Fabrice Giuliani
Research Subjects
Research Interests
Fabrice Giuliani has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Lukas Andracher
Institute of Aviation, Department of Engineering, University of Applied Sciences FH JOANNEUM GmbH, 8020 Graz, Austria
7 shared publications - Nina Paulitsch
Combustion Bay One e.U., Advanced Combustion Management, 8010 Graz, Austria
5 shared publications Andreas Lang
Department for Gas Turbine Combustion, Institute for Thermal Turbomachinery and Machine Dynamics, Graz University of Technology, A 8010 Graz, Austria
4 shared publications- Jakob Woisetschläger
Working Group Metrology in Turbomachinery—Laser Optical Metrology, Institute for Thermal Turbomachinery and Machine Dynamics, Graz University of Technology, 8010 Graz, Austria
4 shared publications Thomas Leitgeb
4 shared publicationsJohannes Fritzer
Department for Gas Turbine Combustion, Institute for Thermal Turbomachinery and Machine Dynamics, Graz University of Technology, A 8010 Graz, Austria
3 shared publications
Latest Publications
- 4 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-11
Combining Machine Learning, Embedded Sensor Networks and Additive Burner Design for Combustor Structural Health Monitoring
The crystAIr project is about sensitizing burners for flame monitoring based on a discrete number of dynamic pressure sensors and a machine learning approach. The context is the development of better aircraft engines and the prospect of technical solutions for hydrogen-fuelled gas turbines. The combination of sensors and appropriate signal processing is designed to mimic a “feel” for the state of the flame. The idea is to monitor the gas turbine's correct operation in real-time and anticipate impending problems such as flame blowout, combustion instability or flashback. Compared to conventional flame monitoring based on signal sampling, thresholding, bandpass analysis and time-lag measurement, this method should be less computationally intensive, more sensitive and more robust to artifacts. Not only should it be more responsive, but it should also anticipate problems based on a lessons-learned approach and outperform the conventional precursors. An unassisted machine learning method is used to achieve this. A custom-built AM burner designed for this experiment provides multiple instrumentation options. A powerful data acquisition system is setup to collect data on multiple channels, over a long time duration and at high speed to collect the learning signal chunks. The focus is on the detection of flames and, more specifically, the moment of their ignition and extinction, the operating conditions that are prone to flashback and the stability of the combustion. Additional measurement techniques are used to refine the learning method. The paper covers all these points and presents the first results.
- 4 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-11
Combining Machine Learning, Embedded Sensor Networks and Additive Burner Design for Combustor Structural Health Monitoring
The crystAIr project is about sensitizing burners for flame monitoring based on a discrete number of dynamic pressure sensors and a machine learning approach. The context is the development of better aircraft engines and the prospect of technical solutions for hydrogen-fuelled gas turbines. The combination of sensors and appropriate signal processing is designed to mimic a “feel” for the state of the flame. The idea is to monitor the gas turbine's correct operation in real-time and anticipate impending problems such as flame blowout, combustion instability or flashback. Compared to conventional flame monitoring based on signal sampling, thresholding, bandpass analysis and time-lag measurement, this method should be less computationally intensive, more sensitive and more robust to artifacts. Not only should it be more responsive, but it should also anticipate problems based on a lessons-learned approach and outperform the conventional precursors. An unassisted machine learning method is used to achieve this. A custom-built AM burner designed for this experiment provides multiple instrumentation options. A powerful data acquisition system is setup to collect data on multiple channels, over a long time duration and at high speed to collect the learning signal chunks. The focus is on the detection of flames and, more specifically, the moment of their ignition and extinction, the operating conditions that are prone to flashback and the stability of the combustion. Additional measurement techniques are used to refine the learning method. The paper covers all these points and presents the first results.
- Open Access
- 1 January 2023
- Published by European Turbomachinery Society
Recursive sequential combustion using a discrete sector approach
Recursive sequential combustion is a novel concept developed by CBOne that maximises the interaction of circulated burnt gases with the reactants in the combustor of a gas turbine to improve combustion performance. The idea is basically to place all the burners right behind each other in the closed-loop corresponding to the annular combustor and have the inlets coming and the burnt gases getting out from the side walls. Technically, the challenge is to design the flow properly so that this principle can run effectively on the whole operation range without failure. First, this article reviews the advantages of this technology versus conventional. The flow dynamics are entertained by the elevated momentum flux at the inlets. The effect of the heat conservativeness of the hot core on the lean combustion robustness is rated regarding the lean blowout limits. The hote core heat conservativeness connects to the permanent circulation of constantly renewed burnt gases. Another benefit is the recursive reburning effect that improves the NOx performance. Second, a combustor design is presented and detailed. The CFD study and the experiments done using this design are discussed. Third, the adequacy of additive manufacturing, and the vision of an all integrated combustor that sums up all functions between the last compressor stage and the first turbine stage are discussed. This approach can save substantially weight and congestion, which is of interest for airborne applications.
- 1 January 2023
- Published by European Turbomachinery Society
Open AccessRecursive sequential combustion using a discrete sector approach
Recursive sequential combustion is a novel concept developed by CBOne that maximises the interaction of circulated burnt gases with the reactants in the combustor of a gas turbine to improve combustion performance. The idea is basically to place all the burners right behind each other in the closed-loop corresponding to the annular combustor and have the inlets coming and the burnt gases getting out from the side walls. Technically, the challenge is to design the flow properly so that this principle can run effectively on the whole operation range without failure. First, this article reviews the advantages of this technology versus conventional. The flow dynamics are entertained by the elevated momentum flux at the inlets. The effect of the heat conservativeness of the hot core on the lean combustion robustness is rated regarding the lean blowout limits. The hote core heat conservativeness connects to the permanent circulation of constantly renewed burnt gases. Another benefit is the recursive reburning effect that improves the NOx performance. Second, a combustor design is presented and detailed. The CFD study and the experiments done using this design are discussed. Third, the adequacy of additive manufacturing, and the vision of an all integrated combustor that sums up all functions between the last compressor stage and the first turbine stage are discussed. This approach can save substantially weight and congestion, which is of interest for airborne applications.
- Open Access
- 16 July 2021
- Published by ASME International
Progress on Combined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of efficiency, environment, safety, operation flexibility and operation costs. Combustion Bay One and FH JOANNEUM initiated the project “emootion” (Engine health MOnitOring and refined combusTION control based on optical diagnostic
- 16 July 2021
- Published by ASME International
Open AccessProgress on Combined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of efficiency, environment, safety, operation flexibility and operation costs. Combustion Bay One and FH JOANNEUM initiated the project “emootion” (Engine health MOnitOring and refined combusTION control based on optical diagnostic
- Open Access
- 16 July 2021
- Published by ASME International
Progress on Forcing Pulsations for Acoustic, Thermoacoustic or Flow Control Purpose in a Pressurised Vessel by Means of a Siren
A siren is a robust fast-valve that generates effective flow pulsations and powerful noise levels under combustor field conditions. Its principle relies on a sonic air-jet sheared periodically by a cogged wheel rotating at a given speed. It is used as an alternative to loudspeakers in combustion laboratories when the use of these is made difficult because of aggressive flow
- 16 July 2021
- Published by ASME International
Open AccessProgress on Forcing Pulsations for Acoustic, Thermoacoustic or Flow Control Purpose in a Pressurised Vessel by Means of a Siren
A siren is a robust fast-valve that generates effective flow pulsations and powerful noise levels under combustor field conditions. Its principle relies on a sonic air-jet sheared periodically by a cogged wheel rotating at a given speed. It is used as an alternative to loudspeakers in combustion laboratories when the use of these is made difficult because of aggressive flow
- Open Access
- 29 June 2021
- Published by PHM Society in Phm Society European Conference
- Vol. 6 (1) , 11
Lean Blowout Sensing and Processing via Optical Interferometry and Wavelet Analysis of Dynamic Pressure Data
This paper introduces a novel approach to monitor combustion instabilities in turbomachinery. This innovation is motivated by the need to better analyze flame health in a continuous flow machine, and more precisely in its hot core expressed by machine OEMs and end-users. This improved monitoring system will support an optimization of the machine performance, leading to a safer, cleaner, more flexible and more cost-efficient operation for the end-user. There have been several numerical studies that simulate the nonlinear dynamics of flame instabilities limit in simple combustors, they predict the pressure oscillations frequency is very low 5-25 Hz. Nowadays, in gas turbine monitoring, dynamic pressure measurement sensors are based on electrical working principle technologies such as piezoelectric, piezo-resistive and capacitive measurement. While exposed to high temperatures, due to pyro-electric effects and noise spectral density of charge amplifiers, piezo sensors signal to noise ratio (SNR) decreases sharply at low frequencies (about a factor 10 every 100°). Optical sensing systems provide much better stability, in the low frequency range when exposed to high temperature and, moreover, are intrinsically insensitive to vibration or EMI perturbation. This feature allows analyzing more accurately low frequency flame dynamics. Within the frame of a joint study between Meggitt, Combustion Bay One e.U. and FH Joanneum GmbH, the behavior of an optical measurement system was tested under different combustion instability conditions. By acting on system parameters (equivalent ratio, air speed) several tests have been conducted where combustion has been driven to different instability conditions such as premixed to diffusion flame transition, lean blow out, flashback. Data have been recorded and analysed from both the optical and the piezo sensors installed within the combustion chamber. The objective of the test campaign is twofold: compare optical to piezo system performances under flame combustion instabilities and, taking advantage of improved low frequency SNR of pressure data coming from optical sensors, to develop and validate an algorithmic strategy to detect/prognose phenomena such as Lean Blow Out and Flashback. The paper initially describes the principia of the used optical sensing technology, including some relevant hardware and software aspects of the measurement chain. After that, the experimental set-up and tests conditions are presented. About piezo to optical data comparison, SNR analysis of test data confirms the expectations of a lower noise at low frequency and the improved visibility of flame instabilities provided by optical sensor. Based on this, in order to analyze the transient behavior at low frequencies associated to flame instabilities two algorithmic strategies have been developed: wavelet analysis and chaos dimension analysis. Based on these methodologies several Lean Blow Out indicators have been implemented and tested. Details of their behavior in response to the variation of the equivalence ratio close to the flame blow out are presented and discussed. Three of the proposed indicators, under the investigated test conditions, proved to possess the capability to detect the blow out event. Depending on how the approach to the blow out event occurs, some indicators also shown prognostics capability. Results show some indicators start reacting as the flame approaches to extinction or as the equivalence ratio reduces. These indicators can be considered flame health meters. The test campaign results shown in the paper allow to conclude that optical sensing technologies provide advantages over piezoelectric sensing technologies such as: insensitivity to pyro-electric effects and inherent insensitivity to external perturbations, i.e. electromagnetic interferences and radio frequency interferences, vibrations. Particularly the improved accuracy at low frequencies of the sensor coupled with new signal processing techniques, as the ones presented, may support a flame health monitoring capability and the ability to sense blowout precursors. The replacement of piezo-electric with fiber optic sensors will therefore be desirable for many combustion monitoring applications, especially the ones requiring monitoring of low frequencies. This can, provide significant payoffs in engine reliability and operability, in enabling optimal performance over extended time periods as an engine ages, in reducing maintenance costs, and in increasing engine life.
- 29 June 2021
- Published by PHM Society in Phm Society European Conference
- Vol. 6 (1) , 11
Open AccessLean Blowout Sensing and Processing via Optical Interferometry and Wavelet Analysis of Dynamic Pressure Data
This paper introduces a novel approach to monitor combustion instabilities in turbomachinery. This innovation is motivated by the need to better analyze flame health in a continuous flow machine, and more precisely in its hot core expressed by machine OEMs and end-users. This improved monitoring system will support an optimization of the machine performance, leading to a safer, cleaner, more flexible and more cost-efficient operation for the end-user. There have been several numerical studies that simulate the nonlinear dynamics of flame instabilities limit in simple combustors, they predict the pressure oscillations frequency is very low 5-25 Hz. Nowadays, in gas turbine monitoring, dynamic pressure measurement sensors are based on electrical working principle technologies such as piezoelectric, piezo-resistive and capacitive measurement. While exposed to high temperatures, due to pyro-electric effects and noise spectral density of charge amplifiers, piezo sensors signal to noise ratio (SNR) decreases sharply at low frequencies (about a factor 10 every 100°). Optical sensing systems provide much better stability, in the low frequency range when exposed to high temperature and, moreover, are intrinsically insensitive to vibration or EMI perturbation. This feature allows analyzing more accurately low frequency flame dynamics. Within the frame of a joint study between Meggitt, Combustion Bay One e.U. and FH Joanneum GmbH, the behavior of an optical measurement system was tested under different combustion instability conditions. By acting on system parameters (equivalent ratio, air speed) several tests have been conducted where combustion has been driven to different instability conditions such as premixed to diffusion flame transition, lean blow out, flashback. Data have been recorded and analysed from both the optical and the piezo sensors installed within the combustion chamber. The objective of the test campaign is twofold: compare optical to piezo system performances under flame combustion instabilities and, taking advantage of improved low frequency SNR of pressure data coming from optical sensors, to develop and validate an algorithmic strategy to detect/prognose phenomena such as Lean Blow Out and Flashback. The paper initially describes the principia of the used optical sensing technology, including some relevant hardware and software aspects of the measurement chain. After that, the experimental set-up and tests conditions are presented. About piezo to optical data comparison, SNR analysis of test data confirms the expectations of a lower noise at low frequency and the improved visibility of flame instabilities provided by optical sensor. Based on this, in order to analyze the transient behavior at low frequencies associated to flame instabilities two algorithmic strategies have been developed: wavelet analysis and chaos dimension analysis. Based on these methodologies several Lean Blow Out indicators have been implemented and tested. Details of their behavior in response to the variation of the equivalence ratio close to the flame blow out are presented and discussed. Three of the proposed indicators, under the investigated test conditions, proved to possess the capability to detect the blow out event. Depending on how the approach to the blow out event occurs, some indicators also shown prognostics capability. Results show some indicators start reacting as the flame approaches to extinction or as the equivalence ratio reduces. These indicators can be considered flame health meters. The test campaign results shown in the paper allow to conclude that optical sensing technologies provide advantages over piezoelectric sensing technologies such as: insensitivity to pyro-electric effects and inherent insensitivity to external perturbations, i.e. electromagnetic interferences and radio frequency interferences, vibrations. Particularly the improved accuracy at low frequencies of the sensor coupled with new signal processing techniques, as the ones presented, may support a flame health monitoring capability and the ability to sense blowout precursors. The replacement of piezo-electric with fiber optic sensors will therefore be desirable for many combustion monitoring applications, especially the ones requiring monitoring of low frequencies. This can, provide significant payoffs in engine reliability and operability, in enabling optimal performance over extended time periods as an engine ages, in reducing maintenance costs, and in increasing engine life.
- 21 September 2020
- Published by ASME International
Progress on Combined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of safety, environment, efficiency, operation flexibility and operation costs. This paper reports on a concept for gas turbine combustion monitoring using multiple probes that combine optical and acoustical measurements. The motivation of the project is twofold. On the one side, one wants to exploit the radiative feature of the flame and transform it into a piece of reliable information about the combustion status. On the other side, this information can be useful in terms of data interpretation or data reconciliation with other information coming from further sensors such as temperature probes, fast pressure probes or accelerometers. For this purpose, a set of multiple Rayleigh Criterion Probes (RCPs) combining optical and acoustical sensors is used. Detailed information about the RCP can be found in paper GT2017-63626, [1]. The focus is put on the detection of the flame, on the monitoring of the ignition process, on the quality assessment of combustion based on its spectral contents (including soot formation) and on the detection of possible combustion instabilities. The novel test rig used for validation of this advanced combustion monitoring concept is introduced, and minimal instrumentation including three probes is recommended. The split in red, green and blue (RGB) light components and their further analysis allows mapping the different types of operation. Solutions are proposed to bring the optical interface as near as possible to the flame and make it operational and reliable despite prevailing heat. The paper closes with a description of the ongoing tests on a pressurized combustion facility, and a sketch for a 3-RCPs based compact combustion monitoring system. The advantages of selected chromatic spectral bands are discussed, as well as the remaining challenges towards a full demonstration.
- 21 September 2020
- Published by ASME International
Progress on Combined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of safety, environment, efficiency, operation flexibility and operation costs. This paper reports on a concept for gas turbine combustion monitoring using multiple probes that combine optical and acoustical measurements. The motivation of the project is twofold. On the one side, one wants to exploit the radiative feature of the flame and transform it into a piece of reliable information about the combustion status. On the other side, this information can be useful in terms of data interpretation or data reconciliation with other information coming from further sensors such as temperature probes, fast pressure probes or accelerometers. For this purpose, a set of multiple Rayleigh Criterion Probes (RCPs) combining optical and acoustical sensors is used. Detailed information about the RCP can be found in paper GT2017-63626, [1]. The focus is put on the detection of the flame, on the monitoring of the ignition process, on the quality assessment of combustion based on its spectral contents (including soot formation) and on the detection of possible combustion instabilities. The novel test rig used for validation of this advanced combustion monitoring concept is introduced, and minimal instrumentation including three probes is recommended. The split in red, green and blue (RGB) light components and their further analysis allows mapping the different types of operation. Solutions are proposed to bring the optical interface as near as possible to the flame and make it operational and reliable despite prevailing heat. The paper closes with a description of the ongoing tests on a pressurized combustion facility, and a sketch for a 3-RCPs based compact combustion monitoring system. The advantages of selected chromatic spectral bands are discussed, as well as the remaining challenges towards a full demonstration.
- Open Access
- 6 July 2020
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 5 (3) , 15
Combined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of safety, environment, efficiency, operation flexibility, and operation costs. Combustion Bay One e.U. and FH JOANNEUM GmbH initiated in 2015 an experimental research program about the feasibility and first assessments of placing optical systems near the combustor. The project’s acronym “emootion” stands for “Engine health MOnitOring and refined combusTION control based on optical diagnostic techniques embedded in the combustor”. The motivation of the project is twofold. On one side, one wants to exploit the radiative feature of the flame and to transform it into a piece of reliable information about the combustion status. On the other side, this information can be useful in terms of data interpretation or data reconciliation with other information coming from other sensors such as temperature probes, fast pressure probes, or accelerometers. The focus is put on several aspects of combustor operations: on detection of the flame, on monitoring of the ignition process, on a quality assessment of combustion based on its spectral contents (including soot formation), and on the detection of possible combustion instabilities. Promising results were obtained using photodiodes that offer an adequate trade-off between narrow-band sensitivity and signal time response. It is shown that it is convenient to combine a fast-pressure sensor with an optical sensor in a compact form; this combination has led to the so-called Rayleigh Criterion Probe (RCP). The split in red, green, and blue (RGB) light components and their further analysis allows for mapping the different types of operation. Regarding the probe packaging aspect, it is discussed that the level of light collection needed to keep an acceptable signal-to-noise ratio has been so far a restraint for the use of optical fibres. Solutions are proposed to bring the optical sensor as close as possible to the optical interface and to make it operational and reliable in prevailing heat. This contribution closes with a description of the pressure tests in a new combustion facility built for this purpose. A compact and portable combustion monitoring system including at least 3 RCPs can become an instrumentation standard within the next decade.
- 6 July 2020
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 5 (3) , 15
Open AccessCombined Optic-Acoustic Monitoring of Combustion in a Gas Turbine
The need for better combustion monitoring in gas turbines has become more acute with the latest technical requirements, standards, and policies in terms of safety, environment, efficiency, operation flexibility, and operation costs. Combustion Bay One e.U. and FH JOANNEUM GmbH initiated in 2015 an experimental research program about the feasibility and first assessments of placing optical systems near the combustor. The project’s acronym “emootion” stands for “Engine health MOnitOring and refined combusTION control based on optical diagnostic techniques embedded in the combustor”. The motivation of the project is twofold. On one side, one wants to exploit the radiative feature of the flame and to transform it into a piece of reliable information about the combustion status. On the other side, this information can be useful in terms of data interpretation or data reconciliation with other information coming from other sensors such as temperature probes, fast pressure probes, or accelerometers. The focus is put on several aspects of combustor operations: on detection of the flame, on monitoring of the ignition process, on a quality assessment of combustion based on its spectral contents (including soot formation), and on the detection of possible combustion instabilities. Promising results were obtained using photodiodes that offer an adequate trade-off between narrow-band sensitivity and signal time response. It is shown that it is convenient to combine a fast-pressure sensor with an optical sensor in a compact form; this combination has led to the so-called Rayleigh Criterion Probe (RCP). The split in red, green, and blue (RGB) light components and their further analysis allows for mapping the different types of operation. Regarding the probe packaging aspect, it is discussed that the level of light collection needed to keep an acceptable signal-to-noise ratio has been so far a restraint for the use of optical fibres. Solutions are proposed to bring the optical sensor as close as possible to the optical interface and to make it operational and reliable in prevailing heat. This contribution closes with a description of the pressure tests in a new combustion facility built for this purpose. A compact and portable combustion monitoring system including at least 3 RCPs can become an instrumentation standard within the next decade.
- Open Access
- 13 May 2020
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 5 (2) , 9
Forcing Pulsations by Means of a Siren for Gas Turbine Applications
A siren is a robust fast-valve that generates effective flow pulsations and powerful noise levels under well-controlled conditions. It operates under the inlet flow conditions of a gas turbine combustor. Its principle is based on a sonic air jet periodically sheared by a cogged wheel rotating at a given speed. It is used as an alternative to loudspeakers in combustion laboratories when the use of these is made difficult by aggressive flow conditions, such as hot air under pressure, possibly containing impurities. It is also a serious candidate as an effective flow actuator to be deployed on power gas turbine fleets. The authors have gathered more than twenty years of knowledge on siren technology. This pulsator was originally developed for research on thermoacoustics. By scanning through a given frequency range, one detects the acoustic resonance of specific parts of the combustor assembly, or possibly triggers a combustion instability during a sensitivity analysis of a flame to small perturbations. In 2010, Giuliani et al. developed a novel siren model with the capacity to vary the amplitude of pulsation independently from the frequency. In this contribution, the physics, the metrics, and the resulting parameters of the pulsator are discussed. Technical solutions are unveiled about visiting large frequency ranges (currently 6 kHz) and achieving elevated pressure fluctuations (150 dB SPL proven, possibly up to 155 dB SPL) with a compact device. A multimodal excitation is available with this technology, one idea being to dissipate the acoustic energy on nearby peaks. The contribution ends with a summary of the applications performed so far and the perspective of an industrial application.
- 13 May 2020
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 5 (2) , 9
Open AccessForcing Pulsations by Means of a Siren for Gas Turbine Applications
A siren is a robust fast-valve that generates effective flow pulsations and powerful noise levels under well-controlled conditions. It operates under the inlet flow conditions of a gas turbine combustor. Its principle is based on a sonic air jet periodically sheared by a cogged wheel rotating at a given speed. It is used as an alternative to loudspeakers in combustion laboratories when the use of these is made difficult by aggressive flow conditions, such as hot air under pressure, possibly containing impurities. It is also a serious candidate as an effective flow actuator to be deployed on power gas turbine fleets. The authors have gathered more than twenty years of knowledge on siren technology. This pulsator was originally developed for research on thermoacoustics. By scanning through a given frequency range, one detects the acoustic resonance of specific parts of the combustor assembly, or possibly triggers a combustion instability during a sensitivity analysis of a flame to small perturbations. In 2010, Giuliani et al. developed a novel siren model with the capacity to vary the amplitude of pulsation independently from the frequency. In this contribution, the physics, the metrics, and the resulting parameters of the pulsator are discussed. Technical solutions are unveiled about visiting large frequency ranges (currently 6 kHz) and achieving elevated pressure fluctuations (150 dB SPL proven, possibly up to 155 dB SPL) with a compact device. A multimodal excitation is available with this technology, one idea being to dissipate the acoustic energy on nearby peaks. The contribution ends with a summary of the applications performed so far and the perspective of an industrial application.
- 11 June 2018
- Published by ASME International
An Assessment on the Benefits of Additive Manufacturing Regarding New Swirler Geometries for Gas Turbine Burners
In the near future, combustion engineers will shape the burner according to the flame, and not the opposite way anymore. In this contribution, this idea is explored with the help of additive manufacturing (AM). The focus is put on the design and the production of swirlers using advanced materials with the least possible efforts in terms of manufacturing. The material chosen for this study is Inconel 718. There are three motivations to this project. The first one is to design new shapes and assess these in comparison to conventional ones. The second motivation is to be able to manufacture them using additive manufacturing, and to gather know-how on selective laser melting. The third motivation is to elaborate a methodology involving engineering, research and education to promote — only if and when this is desirable — the production of series of premium parts such as high-end components of gas turbine combustor using AM. First-of-a-kind swirler shapes are explained and designed. These are unlikely to be produced using conventional manufacturing. They are then successfully produced in Inconel 718 using AM. The raw parts are directly submitted for testing with no surface post-processing. The paper states why at current state-of-the-art the raw surface quality still needs improvement, and highlights the benefits of the new swirler shape versus conventional.
- 11 June 2018
- Published by ASME International
An Assessment on the Benefits of Additive Manufacturing Regarding New Swirler Geometries for Gas Turbine Burners
In the near future, combustion engineers will shape the burner according to the flame, and not the opposite way anymore. In this contribution, this idea is explored with the help of additive manufacturing (AM). The focus is put on the design and the production of swirlers using advanced materials with the least possible efforts in terms of manufacturing. The material chosen for this study is Inconel 718. There are three motivations to this project. The first one is to design new shapes and assess these in comparison to conventional ones. The second motivation is to be able to manufacture them using additive manufacturing, and to gather know-how on selective laser melting. The third motivation is to elaborate a methodology involving engineering, research and education to promote — only if and when this is desirable — the production of series of premium parts such as high-end components of gas turbine combustor using AM. First-of-a-kind swirler shapes are explained and designed. These are unlikely to be produced using conventional manufacturing. They are then successfully produced in Inconel 718 using AM. The raw parts are directly submitted for testing with no surface post-processing. The paper states why at current state-of-the-art the raw surface quality still needs improvement, and highlights the benefits of the new swirler shape versus conventional.
- 26 June 2017
- Published by ASME International
Improvement of Impaired Combustion Conditions at Some Off-Design Operation by Driving a Precisely Controlled Modulation of the Burner Air Feed
A non-conventional method based on forced-flow combustion oscillations is investigated regarding the improvement of combustion conditions at suboptimal operating conditions. In the field of gas turbines, uncontrolled combustion oscillations are called combustion instabilities and they have been extensively studied over the last two decades. Low NOx systems that operate in the lean combustion domain are prone to enable combustion instabilities. A common way to investigate combustion instabilities is to reproduce these with help of an acoustic driver, e.g. using a loudspeaker or a fast valve in order to drive forced-flow combustion oscillations. When the oscillations match with one of the natural resonant frequencies of the combustor cavities or of the feeding pipes, the thermoacoustic coupling can occur in a well-controlled way. Some positive effects of this type of forcing can be found in the literature. In a similar context, it was shown in a previous work (GT2015-42377) under which conditions and by how far a forced-flow thermoacoustic drive can further push the lean-blow-out limits in the lean region. Following to this work, it is described that driving a resonant flame can also be beneficial regarding combustion quality. Better combustion performances were observed with the help of pulsating the burner air feed at part-load conditions on a premixed swirling flame, where combustion quality is known to be impaired at steady-state. The presented technology can then be seen as a flexible On-Off thermoacoustic drive, based on forced pulse combustion and using a siren tunable in frequency and amplitude in a refined way. The benefits and the challenges about its hypothetic implementation in the field of turbomachinery conclude this paper.
- 26 June 2017
- Published by ASME International
Improvement of Impaired Combustion Conditions at Some Off-Design Operation by Driving a Precisely Controlled Modulation of the Burner Air Feed
A non-conventional method based on forced-flow combustion oscillations is investigated regarding the improvement of combustion conditions at suboptimal operating conditions. In the field of gas turbines, uncontrolled combustion oscillations are called combustion instabilities and they have been extensively studied over the last two decades. Low NOx systems that operate in the lean combustion domain are prone to enable combustion instabilities. A common way to investigate combustion instabilities is to reproduce these with help of an acoustic driver, e.g. using a loudspeaker or a fast valve in order to drive forced-flow combustion oscillations. When the oscillations match with one of the natural resonant frequencies of the combustor cavities or of the feeding pipes, the thermoacoustic coupling can occur in a well-controlled way. Some positive effects of this type of forcing can be found in the literature. In a similar context, it was shown in a previous work (GT2015-42377) under which conditions and by how far a forced-flow thermoacoustic drive can further push the lean-blow-out limits in the lean region. Following to this work, it is described that driving a resonant flame can also be beneficial regarding combustion quality. Better combustion performances were observed with the help of pulsating the burner air feed at part-load conditions on a premixed swirling flame, where combustion quality is known to be impaired at steady-state. The presented technology can then be seen as a flexible On-Off thermoacoustic drive, based on forced pulse combustion and using a siren tunable in frequency and amplitude in a refined way. The benefits and the challenges about its hypothetic implementation in the field of turbomachinery conclude this paper.