KWKimberly A. Warren

Kimberly A. Warren

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kimberly A. Warren has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Three-Year Evaluation of Thermally Induced Strain and Corresponding Lateral End Pressures for a GRS IBS in Ohio

    by K. A. Warren, M. J. Whelan, J. Hite, M. Adams

    Geosynthetic-reinforced soil (GRS) integrated bridge systems (IBS) integrate conventional bridge superstructures with a GRS abutment foundation and GRS approach for a cost-effective, rapid construction alternative. A 42.7 m long single span GRS IBS was constructed and instrumented to monitor the thermally induced behaviors and better understand the interaction between the superstructure and substructure within the limits of this system. Strain gauges were attached to the steel girders, and lateral end pressures were monitored using earth pressure cells to determine the level of stress thermally induced in the GRS approach over a 3.5 year monitoring period and evaluate the rigidity of the boundary conditions that exist at the interface. During this 3.5-year monitoring period, the data show that the GRS approach is engaged with the superstructure and experiences both active and passive lateral pressures during each thermal cycle without displaying an increase in passive pressure with time. The stress-strain data acquired during this project indicate that the GRS IBS is behaving significantly more like a system with unrestrained boundaries due to the flexibility of the GRS approach at each end. The tightly spaced reinforcements create a composite material at the ends of the superstructure that enable the approach fill to move successfully with thermally induced superstructure deformations without creating a failure within the soil or at the surface of the roadway (interface included).


  • Geosynthetic strain gage installation procedures and alternative strain measurement methods for roadway applications

    by K.A. Warren, B. Christopher, I.L. Howard

    The measurement of geosynthetic strain is important to the development of numerical models that can predict the behavior of geosynthetic-reinforced flexible pavements. This paper outlines the key issues regarding foil strain gage selection, installation, and calibration on geosynthetics for dynamic strain measurement in roadway applications. The flexible nature of geosynthetics and the interaction of these materials with the adjacent layers of the pavement structure in a dynamic loading application limit the ability to use all types of strain gages and adhesives. While this paper does not cover every type of geosynthetic, it provides sufficient procedural details and illustrations of foil strain gage installations on a variety of geosynthetics (woven geotextiles and geogrids, nonwoven geotextiles and punch/drawn geogrids) and then outlines several alternative methods (wire extensometers, inductance coils and fiber optics) of dynamic strain measurement. While foil strain gages and closely spaced wire extensometers provide a localized value of displacement on a geosynthetic, wire extensometers and inductance coils provide a measure of global displacement (which includes slack in the geosynthetic) and redundancy in total strain measurements. Fiber optics is an emerging and very promising method of accurately measuring strain in geosynthetics, and at least one delivery system has been developed.


  • Preliminary Results for a GRS Integrated Bridge System Supporting a Large Single Span Bridge

    by K. A. Warren, W. Schlatter, M. Adams, T. Stabile, D. LeGrand

    In order to refine Geosynthetic Reinforced Soil Integrated Bridge System technology (developed by the FHWA), girders from a 42.7 m single span bridge were instrumented with strain gages, end pressures were measured using horizontal pressure cells, and the abutments were instrumented with vertical pressure cells and survey targets to measure girder footing and abutment wall movements. After a six month monitoring period, vertical deflections are within tolerable limits (ranging from 1.1 to 4.6 cm) and there are no visible cracks at the bridge-approach interface. The strain gages and earth pressure cells continue to collect meaningful data in terms of magnitude and trend. A change in ambient temperature causes a temperature induced strain in the steel, which affects the lateral pressure measured behind the steel girders as expected. Vertical pressures in the abutment are also affected by the thermal cycle. This paper will display the preliminary results from this project.


  • Finite-Element Modeling of Instrumented Flexible Pavements under Stationary Transient Loading

    by Isaac L. Howard, Kimberly A. Warren

    Results from a finite-element program developed in the commercial code Plaxis were compared to those from an instrumented thin flexible pavement containing multiple test sections. The model has performed reasonably well under the limited environmental conditions encountered to date. Horizontal strain in the longitudinal direction of the asphalt concrete, vertical pressure in the crushed stone, and vertical pressure in the compacted subgrade were measured for 2,100 passes of loaded single axle dump truck traffic to compare to the values calculated in the model. Necessary inputs were determined using a rigorous laboratory testing program, alongside field data from over 500 drops of a falling weight deflectometer. Key features of the finite-element model include stationary transient loading and nonlinear stress dependent characterization of the compacted subgrade and crushed stone. Highlights of the results include the model moderately overpredicted unbound layer stresses, while overpredicting asphalt strain...


  • Investigation of thin flexible pavement response between traffic and the falling weight deflectometer (FWD)

    by Isaac Howard, Kimberly Warren

    The Falling Weight Deflectometer (FWD) is commonly used to evaluate structural characteristics of pavements. The FWD simulates vehicular loads at typical highway speeds and the data is used to back-calculate layer moduli and design overlays (among other functions). In routine testing, the only data obtained is on the surface of the pavement, which leaves potentially significant behaviors within the pavement undetected. The focus of this paper is to present the analysis of a heavily instrumented, full-scale flexible pavement that was subjected to vehicular traffic and FWD loads under controlled testing conditions. Statistical analysis and finite element modeling separately demonstrated that the responses produced by the FWD were, in general, lower than those from corresponding vehicular traffic, and this behavior was more pronounced with depth. Finite element modeling resulted in traffic asphalt strain, base pressure, and subgrade pressure responses exceeding FWD responses by factors of 1.27, 1.76, and 2.43, respectively. Similarly, a statistical analysis resulted in factors of 1.36, 1.66, and 2.39, respectively. Additional analysis showed the deflection from FWD loading would have to be increased between 1.3 to 1.6 times to produce corresponding vehicular traffic stress states.


  • Innovative Data Acquisition for Heavily Instrumented Flexible Pavements

    by Isaac L. Howard, Kimberly A. Warren

    A data acquisition program was written to allow independent triggering of multiple test sections of a thin flexible pavement. A total of 129 electronic sensors were installed in 17 test sections and subjected to 2,100 truck passes over several months immediately after construction. The measured strains were highly variable in the thin flexible pavement, but the program was still able to successfully trigger each section independently. The majority of signal processing was also performed within the program, which was written in Lab VIEW 7 Express. This approach significantly reduced the amount of postprocessing effort that would have otherwise been required. The quality of the triggering approach was compared to independently collected weigh in motion data. The majority of the test sections recorded within 0.5% of the number of vehicles recorded by the weigh in motion system. Key components of all major facets of the data acquisition and programming performed are discussed in detail.


  • Techniques Used to Measure Strain on Geosynthetics in Dynamic Applications

    by Kimberly Warren, Barry Christopher, Isaac Howard

    Geosynthetics are often used to stabilize and/or reinforce flexible pavements. Heavily instrumented, full-scale field testing has been performed to investigate the behavior of geosynthetics in flexible pavement applications (under dynamic traffic loads). Geosynthetics are instrumented to collect geosynthetic strain data that will support the development of mechanistic-empirical models for pavement design. The type of gage selected, and the methods used to bond, wire, and protect a strain gage must be carefully considered to ensure strain is measured accurately under dynamic loads, and the gage survives harsh construction conditions. The purpose of this paper is to discuss key issues regarding gage selection and preparation, and detail methods used to calibrate and install foil strain gages, wire extensometers, and inductance coils for the purpose of monitoring strain on geosynthetics in full-scale, flexible pavement field tests.

  • Statistical Analysis of Unbound Subgrade Pressure Measurements

    by Isaac L. Howard, Kimberly A. Warren, Charles R. Lord

    The objective of this paper is to present statistical analysis of unbound subgrade pressure measurements. A heavily instrumented, flexible pavement was constructed and received an uncharacteristically low amount of rainfall for several months thereafter. The large amount of data acquired under the relatively constant moisture conditions during this period served as an excellent tool to analyze variability form a full scale pavement test, especially in the context of measurement redundancy and appropriate analysis techniques. The analysis presented in this paper focuses on measured subgrade pressures and is part of a more comprehensive effort to assess all pavement layers. It was shown that sensor redundancy alone may lead to erroneous conclusions if the redundancy is taken as a substitute for variability analysis. Future work aims to demonstrate optimal techniques useful for generating meaningful conclusions by incorporating sensor redundancy, measurement variability, and construction variability.

  • Preliminary Analysis Comparing Measured Responses of FWD and Traffic Data

    by Isaac L. Howard, Kimberly A. Warren

    The objective of this paper is to present findings where measured subgrade stresses from vehicular traffic and the Falling Weight Deflectometer (FWD) are compared. Both loading techniques were employed on a heavily instrumented pavement under identical conditions during a period immediately after construction. The analysis presented clearly showed that the difference in pressure response in the compacted subgrade of a thin flexible pavement was statistically significant with vehicular traffic producing higher values in every instance. FWD readings, on average, would need to be increased by a factors of 3.73 and 2.39 for the front and back axles, respectively, to prevent statistical differences from being detected. Such a large difference in pressure response is significant since the FWD is routinely used to, among many other functions, back calculate layer moduli of stress softening soils.

  • Performance Analysis of Heavily Instrumented Flexible Pavement

    by Isaac L. Howard, Kimberly A. Warren

    The objective of this paper is to present preliminary findings of a heavily instrumented flexible pavement's performance in terms of fatigue cracking and permanent deformation. The thin pavement consists of seventeen test sections, 110 structural sensors, 19 environmental sensors, two crushed stone thicknesses, six geosynthetic products, and a fine grained subgrade with soaked CBR values of 1–2. Approximately 2,100 passes of loaded single axle dump trucks applied during a period immediately after construction where miniscule rainfall was observed make up the data set considered. Asphalt Institute transfer functions and Miner's concept were used to compute damages that were compared to distress surveys taken at the test section.