MHMiroslav Husak

Miroslav Husak

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Miroslav Husak has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Micro Power Supply Based on Piezoelectric Effect

    by M. Husak, A. Budkova, T. Pycha, A. Laposa, V. Povolny, V. Janicek, J. Novak, A. Boura, J. Foit

    The paper solves the model of the miniature Power supply based on the piezoelectric cantilever. The aim of the future is to further hybrid integration and use of nanotechnology. Contents of the article belongs to the category of renewable energy sources with environment energy conversion into electrical energy. The work is focused on the use in small temperature differences.

  • Open Access

    Gas Sensor with Different Morphology of PANI Layer

    by Jiri Kroutil, Alexandr Laposa, Vojtech Povolny, Ladislav Klimsa, Miroslav Husak

    This work presents the design of a polymer-film-based sensor for gas detection. Different types of polyaniline are used as active layers. The advantages of resistive sensors with PANI layers are easy preparation and low production cost. At room temperature, polymer films have a high sensitivity to gas concentrations. The developed sensor works on the idea of electrical resistance shifting with gas concentration. Three different polymerization solutions are employed to synthesize the polyaniline (PANI) active layers (aqueous solution, sulfuric acid solution, and acetic acid solution). Active layers are evaluated in a controlled environment for their ability to detect ammonia, carbon monoxide, nitrogen monoxide, acetone, toluene, and relative humidity in synthetic air. PANI layers polymerized in acetic acid solutions exhibit good sensitivity toward ammonia.


  • Open Access

    Hydrogen-Terminated Diamond Surface as a Gas Sensor: A Comparative Study of Its Sensitivities

    by Michal Kočí, Alexander Kromka, Adam Bouřa, Ondrej Szabó, Miroslav Husák

    A nanocrystalline diamond (NCD) layer is used as an active (sensing) part of a conductivity gas sensor. The properties of the sensor with an NCD with H-termination (response and time characteristic of resistance change) are measured by the same equipment with a similar setup and compared with commercial sensors, a conductivity sensor with a metal oxide (MOX) active material (resistance change), and an infrared pyroelectric sensor (output voltage change) in this study. The deposited layer structure is characterized and analyzed by Scanning Electron Microscopy (SEM) and Raman spectroscopy. Electrical properties (resistance change for conductivity sensors and output voltage change for the IR pyroelectric sensor) are examined for two types of gases, oxidizing (NO2) and reducing (NH3). The parameters of the tested sensors are compared and critically evaluated. Subsequently, differences in the gas sensing principles of these conductivity sensors, namely H-terminated NCD and SnO2, are described.


  • Comparison of MOSFET Gate Waffle Patterns Based on Specific On-Resistance

    by P. Vacula, V. Kote, D. Barri, M. Vacula, M. Husak, J. Jakovenko, S. Privitera


  • Open Access

    A True Random Number Generator with Time Multiplexed Sources of Randomness

    by V. Kote, P. Vacula, V. Molata, O. Vesely, O. Tlaskal, D. Barri, J. Jakovenko, M. Husak


  • Open Access

    Wirelessly Powered High-Temperature Strain Measuring Probe Based on Piezoresistive Nanocrystalline Diamond Layers

    by Adam Bouřa, Pavel Kulha, Miroslav Husák

    A high-temperature piezo-resistive nano-crystalline diamond strain sensor and wireless powering are presented in this paper. High-temperature sensors and electronic devices are required in harsh environments where the use of conventional electronic circuits is impractical or impossible. Piezo-resistive sensors based on nano-crystalline diamond layers were successfully designed, fabricated and tested. The fabricated sensors are able to operate at temperatures of up to 250°C with a reasonable sensitivity. The basic principles and applicability of wireless powering using the near magnetic field are also presented. The system is intended mainly for circuits demanding energy consumption, such as resistive sensors or devices that consist of discrete components. The paper is focused on the practical aspect and implementation of the wireless powering. The presented equations enable to fit the frequency to the optimal range and to maximize the energy and voltage transfer with respect to the coils’ properties, expected load and given geometry. The developed system uses both high-temperature active devices based on CMOS-SOI technology and strain sensors which can be wirelessly powered from a distance of up to several centimetres with the power consumption reaching hundreds of milliwatts at 200°C. The theoretical calculations are based on the general circuit theory and were performed in the software package Maple. The results were simulated in the Spice software and verified on a real sample of the measuring probe.


  • Intelligent Sensor Network for Physical Quantities Measurement

    by Miroslav Husak, Adam Boura, Vladimir Janicek

  • Vertical Velocity Measurement - Processing of Sensor Data Using Altitude Corrections

    by M. Husak, T. Vitek, A. Boura

    The system was designed for sensor measurement and data transfer. A new architecture of a multisensor system for temperature measurement using wireless communications was used in the paper. There are used sensors with digital or analog outputs. The control software of the system has been created. Different software were designed for wireless units. The integrated RF chip nRF9E5 was used as wireless units. Chip ensures wireless communication between control unit and sensors as well as wireless switch unit. The control unit controls system operation, i.e. communication, sensor data processing as well as work of actuator unit. Communication is ensured in the range of 300 m in the free space. The system was designed to operate with different type of sensors. The number of sensor can be variable. The system can used PC, PDA or mobile phone to communication with control unit.

  • Temperature Wireless Sensor Network

    by M. Husak, J. Jakovenko, T. Vitek

    The system was designed for sensor measurement and data transfer. A new architecture of a multisensor system for temperature measurement using wireless communications was used in the paper. There are used sensors with digital or analog outputs [1]. The control software of the system has been created. Different software were designed for wireless units. The integrated RF chip nRF9E5 was used as wireless units. Chip ensures wireless communication between control unit and sensors as well as wireless switch unit. The control unit controls system operation, i.e. communication, sensor data processing as well as work of actuator unit. Communication is ensured in the range of 300 m in the free space. The system was designed to operate with different type of sensors. The number of sensor can be variable. The system can used PC, PDA or mobile phone to communication with control unit [2].


  • Digitally Tunable Section for an Analog Current-Mode Predistortion

    by Adam Boura, Miroslav Husak

    The paper describes a circuit system which is able to process an analog current mode signals. It is intended to use it as a preamplifier and corrector of the transfer characteristic of some kind of sensor. The circuit is based on the sub-threshold CMOS multiplying cells. Those cells are interconnected by the current mirrors to form a circuit with desired transfer characteristic. There are two ways how to use this circuit. It can be used for direct linearization (pre-distortion) of the signal from the sensor or it can be encircled by a negative feedback in order to realize the inverse function. The circuit is dedicated for slow signals and for extremely low power applications. The transfer characteristic is tunable aid four ten-bit digital to analog converters. The program CADENCE and the CMOS 180 nm technology were used for simulations.