Cenk Misirli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Cenk Misirli has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Ceviz
Renewable Energy Technician Program, Department of Motor Vehicles and Transportation Technologies, Keşan Vocational College, Trakya University, 22100 Keşan, Edirne, Türkiye
2 shared publications - Mumin Sahin
Trakya University
2 shared publications - Sencer Süreyya Karabeyoğlu
KIRKLARELİ ÜNİVERSİTES
2 shared publications Can Guler
Edirne, Turkey
1 shared publication- Cem S. Cetinarslan
Edirne, Turkey
1 shared publication Halil Kılıç
Machine Deparment , Kirklareli Universitesi , 39020 , Kirklareli , Türkiye
1 shared publication
Latest Publications
- 1 February 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (2) , 258-266
Effect of high temperatures on dry sliding friction and wear behaviour of CuCrZr copper alloy
Dry friction and wear behavior at high temperatures was investigated against an Al2O3 ball in order to characterize the wear rate, coefficient of friction (COF), hardness and thermal friction behavior at different temperatures in the wear-treated zones of the CuCrZr copper alloy. Experiments were fulfilled using a pin-on-disk wear device with the aid of a temperature modulated wear device at room temperature, 100, 200 and 300 °C. The loads applied during wear are given as 3N, 5N and 7N, respectively. In order to examine the morphological structure of the worn surfaces, appropriate samples were prepared and SEM (scanning electron microscopy) device was used. Similarly, EDS (energy dispersive x-ray spectrometry) was applied to worn surfaces to examine the abrasive-material interaction. Against the hardness of the material at 25 °C, the hardness value in measurements at 300 °C showed a small increase. The COF value increased at 100 °C and then decreased, while the wear rate increased significantly as the temperature increased. The temperature increase starting from RT up to 300 °C weakened the internal structure of the CuCrZr alloy and caused an increase in the wear rate. XRD test was used to show the phases that may occur in CuCrZr alloy due to temperature and heat treatment.
- 1 February 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (2) , 258-266
Effect of high temperatures on dry sliding friction and wear behaviour of CuCrZr copper alloy
Dry friction and wear behavior at high temperatures was investigated against an Al2O3 ball in order to characterize the wear rate, coefficient of friction (COF), hardness and thermal friction behavior at different temperatures in the wear-treated zones of the CuCrZr copper alloy. Experiments were fulfilled using a pin-on-disk wear device with the aid of a temperature modulated wear device at room temperature, 100, 200 and 300 °C. The loads applied during wear are given as 3N, 5N and 7N, respectively. In order to examine the morphological structure of the worn surfaces, appropriate samples were prepared and SEM (scanning electron microscopy) device was used. Similarly, EDS (energy dispersive x-ray spectrometry) was applied to worn surfaces to examine the abrasive-material interaction. Against the hardness of the material at 25 °C, the hardness value in measurements at 300 °C showed a small increase. The COF value increased at 100 °C and then decreased, while the wear rate increased significantly as the temperature increased. The temperature increase starting from RT up to 300 °C weakened the internal structure of the CuCrZr alloy and caused an increase in the wear rate. XRD test was used to show the phases that may occur in CuCrZr alloy due to temperature and heat treatment.
- 15 October 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (5) , 1472-1477
Determination of the Change in Electrical Conductivity of Single, Bimetallic and Trimetallic Cylindrical Billets with Plastic Deformation Induced by Upsetting Process
In this study, measurement of the effect of singular, bimetallic and multimetallic materials exposed to cold plastic deformation on electrical conductivity properties was investigated. The main subject of this research is plastic deformation occurrin...
- 15 October 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (5) , 1472-1477
Determination of the Change in Electrical Conductivity of Single, Bimetallic and Trimetallic Cylindrical Billets with Plastic Deformation Induced by Upsetting Process
In this study, measurement of the effect of singular, bimetallic and multimetallic materials exposed to cold plastic deformation on electrical conductivity properties was investigated. The main subject of this research is plastic deformation occurrin...
- 19 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (9) , 2443-2451
An Investigation on Thermal Dry Sliding Wear Performance of Wrought AA 7075-T6
- 19 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (9) , 2443-2451
An Investigation on Thermal Dry Sliding Wear Performance of Wrought AA 7075-T6
- 30 August 2021
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (1) , 128-138
The Effect of Temperature on Wear Performance of High-Velocity Oxy-Fuel Sprayed WC-10Co-4Cr Coating on AA7075-T6 Substrate
- 30 August 2021
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (1) , 128-138
The Effect of Temperature on Wear Performance of High-Velocity Oxy-Fuel Sprayed WC-10Co-4Cr Coating on AA7075-T6 Substrate
- Open Access
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016560
Investigation of tribological behavior of 20NiCrBSi-WC12Co coated brake disc by HVOF method
In braking systems, which consist of dry sliding lining against a pearlitic cast-iron disc, disc wear has a significant impact on the overall wear rate. In this work, dynamometer tests were conducted to find out the friction and wear behaviour of 20NiCrBSi-WC12Co cermet coating accumulated on the cast-iron disc by High velocity oxy-fuel spraying (HVOF) and the findings were compared with those of the uncoated disc. Braking tests of the coated and uncoated discs were performed on a full-scale brake dynamometer, which was designed in line with the SAE-J2430 Brake Effectiveness Procedure. Microhardness values, surface properties, scanning electron microscopy (SEM) analysis, energy dispersive x-ray (EDX) and x-ray diffraction (XRD) analysis of the discs were evaluated. As a result of these analyses, it was found out that cermet coating had a much higher microhardness and abrasion resistance with the combination of hard WC phase and mild Ni matrix compared to the conventional disc. The coated disc exhibited stable braking effectiveness with lower surface contact temperature. At the same time, this coating results in longer service life by reducing abrasive wear on the brake disc surface and a lower lining wear rate, reducing particle matter emissions to the environment.
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016560
Open AccessInvestigation of tribological behavior of 20NiCrBSi-WC12Co coated brake disc by HVOF method
In braking systems, which consist of dry sliding lining against a pearlitic cast-iron disc, disc wear has a significant impact on the overall wear rate. In this work, dynamometer tests were conducted to find out the friction and wear behaviour of 20NiCrBSi-WC12Co cermet coating accumulated on the cast-iron disc by High velocity oxy-fuel spraying (HVOF) and the findings were compared with those of the uncoated disc. Braking tests of the coated and uncoated discs were performed on a full-scale brake dynamometer, which was designed in line with the SAE-J2430 Brake Effectiveness Procedure. Microhardness values, surface properties, scanning electron microscopy (SEM) analysis, energy dispersive x-ray (EDX) and x-ray diffraction (XRD) analysis of the discs were evaluated. As a result of these analyses, it was found out that cermet coating had a much higher microhardness and abrasion resistance with the combination of hard WC phase and mild Ni matrix compared to the conventional disc. The coated disc exhibited stable braking effectiveness with lower surface contact temperature. At the same time, this coating results in longer service life by reducing abrasive wear on the brake disc surface and a lower lining wear rate, reducing particle matter emissions to the environment.
- 30 June 2018
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 60 (6) , 647-652
Properties of Al/SiC metal matrix composites
Metal matrix composites have higher resistance compared to ceramic and polymer matrix composites. In this study, an aluminum 5754 alloy was fortified using 10 % SiC to obtain a metal matrix composite with properties superior to the original alloy. An improvement of mechanical properties was obtained by reinforcement with aluminum matrix composites which can be produced with various techniques. Mechanical properties of the composite material (Al/SiCp) were initially investigated, and then, the metallurgical properties were determined using an optical metal microscope and SEM. Furthermore, the percent of elongation, tensile strength and Vickers hardness are the input parameters for the mechanical properties. The tensile strength as an output response parameter of Al/SiCp materials was analyzed using experimental Taguchi technique design as an orthogonal array. In the present investigation, experiments were carried out to compare experimental results with predicted optimal values. ANOVA analysis rev... Kurzfassung Metallmatrix-Komposite haben eine höhere Festigkeit gegenüber keramischen und Polymermatrix-Kompositen. In der diesem Beitrag zugrunde liegenden Studie wurde die Aluminiumlegierung 5754 mit 10 % SiC verstärkt, um ein Matallmatrix-Komposit mit überragenden Eigenschaften gegenüber der ursprünglichen Legierung zu erhalten. Eine Verbesserung der mechanischen Eigenschaften kann mit der Verstärkung der Aluminiummatrix unter Nutzung verschiedener Techniken erreicht werden. Hierzu wurden die mechanischen Eigenschaften des Kompositmaterials (Al/SiCp) zunächst untersucht und dann die metallurgischen Eigenschaften mittels Licht- und Rasterelektronenmikroskopie ermittelt. Die Zusammenhänge zwischen prozentualer Dehnung, der Vickershärte und der Zugfestigkeit wurden mittels eines experimentellen Designs nach der Taguchi-Technik ermittelt, wobei ein orthogonales Array verwandt wurde. Es stellte sich heraus, dass das Kompositmaterial gegenüber statischen und dynamischen Beanspruchungen widerstandfähig ist. D...
- 30 June 2018
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 60 (6) , 647-652
Properties of Al/SiC metal matrix composites
Metal matrix composites have higher resistance compared to ceramic and polymer matrix composites. In this study, an aluminum 5754 alloy was fortified using 10 % SiC to obtain a metal matrix composite with properties superior to the original alloy. An improvement of mechanical properties was obtained by reinforcement with aluminum matrix composites which can be produced with various techniques. Mechanical properties of the composite material (Al/SiCp) were initially investigated, and then, the metallurgical properties were determined using an optical metal microscope and SEM. Furthermore, the percent of elongation, tensile strength and Vickers hardness are the input parameters for the mechanical properties. The tensile strength as an output response parameter of Al/SiCp materials was analyzed using experimental Taguchi technique design as an orthogonal array. In the present investigation, experiments were carried out to compare experimental results with predicted optimal values. ANOVA analysis rev... Kurzfassung Metallmatrix-Komposite haben eine höhere Festigkeit gegenüber keramischen und Polymermatrix-Kompositen. In der diesem Beitrag zugrunde liegenden Studie wurde die Aluminiumlegierung 5754 mit 10 % SiC verstärkt, um ein Matallmatrix-Komposit mit überragenden Eigenschaften gegenüber der ursprünglichen Legierung zu erhalten. Eine Verbesserung der mechanischen Eigenschaften kann mit der Verstärkung der Aluminiummatrix unter Nutzung verschiedener Techniken erreicht werden. Hierzu wurden die mechanischen Eigenschaften des Kompositmaterials (Al/SiCp) zunächst untersucht und dann die metallurgischen Eigenschaften mittels Licht- und Rasterelektronenmikroskopie ermittelt. Die Zusammenhänge zwischen prozentualer Dehnung, der Vickershärte und der Zugfestigkeit wurden mittels eines experimentellen Designs nach der Taguchi-Technik ermittelt, wobei ein orthogonales Array verwandt wurde. Es stellte sich heraus, dass das Kompositmaterial gegenüber statischen und dynamischen Beanspruchungen widerstandfähig ist. D...
- Open Access
- 5 December 2012
- Published by IntechOpen
Mechanical and Metalurgical Properties of Friction Welded Aluminium Joints
- 5 December 2012
- Published by IntechOpen
Open AccessMechanical and Metalurgical Properties of Friction Welded Aluminium Joints