Patrick Waltereit
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Patrick Waltereit has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Wolfgang Bronner
Fraunhofer-Institut für Angewandte Festkörperphysik (Germany)
8 shared publications M. Mikulla
Fraunhofer Institute for Applied Solid-State Physics, Tullastr. 72, D-79108 Freiburg, Germany
6 shared publications- Rüdiger Quay
Fraunhofer Institute for Applied Solid State Physics IAF, Freiburg, Germany
5 shared publications K. Riepe
United Monolithic Semiconductors, Wilhelm‐Runge‐Str. 11, 89081 Ulm, Germany
4 shared publicationsMichael Mikulla
Fraunhofer Institute for Applied Solid State Physics, Tullastr. 72, 79108 Freiburg, Germany
4 shared publicationsO. Ambacher
Fraunhofer Institute for Applied Solid-State Physics, Tullastr. 72, D-79108 Freiburg, Germany
4 shared publications
Latest Publications
- Open Access
Three-Phase Motor Inverter and Current Sensing GaN Power IC
A three-phase GaN-based motor inverter IC with three integrated phase current mirror sensors (sense-FETs or sense-HEMTs, 1200:1 ratio), a temperature sensor, and an amplifier is presented and experimentally operated. The three low-side currents are read out by virtual grounding transimpedance amplifiers. A modified summed DC current readout circuit using only one amplifier is also discussed. During continuous 24 V motor operation with space-vector pulse width modulation (SVPWM), the sensor signal is measured and a bidirectional measurement capability is verified. The measured risetime of the sensor signal is 51 ns, indicating around 7 MHz bandwidth (without intentional optimization for high bandwidth). The IC is operated up to 32 V on DC-biased semi-floating substrate to limit negative static back-gating of the high-side transistors to around −7% of the DC-link voltage. Analysis of the capacitive coupling from the three switch-nodes to the substrate is calculated for SVPWM based on capacitance measurement, resulting in four discrete semi-floating substrate voltage levels, which is experimentally verified. Integrated advanced power converter topologies with sensors improve the power density of power electronics applications, such as for low-voltage motor drive.
Open AccessThree-Phase Motor Inverter and Current Sensing GaN Power IC
A three-phase GaN-based motor inverter IC with three integrated phase current mirror sensors (sense-FETs or sense-HEMTs, 1200:1 ratio), a temperature sensor, and an amplifier is presented and experimentally operated. The three low-side currents are read out by virtual grounding transimpedance amplifiers. A modified summed DC current readout circuit using only one amplifier is also discussed. During continuous 24 V motor operation with space-vector pulse width modulation (SVPWM), the sensor signal is measured and a bidirectional measurement capability is verified. The measured risetime of the sensor signal is 51 ns, indicating around 7 MHz bandwidth (without intentional optimization for high bandwidth). The IC is operated up to 32 V on DC-biased semi-floating substrate to limit negative static back-gating of the high-side transistors to around −7% of the DC-link voltage. Analysis of the capacitive coupling from the three switch-nodes to the substrate is calculated for SVPWM based on capacitance measurement, resulting in four discrete semi-floating substrate voltage levels, which is experimentally verified. Integrated advanced power converter topologies with sensors improve the power density of power electronics applications, such as for low-voltage motor drive.
- Open Access
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (1) , 83-86
PCB-Embedded GaN-on-Si Half-Bridge and Driver ICs With On-Package Gate and DC-Link Capacitors
A low-inductive half-bridge and gate driver package with on-package gate and dc-link capacitors is realized by PCB-embedding of two GaN-on-Si ICs. While monolithic half-bridge and driver integration reduces on-chip parasitics, it does not solve the interconnection challenge to external capacitors. The work solves this issue through advantageous combination of PCB-embedding and monolithic circuit integration. The work uses GaN-on-Si power circuits with integrated gate drivers, freewheeling diodes, temperature and current sensors. GaN ICs are fabricated with thick copper on both sides, which makes them applicable to commercial PCB-embedding technologies. Thermal aspects are discussed and electro-magnetic simulations used to compare the PCB-embedded package to a bond wire based package. A PCB-embedded dc-dc converter is operated up to 350 V and 450 W with up to 98.7% efficiency. 380 V hard-switching transitions show below 8% over- and undershoot despite over 120 V/ns slew-rates. Parallel plate-like placement of silicon flip-chip capacitors above the gate driver final stage transistors and separated only by a thin PCB-layer increased the gate-loop parasitic inductance by only 40 pH.
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (1) , 83-86
Open AccessPCB-Embedded GaN-on-Si Half-Bridge and Driver ICs With On-Package Gate and DC-Link Capacitors
A low-inductive half-bridge and gate driver package with on-package gate and dc-link capacitors is realized by PCB-embedding of two GaN-on-Si ICs. While monolithic half-bridge and driver integration reduces on-chip parasitics, it does not solve the interconnection challenge to external capacitors. The work solves this issue through advantageous combination of PCB-embedding and monolithic circuit integration. The work uses GaN-on-Si power circuits with integrated gate drivers, freewheeling diodes, temperature and current sensors. GaN ICs are fabricated with thick copper on both sides, which makes them applicable to commercial PCB-embedding technologies. Thermal aspects are discussed and electro-magnetic simulations used to compare the PCB-embedded package to a bond wire based package. A PCB-embedded dc-dc converter is operated up to 350 V and 450 W with up to 98.7% efficiency. 380 V hard-switching transitions show below 8% over- and undershoot despite over 120 V/ns slew-rates. Parallel plate-like placement of silicon flip-chip capacitors above the gate driver final stage transistors and separated only by a thin PCB-layer increased the gate-loop parasitic inductance by only 40 pH.
- 18 February 2013
- Published by Wiley in physica status solidi (c)
- Vol. 10 (5) , 831-834
GaN‐based high voltage transistors for efficient power switching
We present results from GaN‐based high voltage transistors used for power switching applications. The static and dynamic properties of transistors on SiC and Si substrates are determined. Overall, this technology is capable to deliver 1000 V breakdown and 95 A output current as well as a lower product of on‐resistance and gate charge than conventional Si‐based structures. Areas of further improvement in epitaxial growth and device processing are outlined in order to combine these high currents and high voltages in a single device.
- 18 February 2013
- Published by Wiley in physica status solidi (c)
- Vol. 10 (5) , 831-834
GaN‐based high voltage transistors for efficient power switching
We present results from GaN‐based high voltage transistors used for power switching applications. The static and dynamic properties of transistors on SiC and Si substrates are determined. Overall, this technology is capable to deliver 1000 V breakdown and 95 A output current as well as a lower product of on‐resistance and gate charge than conventional Si‐based structures. Areas of further improvement in epitaxial growth and device processing are outlined in order to combine these high currents and high voltages in a single device.
- 9 January 2012
- Published by Wiley in Physica Status Solidi (a)
- Vol. 209 (3) , 491-496
GaN‐based high‐frequency devices and circuits: A Fraunhofer perspective
We present the current status of our technology for GaN‐based HEMTs and MMICs as well as results ranging from the L‐band up to the W‐band. Epitaxial growth is carried out on 4H‐SiC(0001) substrates by both MOCVD and MBE. Processing is done using standard III–V equipment including both frontside and backside processing. For L‐band power bars we arrive at output powers, efficiencies and gains beyond 100 W, 60% and 17 dB, all measured under cw conditions at 50 V drain bias. The X‐band MMICs are characterized by a high efficiency above 40% for two‐stage amplifiers. Towards mm‐wave applications we have fabricated HEMTs with transit frequencies above 100 GHz and W‐band MMICs delivering 0.5 W/mm at 94 GHz with 7% PAE. First quaternary InAlGaN barriers show promising results for this new materials system. Reliability tests return a very good long‐term stability of our devices even at an elevated channel temperature of 200 °C with an extrapolated lifetime of 5 × 105. Initial space capability tests including total ion dose radiation insensitivity, radiation displacement damage, hydrogen poisoning and single event effect are successfully passed.
- 9 January 2012
- Published by Wiley in Physica Status Solidi (a)
- Vol. 209 (3) , 491-496
GaN‐based high‐frequency devices and circuits: A Fraunhofer perspective
We present the current status of our technology for GaN‐based HEMTs and MMICs as well as results ranging from the L‐band up to the W‐band. Epitaxial growth is carried out on 4H‐SiC(0001) substrates by both MOCVD and MBE. Processing is done using standard III–V equipment including both frontside and backside processing. For L‐band power bars we arrive at output powers, efficiencies and gains beyond 100 W, 60% and 17 dB, all measured under cw conditions at 50 V drain bias. The X‐band MMICs are characterized by a high efficiency above 40% for two‐stage amplifiers. Towards mm‐wave applications we have fabricated HEMTs with transit frequencies above 100 GHz and W‐band MMICs delivering 0.5 W/mm at 94 GHz with 7% PAE. First quaternary InAlGaN barriers show promising results for this new materials system. Reliability tests return a very good long‐term stability of our devices even at an elevated channel temperature of 200 °C with an extrapolated lifetime of 5 × 105. Initial space capability tests including total ion dose radiation insensitivity, radiation displacement damage, hydrogen poisoning and single event effect are successfully passed.
- 7 November 2011
- Published by Wiley in physica status solidi (c)
- Vol. 9 (2) , 365-368
Trade‐offs between performance and reliability in AlGaN/GaN transistors
We report on the trade‐off between performance and reliability for AlGaN/GaN transistors. It is shown that changes in epitaxial growth, transistor design and process may lead to an improvement in performance but are, at the same time, accompanied by a degradation of device reliability. As a result we show strategies in order to balance performance and reliability as both are linked. Based on these findings we have realized state‐of‐the‐art power bars for mobile communication systems and X‐band MMICs for radar applications.
- 7 November 2011
- Published by Wiley in physica status solidi (c)
- Vol. 9 (2) , 365-368
Trade‐offs between performance and reliability in AlGaN/GaN transistors
We report on the trade‐off between performance and reliability for AlGaN/GaN transistors. It is shown that changes in epitaxial growth, transistor design and process may lead to an improvement in performance but are, at the same time, accompanied by a degradation of device reliability. As a result we show strategies in order to balance performance and reliability as both are linked. Based on these findings we have realized state‐of‐the‐art power bars for mobile communication systems and X‐band MMICs for radar applications.
- 1 February 2011
- Published by Elsevier in Microelectronics Reliability
- Vol. 51 (2) , 224-228
Critical factors influencing the voltage robustness of AlGaN/GaN HEMTs
- 1 February 2011
- Published by Elsevier in Microelectronics Reliability
- Vol. 51 (2) , 224-228
Critical factors influencing the voltage robustness of AlGaN/GaN HEMTs
- 22 June 2010
- Published by Wiley in physica status solidi (c)
- Vol. 7 (10) , 2398-2403
Development of rugged 2 GHz power bars delivering more than 100 W and 60% power added efficiency
- 22 June 2010
- Published by Wiley in physica status solidi (c)
- Vol. 7 (10) , 2398-2403
Development of rugged 2 GHz power bars delivering more than 100 W and 60% power added efficiency
- 1 February 2010
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 2 (1) , 3-11
AlGaN/GaN epitaxy and technology
We present an overview on epitaxial growth, processing technology, device performance, and reliability of our GaN high electron mobility transistors (HEMTs) manufactured on 3- and 4-in. SiC substrates. Epitaxy and processing are optimized for both performance and reliability. We use three different gate lengths, namely 500 nm for 1–6 GHz applications, 250 nm for devices between 6 and 18 GHz, and 150 nm for higher frequencies. The developed HEMTs demonstrate excellent high-voltage stability, high power performance, and large DC to RF conversion efficiencies for all gate lengths. On large gate width devices for base station applications, an output power beyond 125 W is achieved with a power added efficiency around 60% and a linear gain around 16 dB. Reliability is tested both under DC and RF conditions with supply voltage of 50 and 30 V for 500 and 250 nm gates, respectively. DC tests on HEMT devices return a drain current change of just about 10% under IDQ conditions. Under RF stress the observed change in output power density is below 0.2 dB after more than 1000 h for both gate length technologies.
- 1 February 2010
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 2 (1) , 3-11
AlGaN/GaN epitaxy and technology
We present an overview on epitaxial growth, processing technology, device performance, and reliability of our GaN high electron mobility transistors (HEMTs) manufactured on 3- and 4-in. SiC substrates. Epitaxy and processing are optimized for both performance and reliability. We use three different gate lengths, namely 500 nm for 1–6 GHz applications, 250 nm for devices between 6 and 18 GHz, and 150 nm for higher frequencies. The developed HEMTs demonstrate excellent high-voltage stability, high power performance, and large DC to RF conversion efficiencies for all gate lengths. On large gate width devices for base station applications, an output power beyond 125 W is achieved with a power added efficiency around 60% and a linear gain around 16 dB. Reliability is tested both under DC and RF conditions with supply voltage of 50 and 30 V for 500 and 250 nm gates, respectively. DC tests on HEMT devices return a drain current change of just about 10% under IDQ conditions. Under RF stress the observed change in output power density is below 0.2 dB after more than 1000 h for both gate length technologies.
- 8 June 2009
- Published by Wiley in physica status solidi (c)
- Vol. 6 (6) , 1369-1372
Development of AlGaN/GaN HEMTs with efficiencies above 60% up to 100 V for next generation mobile communication 100 W power bars
- 8 June 2009
- Published by Wiley in physica status solidi (c)
- Vol. 6 (6) , 1369-1372
Development of AlGaN/GaN HEMTs with efficiencies above 60% up to 100 V for next generation mobile communication 100 W power bars
- 3 June 2009
- Published by Wiley in Physica Status Solidi (a)
- Vol. 206 (6) , 1215-1220
GaN HEMT and MMIC development at Fraunhofer IAF: performance and reliability
We present a systematic study of epitaxial growth, processing technology, device performance and reliability of our GaN HEMTs and MMICs manufactured on 3 inch SiC substrates. Epitaxy and processing are optimized for both performance and reliability. The deposition of the AlGaN/GaN HEMT epitaxial structures is designed for low background carrier concentration and a low trap density in order to simultaneously achieve a high buffer isolation and low DC to RF dispersion. Device fabrication is performed using standard processing techniques involving both electron‐beam and stepper lithography. Gate lengths of 250 nm and 500 nm are employed for 10 GHz and 2 GHz applications, respectively. The developed HEMTs demonstrate excellent high‐voltage stability, high power performance and large power added efficiencies. Devices exhibit two‐terminal gate–drain breakdown voltages in excess of 160 V (current criterion 1 mA/mm) across the entire 3 inch wafer with parasitic gate and drain currents well below 1 mA/mm when biased up to 80 V drain bias under pinch‐off conditions. Load‐Pull measurements at 2 GHz on 800 μm gate width devices return a well‐behaved relationship between bias‐voltage and output‐power as well as power‐added‐efficiencies beyond 60% up toUDS= 100 V. For a drain bias of 100 V an output‐power‐density around 22 W/mm with 26 dB linear gain is obtained. On large devices (32 mm gate width packaged in industry‐standard ceramic packages) an output power beyond 100 W is achieved with a PAE above 50% and a linear gain around 15 dB. Dual‐stage MMICs in microstrip transmission line technology yield a power added efficiency of 40% at 8.56 GHz for a power level of 11 W. A single‐stage MMIC yields a PAE of 46% with 7 W of output power atVDS= 28 V. Reliability is tested on HEMT devices having a gate periphery of 8 × 60 μm at an operating bias of 50 V under both DC and RF conditions. About 10% drain‐current change under DC‐stress (50 mA/mm) is observed after more than 1000 h of operation with an extrapolated drain‐current degradation below 20% after 200000 h (more than 20 years) of operation. Under RF stress (2 GHz, 1 dB compression) the observed change in output power density is below 0.2 dB after more than 1000 h.
- 3 June 2009
- Published by Wiley in Physica Status Solidi (a)
- Vol. 206 (6) , 1215-1220
GaN HEMT and MMIC development at Fraunhofer IAF: performance and reliability
We present a systematic study of epitaxial growth, processing technology, device performance and reliability of our GaN HEMTs and MMICs manufactured on 3 inch SiC substrates. Epitaxy and processing are optimized for both performance and reliability. The deposition of the AlGaN/GaN HEMT epitaxial structures is designed for low background carrier concentration and a low trap density in order to simultaneously achieve a high buffer isolation and low DC to RF dispersion. Device fabrication is performed using standard processing techniques involving both electron‐beam and stepper lithography. Gate lengths of 250 nm and 500 nm are employed for 10 GHz and 2 GHz applications, respectively. The developed HEMTs demonstrate excellent high‐voltage stability, high power performance and large power added efficiencies. Devices exhibit two‐terminal gate–drain breakdown voltages in excess of 160 V (current criterion 1 mA/mm) across the entire 3 inch wafer with parasitic gate and drain currents well below 1 mA/mm when biased up to 80 V drain bias under pinch‐off conditions. Load‐Pull measurements at 2 GHz on 800 μm gate width devices return a well‐behaved relationship between bias‐voltage and output‐power as well as power‐added‐efficiencies beyond 60% up toUDS= 100 V. For a drain bias of 100 V an output‐power‐density around 22 W/mm with 26 dB linear gain is obtained. On large devices (32 mm gate width packaged in industry‐standard ceramic packages) an output power beyond 100 W is achieved with a PAE above 50% and a linear gain around 15 dB. Dual‐stage MMICs in microstrip transmission line technology yield a power added efficiency of 40% at 8.56 GHz for a power level of 11 W. A single‐stage MMIC yields a PAE of 46% with 7 W of output power atVDS= 28 V. Reliability is tested on HEMT devices having a gate periphery of 8 × 60 μm at an operating bias of 50 V under both DC and RF conditions. About 10% drain‐current change under DC‐stress (50 mA/mm) is observed after more than 1000 h of operation with an extrapolated drain‐current degradation below 20% after 200000 h (more than 20 years) of operation. Under RF stress (2 GHz, 1 dB compression) the observed change in output power density is below 0.2 dB after more than 1000 h.