Juha Huuki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juha Huuki has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Iñigo Flores Ituarte
Tampere University
2 shared publications - Mika Salmi
Aalto University
2 shared publications - A-.P. Pokka
University of Oulu, Materials and Mechanical Engineering, P.O. Box 4200, 90014 Oulu, Finland
1 shared publication - Antti Kaijalainen
University of Oulu
1 shared publication - Björn Hemming
Centre for Metrology and Accreditation, Tekniikantie 1, FIN-02150 Espoo, Finland
1 shared publication - E. Fangnon
Aalto University, Department of Mechanical Engineering, Puumiehenkuja 3, 02150 Espoo, Finland
1 shared publication
Latest Publications
- Open Access
- 15 September 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 44, 350-357
Effect of surface characteristics on strain distribution in air- bending
This study is a continuation of previous studies; therefore, the idea is to determine the influence of surface roughness and hardness on the bendability of a UHSS grade, and it is investigated with 3-point bending tests, utilizing Digital Image Correlation (DIC) for measuring the strain distributions on the outer curvature. Investigated bending samples of a 4 mm thick commercial bainitic-martensitic steel sheet were tested in different surface conditions: (1) as- rolled, (2) dry electropolished, (3) ultrasonic burnishing and (4) a combination of dry electropolishing and ultrasonic burnishing. Ultrasonic burnishing increased the surface hardness and decreased the surface roughness. Bending results showed that smoother surface did not lead to improved bending angles and higher hardness in the subsurface decreased the bending capacity, i.e., reduced the maximum bending angle and critical strain.
- 15 September 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 44, 350-357
Open AccessEffect of surface characteristics on strain distribution in air- bending
This study is a continuation of previous studies; therefore, the idea is to determine the influence of surface roughness and hardness on the bendability of a UHSS grade, and it is investigated with 3-point bending tests, utilizing Digital Image Correlation (DIC) for measuring the strain distributions on the outer curvature. Investigated bending samples of a 4 mm thick commercial bainitic-martensitic steel sheet were tested in different surface conditions: (1) as- rolled, (2) dry electropolished, (3) ultrasonic burnishing and (4) a combination of dry electropolishing and ultrasonic burnishing. Ultrasonic burnishing increased the surface hardness and decreased the surface roughness. Bending results showed that smoother surface did not lead to improved bending angles and higher hardness in the subsurface decreased the bending capacity, i.e., reduced the maximum bending angle and critical strain.
- Open Access
- 19 April 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 28, 1775-1780
Effects of ultrasonic burnishing on the surface quality of corrosion-resistant tool steel using a hard-carbon-coated burnishing tool
Effects of ultrasonic burnishing on the surface quality of corrosion-resistant tool steel using a hard-carbon-coated burnishing tool HUUKI Juha, ULLAH Rizwa
- 19 April 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 28, 1775-1780
Open AccessEffects of ultrasonic burnishing on the surface quality of corrosion-resistant tool steel using a hard-carbon-coated burnishing tool
Effects of ultrasonic burnishing on the surface quality of corrosion-resistant tool steel using a hard-carbon-coated burnishing tool HUUKI Juha, ULLAH Rizwa
- Open Access
- 13 October 2022
- Published by Springer Nature
- p. 38-47
Effect of Ultrasonic Burnishing Parameters on Burnished-Surface Quality of Stainless Steel After Heat Treatment
Ultrasonic burnishing induces beneficial compressive stresses and high surface quality in components with contact as a functional requirement. It was observed in previous work that some burnishing parameters can hinder burnishability of stainless steels. In this research tangential misalignment angles (TMA) for burnishing were varied considering as-supplied and heat-treated stainless steel. Properties such as surface hardness and surface roughness were measured after burnishing process. Electron Backscatter Diffraction was performed to characterize microstructure using Matlab (MTEX) to calculate average grain areas. By changing burnishing parameters, i.e., shaft rotational speed and burnishing tool diameter, it was observed that burnishing was less successful. Nevertheless, significant improvement in burnished surface quality was observed after heat-treatment process. In addition, grain size characterization revealed mean grain area reduction from 26 µm2 for unburnished to 11 µm2 and 3 µm2 for burnished and heat-treated samples respectively. Most importantly this work reveals the enhanced possibility of burnishing stainless steels after heat-treatment with varying tangential misalignment angles.
- 13 October 2022
- Published by Springer Nature
- p. 38-47
Open AccessEffect of Ultrasonic Burnishing Parameters on Burnished-Surface Quality of Stainless Steel After Heat Treatment
Ultrasonic burnishing induces beneficial compressive stresses and high surface quality in components with contact as a functional requirement. It was observed in previous work that some burnishing parameters can hinder burnishability of stainless steels. In this research tangential misalignment angles (TMA) for burnishing were varied considering as-supplied and heat-treated stainless steel. Properties such as surface hardness and surface roughness were measured after burnishing process. Electron Backscatter Diffraction was performed to characterize microstructure using Matlab (MTEX) to calculate average grain areas. By changing burnishing parameters, i.e., shaft rotational speed and burnishing tool diameter, it was observed that burnishing was less successful. Nevertheless, significant improvement in burnished surface quality was observed after heat-treatment process. In addition, grain size characterization revealed mean grain area reduction from 26 µm2 for unburnished to 11 µm2 and 3 µm2 for burnished and heat-treated samples respectively. Most importantly this work reveals the enhanced possibility of burnishing stainless steels after heat-treatment with varying tangential misalignment angles.
- 14 May 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 142 (7) , 1-38
Surface Modification of Additively Manufactured 18% Nickel Maraging Steel by Ultrasonic Vibration-Assisted Ball Burnishing
The scope of this research is to characterize and optimize the vibration-assisted ball burnishing of additively manufactured 18% Nickel Maraging steel for tooling applications. We evaluate the suitability of vibration-assisted ball burnishing as an alternative method to post-process additively manufactured tool steel. To do so, we assessed a single pass post-processing technique to enhance surface roughness, surface micro-hardness, and residual stress state. Results show that ultrasonic burnishing after age hardening functionalizes additively manufactured surfaces for tooling applications creating a beneficial compressive residual stress state on the surface. The surface micro-hardness (HV1) varied between 503 and 630 HV1, and the average surface roughness (Ra) varied between 1.31 and 0.14 µm, depending on process parameters with a maximum productivity rate of 41.66 cm2/min making it an alternative approach to functionalize additively manufactured tool components.
- 14 May 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 142 (7) , 1-38
Surface Modification of Additively Manufactured 18% Nickel Maraging Steel by Ultrasonic Vibration-Assisted Ball Burnishing
The scope of this research is to characterize and optimize the vibration-assisted ball burnishing of additively manufactured 18% Nickel Maraging steel for tooling applications. We evaluate the suitability of vibration-assisted ball burnishing as an alternative method to post-process additively manufactured tool steel. To do so, we assessed a single pass post-processing technique to enhance surface roughness, surface micro-hardness, and residual stress state. Results show that ultrasonic burnishing after age hardening functionalizes additively manufactured surfaces for tooling applications creating a beneficial compressive residual stress state on the surface. The surface micro-hardness (HV1) varied between 503 and 630 HV1, and the average surface roughness (Ra) varied between 1.31 and 0.14 µm, depending on process parameters with a maximum productivity rate of 41.66 cm2/min making it an alternative approach to functionalize additively manufactured tool components.
- 29 March 2017
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 2 (1-2) , 31-41
The ultrasonic burnishing of cobalt-chrome and stainless steel surface made by additive manufacturing
- 29 March 2017
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 2 (1-2) , 31-41
The ultrasonic burnishing of cobalt-chrome and stainless steel surface made by additive manufacturing
- Open Access
- 12 November 2014
- Published by Hindawi Limited in Journal of Engineering
- Vol. 2014, 1-8
Influence of Ultrasonic Burnishing Technique on Surface Quality and Change in the Dimensions of Metal Shafts
This paper presents ultrasonic burnishing as a mechanical surface treatment for improving the quality of rotating shafts. Ultrasonic burnishing is a modern method for finishing workpieces to produce a good surface quality. This process improves the surface quality and increases the surface hardness of the workpiece, and the surface roughness of the workpiece improves. As a result, wear resistance and fatigue life increase. Furthermore, these improvements are achieved without expensive equipment or long processing times. In this paper the influence of the ultraburnishing technique on the change in diameter and its effects on the out-of-roundness of rotating shafts are investigated. This paper also takes a look at the magnitudes of the improvement of the surface roughness as a result of using ultrasonic burnishing. Three different materials, aluminium, 34-CrNiMo6 tempering steel, and S355J2 structural steel, are examined. The results showed that ultrasonic burnishing is a treatment that improves the quality of components. Ultrasonic burnishing also has a reducing effect on the final diameter and out-of-roundness and increases the hardness of the workpiece. It can also be stated that the material of the workpiece does not have a significant effect on the magnitude of the reduced surface roughness values.
- 12 November 2014
- Published by Hindawi Limited in Journal of Engineering
- Vol. 2014, 1-8
Open AccessInfluence of Ultrasonic Burnishing Technique on Surface Quality and Change in the Dimensions of Metal Shafts
This paper presents ultrasonic burnishing as a mechanical surface treatment for improving the quality of rotating shafts. Ultrasonic burnishing is a modern method for finishing workpieces to produce a good surface quality. This process improves the surface quality and increases the surface hardness of the workpiece, and the surface roughness of the workpiece improves. As a result, wear resistance and fatigue life increase. Furthermore, these improvements are achieved without expensive equipment or long processing times. In this paper the influence of the ultraburnishing technique on the change in diameter and its effects on the out-of-roundness of rotating shafts are investigated. This paper also takes a look at the magnitudes of the improvement of the surface roughness as a result of using ultrasonic burnishing. Three different materials, aluminium, 34-CrNiMo6 tempering steel, and S355J2 structural steel, are examined. The results showed that ultrasonic burnishing is a treatment that improves the quality of components. Ultrasonic burnishing also has a reducing effect on the final diameter and out-of-roundness and increases the hardness of the workpiece. It can also be stated that the material of the workpiece does not have a significant effect on the magnitude of the reduced surface roughness values.
- 23 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (1) , 45-53
Integrity of surfaces finished with ultrasonic burnishing
Ultrasonic burnishing is a relatively new method used for finishing workpieces to produce good surface quality. Ultrasonic burnishing does not involve material removal from the surface of the workpiece. However, the method has a significant deforming effect on the material, especially close to the surface, which is why it is vital to know the effect of the method to residual stresses in the material. This study looks at the residual stresses produced in two 34CrNiMo6-M tempering steel qualities of different hardness. The magnitude of stresses is examined using the hole drilling method. The hardness and surface quality of the finished workpiece are measured. The results show that the ultrasonic burnishing not only treats material on the surface efficiently but also deforms the material deeper, producing compressive residual stresses in the workpiece. The hardness increases after finishing and surface quality improves significantly. The roundness of the workpiece is improved and dimensional changes are minor.
- 23 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (1) , 45-53
Integrity of surfaces finished with ultrasonic burnishing
Ultrasonic burnishing is a relatively new method used for finishing workpieces to produce good surface quality. Ultrasonic burnishing does not involve material removal from the surface of the workpiece. However, the method has a significant deforming effect on the material, especially close to the surface, which is why it is vital to know the effect of the method to residual stresses in the material. This study looks at the residual stresses produced in two 34CrNiMo6-M tempering steel qualities of different hardness. The magnitude of stresses is examined using the hole drilling method. The hardness and surface quality of the finished workpiece are measured. The results show that the ultrasonic burnishing not only treats material on the surface efficiently but also deforms the material deeper, producing compressive residual stresses in the workpiece. The hardness increases after finishing and surface quality improves significantly. The roundness of the workpiece is improved and dimensional changes are minor.