Hasan Sofuoglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hasan Sofuoglu has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Alaettin Ozer
Department of Mechanical Engineering, Bozok University, Yozgat, Turkey
3 shared publications Faruk Güner
3 shared publications- Mehmet Emin Çetin
Necmettin Erbakan Universitesi
3 shared publications Ömer Necati Cora
Department of Mechanical Engineering, Karadeniz Technical University, Trabzon 61080, Turkey
3 shared publications- Ömer Necati Cora
KARADENİZ TEKNİK ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ
3 shared publications Aydın Bıyıklıoglu
2 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Elsevier in SSRN Electronic Journal
Effects of Additive Manufacturing Process on the Microstructural and Mechanical Properties of 316L Substrate Coated with Ti6Al4V Powder by Cold Spraying Method
In this study, the microstructural and mechanical properties of the 316L stainless steel substrate (316L-SSS) produced with additive manufacturing (AM) method and the coated substrate (Ti-CS-SSS) subsequently coated with Ti6Al4V powders using the cold spray (CS) method were comprehensively investigated. The microstructural features, phase evolution, and mechanical performance of the resulting bimetallic structure were examined using SEM, EDS, XRD, microhardness, and uniaxial tensile tests. The results demonstrated that while a porosity of approximately 20% and an accompanying low apparent hardness were detected in the coating layer due to the physical limitations of the process gas, the austenitic substrate structure, produced with extremely high cooling rates, maintained its superior hardness without undergoing any thermal degradation. Furthermore, tensile tests and fracture surface analyses revealed that the 316L-SSS exhibited anisotropic behavior depending on the build direction, and the geometric elongation mismatch between the ductile substrate and the severely strain-hardened brittle coating layer drove the failure mechanism toward interfacial debonding. In conclusion, it was proven that the topography provided by the as-built 316L-SSS effectively tolerates low kinetic energy in LPCS systems, maximizing coating adhesion and offering an innovative foundation for the synthesis of functional bimetallic structures.
- 15 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffects of Additive Manufacturing Process on the Microstructural and Mechanical Properties of 316L Substrate Coated with Ti6Al4V Powder by Cold Spraying Method
In this study, the microstructural and mechanical properties of the 316L stainless steel substrate (316L-SSS) produced with additive manufacturing (AM) method and the coated substrate (Ti-CS-SSS) subsequently coated with Ti6Al4V powders using the cold spray (CS) method were comprehensively investigated. The microstructural features, phase evolution, and mechanical performance of the resulting bimetallic structure were examined using SEM, EDS, XRD, microhardness, and uniaxial tensile tests. The results demonstrated that while a porosity of approximately 20% and an accompanying low apparent hardness were detected in the coating layer due to the physical limitations of the process gas, the austenitic substrate structure, produced with extremely high cooling rates, maintained its superior hardness without undergoing any thermal degradation. Furthermore, tensile tests and fracture surface analyses revealed that the 316L-SSS exhibited anisotropic behavior depending on the build direction, and the geometric elongation mismatch between the ductile substrate and the severely strain-hardened brittle coating layer drove the failure mechanism toward interfacial debonding. In conclusion, it was proven that the topography provided by the as-built 316L-SSS effectively tolerates low kinetic energy in LPCS systems, maximizing coating adhesion and offering an innovative foundation for the synthesis of functional bimetallic structures.
- 19 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (9-10) , 2935-2948
Coupled effect of thickness optimization and plastic forming history on crashworthiness performance of thin-walled square tube
- 19 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (9-10) , 2935-2948
Coupled effect of thickness optimization and plastic forming history on crashworthiness performance of thin-walled square tube
- Open Access
- 24 February 2021
- Published by Springer Nature in Research Square
Coupled Effect of Thickness Optimization and Plastic Forming History on Crashworthiness Performance of Thin-Walled Square Tube
Thin-walled tubes are widely used as energy absorbers due to their high crashworthiness performance. This study aims to evaluate the effect of plastic forming history carried out for thickness optimization on crashworthiness performance of thin-walled square tube (TWST). Within the scope of the study, a series of numerical analyses were conducted for the TWST using a commercial finite element (FE) software. In order to determine individual effect of optimization, FG thickness of TWST was first obtained using LS-OPT software. Later, thickness gradient was achieved by performing rolling process to consider individual plastic forming effect Afterwards, deep drawing process was carried out to shape TWST by considering springback and trimming effects. Finally, crash responses were obtained under axial high velocity impact loading to determine the coupled effect of optimization and plastic forming on the crashworthiness performance of the TWST. It was determined that the coupled effect, which takes plastic forming and optimization effects into account, reduced the peak crush force of the TWST by 24% and increased the absorbed energy value by 39%. The results obtained from this study showed that coupled effect of optimization and plastic forming processes has significant effect on the crashworthiness performance of the TWST and otherwise either overestimated or underestimated results are obtained.
- 24 February 2021
- Published by Springer Nature in Research Square
Open AccessCoupled Effect of Thickness Optimization and Plastic Forming History on Crashworthiness Performance of Thin-Walled Square Tube
Thin-walled tubes are widely used as energy absorbers due to their high crashworthiness performance. This study aims to evaluate the effect of plastic forming history carried out for thickness optimization on crashworthiness performance of thin-walled square tube (TWST). Within the scope of the study, a series of numerical analyses were conducted for the TWST using a commercial finite element (FE) software. In order to determine individual effect of optimization, FG thickness of TWST was first obtained using LS-OPT software. Later, thickness gradient was achieved by performing rolling process to consider individual plastic forming effect Afterwards, deep drawing process was carried out to shape TWST by considering springback and trimming effects. Finally, crash responses were obtained under axial high velocity impact loading to determine the coupled effect of optimization and plastic forming on the crashworthiness performance of the TWST. It was determined that the coupled effect, which takes plastic forming and optimization effects into account, reduced the peak crush force of the TWST by 24% and increased the absorbed energy value by 39%. The results obtained from this study showed that coupled effect of optimization and plastic forming processes has significant effect on the crashworthiness performance of the TWST and otherwise either overestimated or underestimated results are obtained.
- 5 September 2019
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 142 (1)
Micro Deep Drawability of the Superplastic Zn–22Al Alloy at a High Strain Rate and Room Temperature
This study aimed to investigate the micro deep drawability of the Zn–22Al alloy at room temperature in which it shows superplastic properties. To this goal, first the two-step equal channel angular extrusion (ECAE) process was carried out to obtain an ultra-fine-grained structure (UFG). Upon achieving the grain size of 200 nm, the formability of the alloy at room temperature and at a high strain rate was investigated both experimentally and numerically. Micro deep drawing experiments were performed at different deep drawing ratios (1.66, 1.84, 2.0, and 2.25) and for different sheet thicknesses (0.2, 0.4, and 0.6 mm). The finite element model of the micro deep drawing was also established to assess and compare the thickness variation in deep drawn parts. Results showed that the superplastic Zn–22Al alloy has a great potential in microforming applications. It was also noted that the limiting drawing ratio can be obtained as high as 2.25 in the room temperature condition.
- 5 September 2019
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 142 (1)
Micro Deep Drawability of the Superplastic Zn–22Al Alloy at a High Strain Rate and Room Temperature
This study aimed to investigate the micro deep drawability of the Zn–22Al alloy at room temperature in which it shows superplastic properties. To this goal, first the two-step equal channel angular extrusion (ECAE) process was carried out to obtain an ultra-fine-grained structure (UFG). Upon achieving the grain size of 200 nm, the formability of the alloy at room temperature and at a high strain rate was investigated both experimentally and numerically. Micro deep drawing experiments were performed at different deep drawing ratios (1.66, 1.84, 2.0, and 2.25) and for different sheet thicknesses (0.2, 0.4, and 0.6 mm). The finite element model of the micro deep drawing was also established to assess and compare the thickness variation in deep drawn parts. Results showed that the superplastic Zn–22Al alloy has a great potential in microforming applications. It was also noted that the limiting drawing ratio can be obtained as high as 2.25 in the room temperature condition.
- 1 June 2018
- Published by Elsevier in Tribology International
- Vol. 122, 125-132
Effects of friction models on the compaction behavior of copper powder
- 1 June 2018
- Published by Elsevier in Tribology International
- Vol. 122, 125-132
Effects of friction models on the compaction behavior of copper powder
- 19 February 2018
- Published by Springer Nature in Australasian Physics & Engineering Sciences in Medicine
- Vol. 41 (1) , 177-188
A statistical approach to explore cemented total hip reconstruction performance
This study was carried out to determine mechanical behavior and bone adaptation of total hip arthroplasty (THA) subject to concentrated and distributed muscle loads and hip contact forces during activities of walking and stair climbing. Finite element modeling of THA with different prostheses, activity and loading types was developed by adopting a statistical method. Two levels of prostheses, activity, and loading types were selected for the study. 23 factorial method was then pursued to design input and output data of finite element analysis. Maximum von Mises stresses were chosen to be output data on which statistical investigation was performed to investigate contribution and interaction of main factors on mechanical failure of cemented THA reconstructions by utilizing analysis of variance method (ANOVA). This study illustrated that the maximum von Mises stresses of THA showed considerable variation for main factors and their two-factor interactions.
- 19 February 2018
- Published by Springer Nature in Australasian Physics & Engineering Sciences in Medicine
- Vol. 41 (1) , 177-188
A statistical approach to explore cemented total hip reconstruction performance
This study was carried out to determine mechanical behavior and bone adaptation of total hip arthroplasty (THA) subject to concentrated and distributed muscle loads and hip contact forces during activities of walking and stair climbing. Finite element modeling of THA with different prostheses, activity and loading types was developed by adopting a statistical method. Two levels of prostheses, activity, and loading types were selected for the study. 23 factorial method was then pursued to design input and output data of finite element analysis. Maximum von Mises stresses were chosen to be output data on which statistical investigation was performed to investigate contribution and interaction of main factors on mechanical failure of cemented THA reconstructions by utilizing analysis of variance method (ANOVA). This study illustrated that the maximum von Mises stresses of THA showed considerable variation for main factors and their two-factor interactions.
- Open Access
- 1 January 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 295 (1) , 012027
Effects of Process Parameters on Copper Powder Compaction Process Using Multi-Particle Finite Element Method
Powder metallurgy (PM) has been widely used in several industries; especially automotive and aerospace industries and powder metallurgy products grow up every year. The mechanical properties of the final product that is obtained by cold compaction and sintering in powder metallurgy are closely related to the final relative density of the process. The distribution of the relative density in the die is affected by parameters such as compaction velocity, friction coefficient and temperature. Moreover, most of the numerical studies utilizing finite element approaches treat the examined environment as a continuous media with uniformly homogeneous porosity whereas Multi-Particle Finite Element Method (MPFEM) treats every particles as an individual body. In MPFEM, each of the particles can be defined as an elastic- plastic deformable body, so the interactions of the particles with each other and the die wall can be investigated. In this study, each particle was modelled and analyzed as individual deformable body with 3D tetrahedral elements by using MPFEM approach. This study, therefore, was performed to investigate the effects of different temperatures and compaction velocities on stress distribution and deformations of copper powders of 200 µm-diameter in compaction process. Furthermore, 3-D MPFEM model utilized von Mises material model and constant coefficient of friction of μ=0.05. In addition to MPFEM approach, continuum modelling approach was also performed for comparison purposes.
- 1 January 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 295 (1) , 012027
Open AccessEffects of Process Parameters on Copper Powder Compaction Process Using Multi-Particle Finite Element Method
Powder metallurgy (PM) has been widely used in several industries; especially automotive and aerospace industries and powder metallurgy products grow up every year. The mechanical properties of the final product that is obtained by cold compaction and sintering in powder metallurgy are closely related to the final relative density of the process. The distribution of the relative density in the die is affected by parameters such as compaction velocity, friction coefficient and temperature. Moreover, most of the numerical studies utilizing finite element approaches treat the examined environment as a continuous media with uniformly homogeneous porosity whereas Multi-Particle Finite Element Method (MPFEM) treats every particles as an individual body. In MPFEM, each of the particles can be defined as an elastic- plastic deformable body, so the interactions of the particles with each other and the die wall can be investigated. In this study, each particle was modelled and analyzed as individual deformable body with 3D tetrahedral elements by using MPFEM approach. This study, therefore, was performed to investigate the effects of different temperatures and compaction velocities on stress distribution and deformations of copper powders of 200 µm-diameter in compaction process. Furthermore, 3-D MPFEM model utilized von Mises material model and constant coefficient of friction of μ=0.05. In addition to MPFEM approach, continuum modelling approach was also performed for comparison purposes.
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 127-131
Numerical investigation of coefficient of friction in copper powder compaction process at micro scale
Multi Particle Finite Element Method (MPFEM) which is a power full approach for particle systems analyzes particle interactions via different friction models. In this study, Amontons-Coulomb constant friction (ACM), Wanheim/Bay generalized friction (WBM) and Levanov's friction models (LFM) are utilized in MPFEM in order to obtain coefficient of friction at particle-particle and particle-die wall interactions in spherical copper powder compaction. Friction models are introduced into the analysis by user subroutines. Compaction processes at room temperature and at 270°C were investigated by terms of coefficient of friction, shear stress and equivalent strain. Although equivalent strain curve of WBM and LFM are in good agreement, ACM resulted in higher equivalent strain and shear stress values. Coefficient of friction those were obtained with WBM and LFM varies in a reasonable range.
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 127-131
Numerical investigation of coefficient of friction in copper powder compaction process at micro scale
Multi Particle Finite Element Method (MPFEM) which is a power full approach for particle systems analyzes particle interactions via different friction models. In this study, Amontons-Coulomb constant friction (ACM), Wanheim/Bay generalized friction (WBM) and Levanov's friction models (LFM) are utilized in MPFEM in order to obtain coefficient of friction at particle-particle and particle-die wall interactions in spherical copper powder compaction. Friction models are introduced into the analysis by user subroutines. Compaction processes at room temperature and at 270°C were investigated by terms of coefficient of friction, shear stress and equivalent strain. Although equivalent strain curve of WBM and LFM are in good agreement, ACM resulted in higher equivalent strain and shear stress values. Coefficient of friction those were obtained with WBM and LFM varies in a reasonable range.
- 1 August 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 672, 78-87
Effects of grain size on room temperature deformation behavior of Zn–22Al alloy under uniaxial and biaxial loading conditions
- 1 August 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 672, 78-87
Effects of grain size on room temperature deformation behavior of Zn–22Al alloy under uniaxial and biaxial loading conditions
- 1 April 2016
- Published by Elsevier in Tribology International
- Vol. 96, 1-10
An investigation of contact interactions in powder compaction process through variable friction models
- 1 April 2016
- Published by Elsevier in Tribology International
- Vol. 96, 1-10
An investigation of contact interactions in powder compaction process through variable friction models