Wadia Dhaoui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wadia Dhaoui has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Hedi Zarrouk
Chemistry Department, Faculty of Sciences, University of Tunis El Manar, 2092 Tunis, Tunisia
2 shared publicationsAbdellatif Belhaj Mohamed
Laboratory of Photovoltaics and Semiconductors , National Institute of Scientific and Technical Research , Tunis , Tunisia
1 shared publication- Adam Pron
Warsaw University of Technology, Faculty of Chemistry, Noakowskiego 3, 00-664 Warsaw, Poland
1 shared publication - Amal Bourguiba
Mechanics and Civil Engineering Materials Laboratory, University of Cergy Pontoise, 5Mail Gay-Lussac, Neuville sur Oise, 95031, Cergy Pontoise Cedex
1 shared publication - Elhem Ghorbel
Laboratoire de Mécanique et Matériaux de Génie Civil (L2MGC), Cergy-Pontoise University, Paris, France
1 shared publication Hafedh Ben Ouada
Laboratory of Physical Interfaces, Faculty of Sciences, University of Monastir, 5000 Monastir, Tunisia
1 shared publication
Latest Publications
- 1 September 2019
- Published by Springer Nature in Chemistry Africa
- Vol. 2 (3) , 383-394
Correlation Between Morphology Control and Photocatalytic Performance of BiOBr Nano-Microstrutures
- 1 September 2019
- Published by Springer Nature in Chemistry Africa
- Vol. 2 (3) , 383-394
Correlation Between Morphology Control and Photocatalytic Performance of BiOBr Nano-Microstrutures
- 17 September 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 843-852
Epoxy Resin/Recycled Sand Mortars’ Resistance to Chloride Ions Diffusion
This work aims to study the possibility of using recycled sand to prepare an epoxy resin mortar mechanically resistant and resistant against chloride ions diffusion. Comparative studies were performed on standardized hydraulic mortar and epoxy / standardized sand. The effect of the incorporation of a thinner, methyl octanoate, on the workability, mechanical properties and durability of the epoxy resin mortar is analyzed. It appears from this study that investigated mortars have a workability which is improved with the increase in the percentage of resin and with the addition of thinner. The total substitution of standardized sand by recycled sand alters this property. The resin mortar have a lower porosity than the hydraulic mortar, better mechanical properties and better resistance to chloride ions diffusion regardless of sand nature. The total substitution of standardized sand by recycled sand does not significantly affect the mechanical properties of resin mortars having the same binder percentages (20%). However, it causes a slight decrease in the resistance to chloride ions diffusion attributed to a higher total porosity accessible to water for recycled sand mortar. Similarly, the migration of these ions into mortar decreases with increasing the resin percentage, decrease attributed to the lowering of total porosity. Thinner addition affects the apparent diffusion coefficient.
- 17 September 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 843-852
Epoxy Resin/Recycled Sand Mortars’ Resistance to Chloride Ions Diffusion
This work aims to study the possibility of using recycled sand to prepare an epoxy resin mortar mechanically resistant and resistant against chloride ions diffusion. Comparative studies were performed on standardized hydraulic mortar and epoxy / standardized sand. The effect of the incorporation of a thinner, methyl octanoate, on the workability, mechanical properties and durability of the epoxy resin mortar is analyzed. It appears from this study that investigated mortars have a workability which is improved with the increase in the percentage of resin and with the addition of thinner. The total substitution of standardized sand by recycled sand alters this property. The resin mortar have a lower porosity than the hydraulic mortar, better mechanical properties and better resistance to chloride ions diffusion regardless of sand nature. The total substitution of standardized sand by recycled sand does not significantly affect the mechanical properties of resin mortars having the same binder percentages (20%). However, it causes a slight decrease in the resistance to chloride ions diffusion attributed to a higher total porosity accessible to water for recycled sand mortar. Similarly, the migration of these ions into mortar decreases with increasing the resin percentage, decrease attributed to the lowering of total porosity. Thinner addition affects the apparent diffusion coefficient.
- 1 July 2006
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 11 (3) , 239-252
Investigation of Spectral Properties, Thermal Stability, and Morphology in Polyaniline Doped with Chlorocarboxylic Acids
The morphology of polyaniline (PANI), granular or tubular, depends on the acidity conditions during the reaction rather than on the chemical nature of the acid. In reference to acetic acid in which media nanotubes had been observed, dichloroacetic acid (DCA) and trichloroacetic acid (TCA) were used to synthesize polyaniline by the oxidative polymerization technique. Characterization by Fourier-transform infrared (FTIR), UV-visible, and electron paramagnetic (EPR) spectroscopy techniques indicated that the polymers are in the protonated emeraldine form and suggest that the protonation of PANI in media containing such acids was achieved with the help of sulfuric acid produced during the reaction from ammonium peroxydisulfate. The conductivity of polyaniline prepared in DCA was 0.04 S cm−1 and 0.5 S cm−1 in TCA. The thermal stability of polyaniline salts was tested by thermogravimetric analysis and a three-step decomposition pattern was observed. Wide-angle X-ray diffraction (WAXD) study showed enhanced crystallinity in polyaniline prepared in TCA. The morphology is discussed in relation to the formation of polyaniline nanotubes reported in the literature.
- 1 July 2006
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 11 (3) , 239-252
Investigation of Spectral Properties, Thermal Stability, and Morphology in Polyaniline Doped with Chlorocarboxylic Acids
The morphology of polyaniline (PANI), granular or tubular, depends on the acidity conditions during the reaction rather than on the chemical nature of the acid. In reference to acetic acid in which media nanotubes had been observed, dichloroacetic acid (DCA) and trichloroacetic acid (TCA) were used to synthesize polyaniline by the oxidative polymerization technique. Characterization by Fourier-transform infrared (FTIR), UV-visible, and electron paramagnetic (EPR) spectroscopy techniques indicated that the polymers are in the protonated emeraldine form and suggest that the protonation of PANI in media containing such acids was achieved with the help of sulfuric acid produced during the reaction from ammonium peroxydisulfate. The conductivity of polyaniline prepared in DCA was 0.04 S cm−1 and 0.5 S cm−1 in TCA. The thermal stability of polyaniline salts was tested by thermogravimetric analysis and a three-step decomposition pattern was observed. Wide-angle X-ray diffraction (WAXD) study showed enhanced crystallinity in polyaniline prepared in TCA. The morphology is discussed in relation to the formation of polyaniline nanotubes reported in the literature.