jet Electrochemical Machining
- 1 April 2017
- Published by Elsevier in Diamond and Related Materials
- Vol. 74, 100-107
Direct growth of coiled carbon nanofibers without nanocatalyst
- 1 April 2017
- Published by Elsevier in Diamond and Related Materials
- Vol. 74, 100-107
Direct growth of coiled carbon nanofibers without nanocatalyst
- 12 September 2015
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 38 (2) , 481-491
Experimental investigation of spark gap and material removal rate of Al/ZrO2(P)-MMC machined with wire EDM
- 12 September 2015
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 38 (2) , 481-491
Experimental investigation of spark gap and material removal rate of Al/ZrO2(P)-MMC machined with wire EDM
- 29 April 2014
- Published by Springer Nature
- p. 261-271
An Experimental Investigation During Wire Electrical Discharge Machining of Al/SiC-MMC
- 29 April 2014
- Published by Springer Nature
- p. 261-271
An Experimental Investigation During Wire Electrical Discharge Machining of Al/SiC-MMC