Athanasios Scarpas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Athanasios Scarpas has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Xueyan Liu
Section of Pavement Engineering, Department of Engineering Structures, Faculty of Civil Engineering and Geosciences, Delft University of Technology, Stevinweg 1, 2628 CN Delft, the Netherlands
7 shared publications - Panos Apostolidis
Section of Pavement Engineering, Faculty of Civil Engineering and Geosciences, Delft University of Technology, Delft, The Netherlands
4 shared publications Xueyan Liu
Pavement Engineering, Delft University of Technology, Delft, The Netherlands
4 shared publications- Aikaterini Varveri
Delft University of Technology
3 shared publications Sandra Erkens
Pavement Engineering, Delft University of Technology, Delft, The Netherlands
3 shared publications- Cor Kasbergen
Section of Structural Mechanics, Faculty of Civil Engineering and Geosciences, Delft University of Technology, Stevinweg 1, 2628 CN Delft, The Netherlands
2 shared publications
Latest Publications
- Open Access
- 27 August 2021
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2675 (12) , 1138-1149
Differences in the Ageing Behavior of Asphalt Pavements with Porous and Stone Mastic Asphalt Mixtures
The degradation of bituminous materials as a result of ageing has a significant effect on asphalt pavement performance. In this study, one porous asphalt (PA) section and one stone mastic asphalt (SMA) asphalt pavement section were designed and constructed in 2014 and exposed to the actual environmental condition. To study the change in the pavement’s mechanical properties, asphalt cores were collected from both test sections annually. The change in stiffness modulus was determined via cyclic indirect tensile tests. To investigate the ageing behavior across the pavement depth, the bitumen was extracted and recovered from 13 mm slices along the depths of the cores. The chemical composition and rheological properties of the field-recovered bitumen, and that of original bitumen aged in standard short- and long-term ageing protocols, were investigated by means of the Fourier Transform Infrared (FTIR) spectrometer and Dynamic Shear Rheometer. The results show that the effect of mineral aggregate packing, and therefore of air-void distribution and connectivity, on the ageing sensitivity of the pavements with time was significant, as the changes in the stiffness of the PA mixture were greater than that of SMA mixture. In addition, the results of field-recovered bitumen show that there is an ageing gradient inside the porous asphalt layer, however, the ageing of SMA mainly happens on the surface of the layer. Finally, the field-recovered and laboratory-aged bitumen results demonstrate a weak relation between field and standard laboratory ageing protocols.
- 27 August 2021
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2675 (12) , 1138-1149
Open AccessDifferences in the Ageing Behavior of Asphalt Pavements with Porous and Stone Mastic Asphalt Mixtures
The degradation of bituminous materials as a result of ageing has a significant effect on asphalt pavement performance. In this study, one porous asphalt (PA) section and one stone mastic asphalt (SMA) asphalt pavement section were designed and constructed in 2014 and exposed to the actual environmental condition. To study the change in the pavement’s mechanical properties, asphalt cores were collected from both test sections annually. The change in stiffness modulus was determined via cyclic indirect tensile tests. To investigate the ageing behavior across the pavement depth, the bitumen was extracted and recovered from 13 mm slices along the depths of the cores. The chemical composition and rheological properties of the field-recovered bitumen, and that of original bitumen aged in standard short- and long-term ageing protocols, were investigated by means of the Fourier Transform Infrared (FTIR) spectrometer and Dynamic Shear Rheometer. The results show that the effect of mineral aggregate packing, and therefore of air-void distribution and connectivity, on the ageing sensitivity of the pavements with time was significant, as the changes in the stiffness of the PA mixture were greater than that of SMA mixture. In addition, the results of field-recovered bitumen show that there is an ageing gradient inside the porous asphalt layer, however, the ageing of SMA mainly happens on the surface of the layer. Finally, the field-recovered and laboratory-aged bitumen results demonstrate a weak relation between field and standard laboratory ageing protocols.
- Open Access
- 25 March 2021
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 22 (sup1) , S251-S268
Micromechanics-based complex modulus prediction of crumb rubber modified bitumen considering interparticle interactions
Crumb rubber modified bitumen (CRMB) can be regarded as a binary composite system in which swollen rubber particles are embedded in the bitumen matrix. The current study aims to further improve the prediction accuracy of micromechanical models for CRMB by considering the interparticle interactions. To accomplish this goal, two different strategies were used. Firstly, the (n+1)-phase model was applied to the CRMB system by considering the multilayer properties of swollen rubber particles. Secondly, a new micromechanical scheme called the J-C model was used to account for the interparticle interaction issue. Results show that the (n+1)-phase models slightly increase the prediction accuracy but the underestimation of complex modulus at lower frequencies remains unsolved. The J-C model remedies the underestimation of modulus in the low-frequency range by other models and provides an overall improvement for the relative prediction accuracy by properly addressing the interparticle interactions from the perspective of particle configuration.
- 25 March 2021
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 22 (sup1) , S251-S268
Open AccessMicromechanics-based complex modulus prediction of crumb rubber modified bitumen considering interparticle interactions
Crumb rubber modified bitumen (CRMB) can be regarded as a binary composite system in which swollen rubber particles are embedded in the bitumen matrix. The current study aims to further improve the prediction accuracy of micromechanical models for CRMB by considering the interparticle interactions. To accomplish this goal, two different strategies were used. Firstly, the (n+1)-phase model was applied to the CRMB system by considering the multilayer properties of swollen rubber particles. Secondly, a new micromechanical scheme called the J-C model was used to account for the interparticle interaction issue. Results show that the (n+1)-phase models slightly increase the prediction accuracy but the underestimation of complex modulus at lower frequencies remains unsolved. The J-C model remedies the underestimation of modulus in the low-frequency range by other models and provides an overall improvement for the relative prediction accuracy by properly addressing the interparticle interactions from the perspective of particle configuration.
- Open Access
- 1 July 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 250
Use of epoxy asphalt as surfacing and tack coat material for roadway pavements
- 1 July 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 250
Open AccessUse of epoxy asphalt as surfacing and tack coat material for roadway pavements
- Open Access
- 1 July 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 249
Characterization of epoxy-asphalt binders by differential scanning calorimetry
- 1 July 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 249
Open AccessCharacterization of epoxy-asphalt binders by differential scanning calorimetry
- Open Access
- 20 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (11) , 2308
Induction Heating-Assisted Compaction in Porous Asphalt Pavements: A Computational Study
Low temperature asphalt (LTA) technologies, such as warm-mixed asphalt mixes, are utilized in the paving industry to lower energy demands and greenhouse gas emissions during asphalt mixing and pavement construction. However, the asphalt mixes developed that incorporate LTA additives are more sensitive than hot-mixed asphalts to temperature reduction during compaction, which leads to inadequate compaction and subsequent poor pavement performance. The induction heating-assisted compaction of pavement structures appears to be an effective way to ameliorate such issues and to improve mix compactability at lower temperatures. Considering that induction-assisted compaction is a complex process, a computational methodology is proposed in this paper. A porous asphalt concrete mix was considered as case material. For the pavement compaction analyses after induction, the temperature field generated by electromagnetic induction was predicted and the material parameters of asphalt mortar were adjusted. The effect of induction heating on asphalt compaction effectiveness, the tendency of mix density changing, the increase in compactor passes, and the influence of temperature on compaction at different locations in the pavement were studied as well.
- 20 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (11) , 2308
Open AccessInduction Heating-Assisted Compaction in Porous Asphalt Pavements: A Computational Study
Low temperature asphalt (LTA) technologies, such as warm-mixed asphalt mixes, are utilized in the paving industry to lower energy demands and greenhouse gas emissions during asphalt mixing and pavement construction. However, the asphalt mixes developed that incorporate LTA additives are more sensitive than hot-mixed asphalts to temperature reduction during compaction, which leads to inadequate compaction and subsequent poor pavement performance. The induction heating-assisted compaction of pavement structures appears to be an effective way to ameliorate such issues and to improve mix compactability at lower temperatures. Considering that induction-assisted compaction is a complex process, a computational methodology is proposed in this paper. A porous asphalt concrete mix was considered as case material. For the pavement compaction analyses after induction, the temperature field generated by electromagnetic induction was predicted and the material parameters of asphalt mortar were adjusted. The effect of induction heating on asphalt compaction effectiveness, the tendency of mix density changing, the increase in compactor passes, and the influence of temperature on compaction at different locations in the pavement were studied as well.
- Open Access
- 13 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (11) , 2231
The Effect of Ageing on Chemical and Mechanical Properties of Asphalt Mortar
Asphalt mortar is a mixture of bitumen, filler, and sand. Mortar plays an important role in asphalt mixtures as it serves as the adhesive between the coarser aggregates. Due to the effect of bitumen ageing, the chemical and mechanical properties of asphalt mortar evolve with time. The mortar becomes more brittle and prone to cracking, thus leading to inferior pavement performance. In this study, Fourier transform infrared (FTIR) spectrometry was used to quantify changes in the chemical functional groups related to ageing and to calculate the carbonyl and sulfoxide indices. In addition, frequency sweep tests and uniaxial tension tests were performed by means of dynamic shear rheometer (DSR) tests to determine evolution of the stiffness and strength due to ageing. Two different oven ageing protocols were used to evaluate the effect of fine mineral particles on bitumen ageing. The protocols differed with respect to the order of ageing and mixing of the constituents. The results showed that both the chemical and mechanical properties of mortars significantly changed with ageing. Specifically, the carbonyl index, stiffness, and strength of the mortar increased. Under the same ageing conditions, a higher ageing level was observed for mortars produced by first mixing and then ageing compared to the mortars produced by mixing aged bitumen with filler and sand. This could be due to the presence of sand and filler particles, which resulted in an increased length of diffusion paths and consequently a slower ageing process.
- 13 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (11) , 2231
Open AccessThe Effect of Ageing on Chemical and Mechanical Properties of Asphalt Mortar
Asphalt mortar is a mixture of bitumen, filler, and sand. Mortar plays an important role in asphalt mixtures as it serves as the adhesive between the coarser aggregates. Due to the effect of bitumen ageing, the chemical and mechanical properties of asphalt mortar evolve with time. The mortar becomes more brittle and prone to cracking, thus leading to inferior pavement performance. In this study, Fourier transform infrared (FTIR) spectrometry was used to quantify changes in the chemical functional groups related to ageing and to calculate the carbonyl and sulfoxide indices. In addition, frequency sweep tests and uniaxial tension tests were performed by means of dynamic shear rheometer (DSR) tests to determine evolution of the stiffness and strength due to ageing. Two different oven ageing protocols were used to evaluate the effect of fine mineral particles on bitumen ageing. The protocols differed with respect to the order of ageing and mixing of the constituents. The results showed that both the chemical and mechanical properties of mortars significantly changed with ageing. Specifically, the carbonyl index, stiffness, and strength of the mortar increased. Under the same ageing conditions, a higher ageing level was observed for mortars produced by first mixing and then ageing compared to the mortars produced by mixing aged bitumen with filler and sand. This could be due to the presence of sand and filler particles, which resulted in an increased length of diffusion paths and consequently a slower ageing process.
- Open Access
- 29 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (10) , 1760
Non-Newtonian Behaviors of Crumb Rubber-Modified Bituminous Binders
Crumb rubber-modified bitumen (CRMB) has been utilized in the asphalt paving industry for decades due to its various benefits. The complex interaction between bitumen and crumb rubber as well as the addition of warm-mix additives makes the typical laws of Newtonian fluids insufficient to describe the behaviors of highly modified bituminous binders. To systematically explore the non-Newtonian behaviors of CRMB, a dynamic shear rheometer was utilized to apply shear loading on the samples at various temperatures and shear rates. Results show that the viscosity of different binders are highly temperature- and shear rate-dependent, while highly modified binders exhibit more obvious shear-thinning behaviors at certain temperatures. With the help of zero shear viscosity and yield stress, the shear-thinning behaviors of non-Newtonian binders can be sufficiently characterized. The Arrhenius equation is invalid to describe viscosity-temperature characteristics of bitumen in the non-Newtonian region. A second-order polynomial function was proposed to characterize the viscosity-temperature dependence with a high correlation degree.
- 29 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (10) , 1760
Open AccessNon-Newtonian Behaviors of Crumb Rubber-Modified Bituminous Binders
Crumb rubber-modified bitumen (CRMB) has been utilized in the asphalt paving industry for decades due to its various benefits. The complex interaction between bitumen and crumb rubber as well as the addition of warm-mix additives makes the typical laws of Newtonian fluids insufficient to describe the behaviors of highly modified bituminous binders. To systematically explore the non-Newtonian behaviors of CRMB, a dynamic shear rheometer was utilized to apply shear loading on the samples at various temperatures and shear rates. Results show that the viscosity of different binders are highly temperature- and shear rate-dependent, while highly modified binders exhibit more obvious shear-thinning behaviors at certain temperatures. With the help of zero shear viscosity and yield stress, the shear-thinning behaviors of non-Newtonian binders can be sufficiently characterized. The Arrhenius equation is invalid to describe viscosity-temperature characteristics of bitumen in the non-Newtonian region. A second-order polynomial function was proposed to characterize the viscosity-temperature dependence with a high correlation degree.
- 1 June 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 144 (2) , 04018015
Skid Resistance Characteristics of Asphalt Pavements in Hot Climates
This research assesses the influence of temperature variation on GripTester (Findlay Irvine, Penicuik, Scotland) skid resistance measurements of asphalt pavements in Qatar. It evaluated a test road with six different sections and four major highways during winter and summer seasons with ambient temperature ranging from 18 to 44°C. Close-range photogrammetry (CRP) was employed for surface texture analysis using multiple pavement surface images and proprietary software. Differences in binder type and mixture design of the test road sections did not cause significant differences in skid resistance. The south–north (SN) direction of the test road had lower friction values during summer than winter. The opposite was the case for the north–south (NS) direction. The average friction and corresponding texture parameters in the NS direction were respectively 1.4 and 1.2 times higher than in the SN direction. The major highways generally had lower friction in summer than the following winter despite traffic polishing over time. The results suggest that the effect of temperature on skid resistance becomes pronounced when the grip number drops below 0.30 and surface texture decreases.
- 1 June 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 144 (2) , 04018015
Skid Resistance Characteristics of Asphalt Pavements in Hot Climates
This research assesses the influence of temperature variation on GripTester (Findlay Irvine, Penicuik, Scotland) skid resistance measurements of asphalt pavements in Qatar. It evaluated a test road with six different sections and four major highways during winter and summer seasons with ambient temperature ranging from 18 to 44°C. Close-range photogrammetry (CRP) was employed for surface texture analysis using multiple pavement surface images and proprietary software. Differences in binder type and mixture design of the test road sections did not cause significant differences in skid resistance. The south–north (SN) direction of the test road had lower friction values during summer than winter. The opposite was the case for the north–south (NS) direction. The average friction and corresponding texture parameters in the NS direction were respectively 1.4 and 1.2 times higher than in the SN direction. The major highways generally had lower friction in summer than the following winter despite traffic polishing over time. The results suggest that the effect of temperature on skid resistance becomes pronounced when the grip number drops below 0.30 and surface texture decreases.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30 (3)
Effects of Different Aging Methods on Chemical and Rheological Properties of Bitumen
Bitumen undergoes ageing, which leads to changes in its chemical and rheological properties, causing it to become harder and more brittle with time. This study aims to compare the effects of different laboratory ageing methods on the chemistry and rheology of three bitumen types: a Pen , a Pen , and a polymer-modified bitumen (PmB). Four ageing protocols were applied: ageing at room temperature, oven ageing, pressure ageing vessel (PAV), and rolling thin-film oven test (RTFOT) combined with PAV ageing. The effects of temperature, pressure, and ageing time were studied using dynamic shear tests and infrared spectroscopy. The results highlight the relationship between chemistry and rheology of bitumen. Bitumen hardening, which was revealed by an increase in complex modulus and a decrease in phase angle, was reflected in the growth of specific chemical functional groups. Among all materials, soft bitumen showed the greater tendency to oxidize. Different behavior was observed for PmB, which presented the highest resistance against oxidation among the studied bitumens, even though the reaction with oxygen caused the deterioration of the added polymer modifiers.- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30 (3)
Effects of Different Aging Methods on Chemical and Rheological Properties of Bitumen
Bitumen undergoes ageing, which leads to changes in its chemical and rheological properties, causing it to become harder and more brittle with time. This study aims to compare the effects of different laboratory ageing methods on the chemistry and rheology of three bitumen types: a Pen , a Pen , and a polymer-modified bitumen (PmB). Four ageing protocols were applied: ageing at room temperature, oven ageing, pressure ageing vessel (PAV), and rolling thin-film oven test (RTFOT) combined with PAV ageing. The effects of temperature, pressure, and ageing time were studied using dynamic shear tests and infrared spectroscopy. The results highlight the relationship between chemistry and rheology of bitumen. Bitumen hardening, which was revealed by an increase in complex modulus and a decrease in phase angle, was reflected in the growth of specific chemical functional groups. Among all materials, soft bitumen showed the greater tendency to oxidize. Different behavior was observed for PmB, which presented the highest resistance against oxidation among the studied bitumens, even though the reaction with oxygen caused the deterioration of the added polymer modifiers.- 1 January 2015
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2525 (1) , 79-90
Study of Influence of Operating Parameters on Braking Friction and Rolling Resistance
Tire–road interaction addresses safety with respect to braking friction and energy efficiency in the context of rolling resistance. These phenomena are coherent, but their engineering solutions can be contradictory. For example, highly skid-resistant surfaces may not be ideal for fuel economy, but surfaces with low rolling resistance may be prone to skidding. Several experimental and numerical studies have investigated the individual phenomena, but insufficient attention has been paid to studying them coherently. The present study computed braking friction and rolling resistance for various operating parameters and their coherent response for each parameter with the use of a thermomechanical contact algorithm. Micromechanical finite element simulations of a rolling or braking pneumatic tire against selected asphalt concrete surfaces were performed for various operating conditions, such as tire load, inflation pressure, speed, and ambient air and pavement temperatures. The coefficients of braking friction and rolling resistance were found to decrease with the inflation pressure and the temperature and to increase with the wheel load. The braking friction coefficient was found to decrease with the speed, in contrast to the rolling resistance coefficient, which increases with the same parameter. A full-skidding tire registered lower braking friction than a 20% slipping tire. Also, an asphalt surface with higher macrotexture offered higher braking friction and higher rolling resistance, and vice versa.
- 1 January 2015
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2525 (1) , 79-90
Study of Influence of Operating Parameters on Braking Friction and Rolling Resistance
Tire–road interaction addresses safety with respect to braking friction and energy efficiency in the context of rolling resistance. These phenomena are coherent, but their engineering solutions can be contradictory. For example, highly skid-resistant surfaces may not be ideal for fuel economy, but surfaces with low rolling resistance may be prone to skidding. Several experimental and numerical studies have investigated the individual phenomena, but insufficient attention has been paid to studying them coherently. The present study computed braking friction and rolling resistance for various operating parameters and their coherent response for each parameter with the use of a thermomechanical contact algorithm. Micromechanical finite element simulations of a rolling or braking pneumatic tire against selected asphalt concrete surfaces were performed for various operating conditions, such as tire load, inflation pressure, speed, and ambient air and pavement temperatures. The coefficients of braking friction and rolling resistance were found to decrease with the inflation pressure and the temperature and to increase with the wheel load. The braking friction coefficient was found to decrease with the speed, in contrast to the rolling resistance coefficient, which increases with the same parameter. A full-skidding tire registered lower braking friction than a 20% slipping tire. Also, an asphalt surface with higher macrotexture offered higher braking friction and higher rolling resistance, and vice versa.