Adam Bouřa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adam Bouřa has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Miroslav Husak
Department of Microelectronics, Czech Technical University in Prague, Technicka 2, 166 27 Prague 6, Czech Republic
5 shared publications - Vladimir Janicek
Department of Microelectronics, Czech Technical University in Prague, Technicka 2, CZ-166 27 Prague 6, Czech Republic
2 shared publications - Alexander Kromka
Institute of Physics of the Czech Academy of Sciences Prague Czech Republic
1 shared publication - Alexandr Laposa
Department of Microelectronics, Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, 160 00 Prague, Czech Republic
1 shared publication - Jan Novák
Department of Microelectronics, Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, 160 00 Prague, Czech Republic
1 shared publication - Michal Kočí
Department of Semiconductors, Institute of Physics of the Czech Academy of Sciences, Cukrovarnická 10/112, Prague 6 162 00, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 24 November 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (11) , 115117
Optimum wavelength selection for a POF-based soil moisture sensor with a gypsum substrate
Measuring soil moisture is important in many fields. Knowing the water content of soil is particularly crucial in agriculture, plant cultivation, gardening, irrigation management, climatology and weather forecasting. However, accurately determining soil moisture levels can be challenging, and several methods are commonly employed. This paper presents a sensor based on the Fresnel total internal reflection method. It uses multimode plastic optical fibre with a stripped cladding and exposed core, which is sealed within a gypsum substrate. The presence of moisture affects its transmittance. The performance of this detection method also depends on the wavelength of the test light. The paper describes the construction of the sensor. The mechanical, optical, and electronic designs are described in detail. It presents transmittance as a function of moisture and for different wavelengths in the visible and near-infrared spectra for various soil moisture values. The results demonstrate the effectiveness of the proposed sensing method. The sensor has low power consumption and does not interact directly with the soil. This ensures minimal interaction with other sensors and electronics, as well as minimising the influence of soil mineralisation on the measurement results.
- 24 November 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (11) , 115117
Open AccessOptimum wavelength selection for a POF-based soil moisture sensor with a gypsum substrate
Measuring soil moisture is important in many fields. Knowing the water content of soil is particularly crucial in agriculture, plant cultivation, gardening, irrigation management, climatology and weather forecasting. However, accurately determining soil moisture levels can be challenging, and several methods are commonly employed. This paper presents a sensor based on the Fresnel total internal reflection method. It uses multimode plastic optical fibre with a stripped cladding and exposed core, which is sealed within a gypsum substrate. The presence of moisture affects its transmittance. The performance of this detection method also depends on the wavelength of the test light. The paper describes the construction of the sensor. The mechanical, optical, and electronic designs are described in detail. It presents transmittance as a function of moisture and for different wavelengths in the visible and near-infrared spectra for various soil moisture values. The results demonstrate the effectiveness of the proposed sensing method. The sensor has low power consumption and does not interact directly with the soil. This ensures minimal interaction with other sensors and electronics, as well as minimising the influence of soil mineralisation on the measurement results.
- 12 July 2023
- Published by Elsevier in Solar Energy
- Vol. 262
Characterization of a small amorphous photovoltaic panel and derivation of its SPICE model
- 12 July 2023
- Published by Elsevier in Solar Energy
- Vol. 262
Characterization of a small amorphous photovoltaic panel and derivation of its SPICE model
- Open Access
Hydrogen-Terminated Diamond Surface as a Gas Sensor: A Comparative Study of Its Sensitivities
A nanocrystalline diamond (NCD) layer is used as an active (sensing) part of a conductivity gas sensor. The properties of the sensor with an NCD with H-termination (response and time characteristic of resistance change) are measured by the same equipment with a similar setup and compared with commercial sensors, a conductivity sensor with a metal oxide (MOX) active material (resistance change), and an infrared pyroelectric sensor (output voltage change) in this study. The deposited layer structure is characterized and analyzed by Scanning Electron Microscopy (SEM) and Raman spectroscopy. Electrical properties (resistance change for conductivity sensors and output voltage change for the IR pyroelectric sensor) are examined for two types of gases, oxidizing (NO2) and reducing (NH3). The parameters of the tested sensors are compared and critically evaluated. Subsequently, differences in the gas sensing principles of these conductivity sensors, namely H-terminated NCD and SnO2, are described.
Open AccessHydrogen-Terminated Diamond Surface as a Gas Sensor: A Comparative Study of Its Sensitivities
A nanocrystalline diamond (NCD) layer is used as an active (sensing) part of a conductivity gas sensor. The properties of the sensor with an NCD with H-termination (response and time characteristic of resistance change) are measured by the same equipment with a similar setup and compared with commercial sensors, a conductivity sensor with a metal oxide (MOX) active material (resistance change), and an infrared pyroelectric sensor (output voltage change) in this study. The deposited layer structure is characterized and analyzed by Scanning Electron Microscopy (SEM) and Raman spectroscopy. Electrical properties (resistance change for conductivity sensors and output voltage change for the IR pyroelectric sensor) are examined for two types of gases, oxidizing (NO2) and reducing (NH3). The parameters of the tested sensors are compared and critically evaluated. Subsequently, differences in the gas sensing principles of these conductivity sensors, namely H-terminated NCD and SnO2, are described.
- 1 January 2020
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 27 (4) , 575-587
A SIMPLE AND AFFORDABLE POWERING CIRCUIT FOR IoT SENSOR NODES WITH ENERGY HARVESTING
- 1 January 2020
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 27 (4) , 575-587
A SIMPLE AND AFFORDABLE POWERING CIRCUIT FOR IoT SENSOR NODES WITH ENERGY HARVESTING
- Open Access
- 1 September 2016
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 23 (3) , 437-449
Wirelessly Powered High-Temperature Strain Measuring Probe Based on Piezoresistive Nanocrystalline Diamond Layers
A high-temperature piezo-resistive nano-crystalline diamond strain sensor and wireless powering are presented in this paper. High-temperature sensors and electronic devices are required in harsh environments where the use of conventional electronic circuits is impractical or impossible. Piezo-resistive sensors based on nano-crystalline diamond layers were successfully designed, fabricated and tested. The fabricated sensors are able to operate at temperatures of up to 250°C with a reasonable sensitivity. The basic principles and applicability of wireless powering using the near magnetic field are also presented. The system is intended mainly for circuits demanding energy consumption, such as resistive sensors or devices that consist of discrete components. The paper is focused on the practical aspect and implementation of the wireless powering. The presented equations enable to fit the frequency to the optimal range and to maximize the energy and voltage transfer with respect to the coils’ properties, expected load and given geometry. The developed system uses both high-temperature active devices based on CMOS-SOI technology and strain sensors which can be wirelessly powered from a distance of up to several centimetres with the power consumption reaching hundreds of milliwatts at 200°C. The theoretical calculations are based on the general circuit theory and were performed in the software package Maple. The results were simulated in the Spice software and verified on a real sample of the measuring probe.
- 1 September 2016
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 23 (3) , 437-449
Open AccessWirelessly Powered High-Temperature Strain Measuring Probe Based on Piezoresistive Nanocrystalline Diamond Layers
A high-temperature piezo-resistive nano-crystalline diamond strain sensor and wireless powering are presented in this paper. High-temperature sensors and electronic devices are required in harsh environments where the use of conventional electronic circuits is impractical or impossible. Piezo-resistive sensors based on nano-crystalline diamond layers were successfully designed, fabricated and tested. The fabricated sensors are able to operate at temperatures of up to 250°C with a reasonable sensitivity. The basic principles and applicability of wireless powering using the near magnetic field are also presented. The system is intended mainly for circuits demanding energy consumption, such as resistive sensors or devices that consist of discrete components. The paper is focused on the practical aspect and implementation of the wireless powering. The presented equations enable to fit the frequency to the optimal range and to maximize the energy and voltage transfer with respect to the coils’ properties, expected load and given geometry. The developed system uses both high-temperature active devices based on CMOS-SOI technology and strain sensors which can be wirelessly powered from a distance of up to several centimetres with the power consumption reaching hundreds of milliwatts at 200°C. The theoretical calculations are based on the general circuit theory and were performed in the software package Maple. The results were simulated in the Spice software and verified on a real sample of the measuring probe.
- 1 January 2011
- Published by Springer Nature
- p. 519-525
Intelligent Sensor Network for Physical Quantities Measurement
- 1 January 2011
- Published by Springer Nature
- p. 519-525
Intelligent Sensor Network for Physical Quantities Measurement
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 83-86
NMOS and PMOS Translinear Multiplying Cell for Current-Mode Signal Processing
The paper describes NMOS and PMOS translinear cell which multiplies the current signals and which can be used for the current-mode signal processing. The translinear cell consists of NMOS or PMOS transistors that are treated in the sub-threshold conduction region. In this region the transistors exhibit an exponential dependency of the drain current versus the gate voltage and thus the translinear principle can be used for description of the functionality. Operation region of the cell is limited by the validity of the exponential dependency and also by the transistors leakage currents. Significant error is also induced by the auxiliary current mirrors which are biasing the cells. Channel length modulation effect causes error of the input signals and thus the output signal is affected by the multiplicative error. The paper presents basic idea of the multiplying cell, presents results of simulations in CADENCE and also presents results of measurements on real structure composed using discrete transistors.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 83-86
NMOS and PMOS Translinear Multiplying Cell for Current-Mode Signal Processing
The paper describes NMOS and PMOS translinear cell which multiplies the current signals and which can be used for the current-mode signal processing. The translinear cell consists of NMOS or PMOS transistors that are treated in the sub-threshold conduction region. In this region the transistors exhibit an exponential dependency of the drain current versus the gate voltage and thus the translinear principle can be used for description of the functionality. Operation region of the cell is limited by the validity of the exponential dependency and also by the transistors leakage currents. Significant error is also induced by the auxiliary current mirrors which are biasing the cells. Channel length modulation effect causes error of the input signals and thus the output signal is affected by the multiplicative error. The paper presents basic idea of the multiplying cell, presents results of simulations in CADENCE and also presents results of measurements on real structure composed using discrete transistors.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-138
Vertical Velocity Measurement - Processing of Sensor Data Using Altitude Corrections
The system was designed for sensor measurement and data transfer. A new architecture of a multisensor system for temperature measurement using wireless communications was used in the paper. There are used sensors with digital or analog outputs. The control software of the system has been created. Different software were designed for wireless units. The integrated RF chip nRF9E5 was used as wireless units. Chip ensures wireless communication between control unit and sensors as well as wireless switch unit. The control unit controls system operation, i.e. communication, sensor data processing as well as work of actuator unit. Communication is ensured in the range of 300 m in the free space. The system was designed to operate with different type of sensors. The number of sensor can be variable. The system can used PC, PDA or mobile phone to communication with control unit.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-138
Vertical Velocity Measurement - Processing of Sensor Data Using Altitude Corrections
The system was designed for sensor measurement and data transfer. A new architecture of a multisensor system for temperature measurement using wireless communications was used in the paper. There are used sensors with digital or analog outputs. The control software of the system has been created. Different software were designed for wireless units. The integrated RF chip nRF9E5 was used as wireless units. Chip ensures wireless communication between control unit and sensors as well as wireless switch unit. The control unit controls system operation, i.e. communication, sensor data processing as well as work of actuator unit. Communication is ensured in the range of 300 m in the free space. The system was designed to operate with different type of sensors. The number of sensor can be variable. The system can used PC, PDA or mobile phone to communication with control unit.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 1391-1394
Digitally Tunable Section for an Analog Current-Mode Predistortion
The paper describes a circuit system which is able to process an analog current mode signals. It is intended to use it as a preamplifier and corrector of the transfer characteristic of some kind of sensor. The circuit is based on the sub-threshold CMOS multiplying cells. Those cells are interconnected by the current mirrors to form a circuit with desired transfer characteristic. There are two ways how to use this circuit. It can be used for direct linearization (pre-distortion) of the signal from the sensor or it can be encircled by a negative feedback in order to realize the inverse function. The circuit is dedicated for slow signals and for extremely low power applications. The transfer characteristic is tunable aid four ten-bit digital to analog converters. The program CADENCE and the CMOS 180 nm technology were used for simulations.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 1391-1394
Digitally Tunable Section for an Analog Current-Mode Predistortion
The paper describes a circuit system which is able to process an analog current mode signals. It is intended to use it as a preamplifier and corrector of the transfer characteristic of some kind of sensor. The circuit is based on the sub-threshold CMOS multiplying cells. Those cells are interconnected by the current mirrors to form a circuit with desired transfer characteristic. There are two ways how to use this circuit. It can be used for direct linearization (pre-distortion) of the signal from the sensor or it can be encircled by a negative feedback in order to realize the inverse function. The circuit is dedicated for slow signals and for extremely low power applications. The transfer characteristic is tunable aid four ten-bit digital to analog converters. The program CADENCE and the CMOS 180 nm technology were used for simulations.
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 173-176
Translinear Subthreshold MOS Filter for the Wireless Sensors Applications
The work describes a design of the filter using log-domain CMOS technology. Filter only consists of capacitances and CMOS transistors in the week inversion mode and they are treated in the subthreshold conduction region. Low-pass, band-pass and high-pass filter is considered in the design. The transfer function of the filter is determined by the feedback around its input and output. My design is based on demand to have a universal building block which is able to filter the frequency band from DC to radio frequencies. This building block is represented by the log-domain differentiator. The frequency band and the transfer function of the filter is determined only aid few devices connected to this building block. It is intended to use these current-mode filters in the design of the wireless sensor systems. In these applications the low-pass filters are usually used as an antialiasing filter before the signal is sampled. Also the radio frequency part of the circuit uses the filters. The program CADENCE and 0.18 mum CMOS technology were used for simulations
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 173-176
Translinear Subthreshold MOS Filter for the Wireless Sensors Applications
The work describes a design of the filter using log-domain CMOS technology. Filter only consists of capacitances and CMOS transistors in the week inversion mode and they are treated in the subthreshold conduction region. Low-pass, band-pass and high-pass filter is considered in the design. The transfer function of the filter is determined by the feedback around its input and output. My design is based on demand to have a universal building block which is able to filter the frequency band from DC to radio frequencies. This building block is represented by the log-domain differentiator. The frequency band and the transfer function of the filter is determined only aid few devices connected to this building block. It is intended to use these current-mode filters in the design of the wireless sensor systems. In these applications the low-pass filters are usually used as an antialiasing filter before the signal is sampled. Also the radio frequency part of the circuit uses the filters. The program CADENCE and 0.18 mum CMOS technology were used for simulations