James G. Mantovani
Research Subjects
Research Interests
James G. Mantovani has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Robert P. Mueller
Swamp Works Laboratory, NASA Kennedy Space Center (KSC), Mail Stop: UB-R1, Kennedy Space Center, FL 32899
5 shared publications - Ivan I. Townsend
Swamp Works Laboratory, Craig Technologies, Inc., Kennedy Space Center, FL 32899
4 shared publications - Philip T. Metzger
Hawking Center for Microgravity Research and Education University of Central Florida 32828 Orlando FL USA
3 shared publications - John E. Lane
ASRC Aerospace
2 shared publications - Laurent Sibille
Ascentech Enterprises Inc. serving Swamp Works Laboratory, NASA KSC, FL 32899
2 shared publications - A. D. S. Olson
Fusion Technology Institute, Dept. of Engineering Physics, Univ. of Wisconsin-Madison, 1500 Engineering Dr., Madison, WI 53706
1 shared publication
Latest Publications
- Open Access
The Damage to Lunar Orbiting Spacecraft Caused by the Ejecta of Lunar Landers
This manuscript analyzes lunar lander soil erosion models and trajectory models to calculate how much damage will occur to spacecraft orbiting in the vicinity of the Moon. The soil erosion models have considerable uncertainty due to gaps in our understanding of the basic physics. The results for ~40 t landers show that the Lunar Orbital Gateway will be impacted by 1000s to 10,000s of particles per square meter but the particle sizes are very small and the impact velocity is low so the damage will be slight. However, a spacecraft in Low Lunar Orbit that happens to pass through the ejecta sheet will sustain extensive damage with hundreds of millions of impacts per square meter: although they are small, they are in the hypervelocity regime, and exposed glass on the spacecraft will sustain spallation over 4% of its surface.
Open AccessThe Damage to Lunar Orbiting Spacecraft Caused by the Ejecta of Lunar Landers
This manuscript analyzes lunar lander soil erosion models and trajectory models to calculate how much damage will occur to spacecraft orbiting in the vicinity of the Moon. The soil erosion models have considerable uncertainty due to gaps in our understanding of the basic physics. The results for ~40 t landers show that the Lunar Orbital Gateway will be impacted by 1000s to 10,000s of particles per square meter but the particle sizes are very small and the impact velocity is low so the damage will be slight. However, a spacecraft in Low Lunar Orbit that happens to pass through the ejecta sheet will sustain extensive damage with hundreds of millions of impacts per square meter: although they are small, they are in the hypervelocity regime, and exposed glass on the spacecraft will sustain spallation over 4% of its surface.
- 21 September 2022
- Published by Morressier GmbH
Modeling of Lunar Dust Particle Trajectories for Rocket Plume-Surface Impingement Studies
Building on previous work performed at NASA Kennedy Space Center in the Granular Mechanics and Regolith Operations Laboratory (GMRO Lab) a decade |
- 21 September 2022
- Published by Morressier GmbH
Modeling of Lunar Dust Particle Trajectories for Rocket Plume-Surface Impingement Studies
Building on previous work performed at NASA Kennedy Space Center in the Granular Mechanics and Regolith Operations Laboratory (GMRO Lab) a decade |
- 21 September 2022
- Published by Morressier GmbH
Simulant and Environment Requirements for Space Resources Technology Development
The use of space resources will be necessary for extraplanetary colonization and extended exploration. The most immediately practical uses of spa |
- 21 September 2022
- Published by Morressier GmbH
Simulant and Environment Requirements for Space Resources Technology Development
The use of space resources will be necessary for extraplanetary colonization and extended exploration. The most immediately practical uses of spa |
- 21 September 2022
- Published by Morressier GmbH
Damage to Lunar Orbiting Spacecraft Caused by the Ejecta of Lunar Landers
This manuscript analyzes lunar lander soil erosion models and trajectory models to calculate how much damage will occur to spacecraft orbiting in |
- 21 September 2022
- Published by Morressier GmbH
Damage to Lunar Orbiting Spacecraft Caused by the Ejecta of Lunar Landers
This manuscript analyzes lunar lander soil erosion models and trajectory models to calculate how much damage will occur to spacecraft orbiting in |
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 960-971
Launch Pad in a Box
This paper describes a deployable launch system capability being developed at NASA KSC that was publicly announced in May 2015. It is a set of multi-user ground support equipment that will be used to test and launch small class launch vehicles. The paper also describes a transportable modular launch/landing pad concept that was developed to support vertical takeoff vertical landing vehicles, such as the NASA JSC Morpheus Lander, and discusses rocket plume effects on launch/landing pad surfaces.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 960-971
Launch Pad in a Box
This paper describes a deployable launch system capability being developed at NASA KSC that was publicly announced in May 2015. It is a set of multi-user ground support equipment that will be used to test and launch small class launch vehicles. The paper also describes a transportable modular launch/landing pad concept that was developed to support vertical takeoff vertical landing vehicles, such as the NASA JSC Morpheus Lander, and discusses rocket plume effects on launch/landing pad surfaces.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 202-212
Modeling Dynamics of Counter-Rotating Bucket Drum Excavation for In Situ Resource Utilization (ISRU) in Low-Gravity Environments
In situ resource utilization (ISRU) will be a critical, game-changing technology needed for the enabling of long-term manned missions to Mars. In order for these missions to remain sustainable, critical resources must be obtainable in sufficient quantities from the regolith of Mars to sustain the technological and human needs of the mission. These goals are addressed in this simulation study by using a computational simulation of the most current design iteration of regolith advanced surface systems operations robot (RASSOR), an excavator for Mars regolith that uses counter-rotating bucket drum design for use in low-gravity environments. In this simulation, the following is performed: (1) the dynamics of the excavation and traction forces are modeled using the Bekker equations for traction and the Balovnev equations for bucket excavation, and (2) this simulation data is compared to empirical tests of draw-bar pull tests (for traction) and bucket drum rotation tests (for excavation) of test hardware in BP-1 regolith simulant.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 202-212
Modeling Dynamics of Counter-Rotating Bucket Drum Excavation for In Situ Resource Utilization (ISRU) in Low-Gravity Environments
In situ resource utilization (ISRU) will be a critical, game-changing technology needed for the enabling of long-term manned missions to Mars. In order for these missions to remain sustainable, critical resources must be obtainable in sufficient quantities from the regolith of Mars to sustain the technological and human needs of the mission. These goals are addressed in this simulation study by using a computational simulation of the most current design iteration of regolith advanced surface systems operations robot (RASSOR), an excavator for Mars regolith that uses counter-rotating bucket drum design for use in low-gravity environments. In this simulation, the following is performed: (1) the dynamics of the excavation and traction forces are modeled using the Bekker equations for traction and the Balovnev equations for bucket excavation, and (2) this simulation data is compared to empirical tests of draw-bar pull tests (for traction) and bucket drum rotation tests (for excavation) of test hardware in BP-1 regolith simulant.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 391-401
Helium Implantation into JSC-1A Lunar Regolith Simulant for Testing Volatile Extraction Technologies
Research is ongoing to develop a laboratory volatiles extraction system that can demonstrate a heating process for releasing helium-3 (3He) and other important lunar volatiles from lunar regolith. Beyond the Apollo and Luna lunar soil samples, there is no regolith or regolith simulant implanted with solar wind volatiles that is available. An implantation device is being developed to implant helium into batches of JSC-1A simulant. The device, named the solar wind implanter (SWIM), uses a voltage difference between planar electrodes to accelerate ions at solar-wind speeds into a thin, falling sheet of regolith simulant. The SWIM device has been assembled and initial implantation tests have been conducted. Updates to the system are being developed to allow SWIM to produce simulant with the desired amount of embedded helium.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 391-401
Helium Implantation into JSC-1A Lunar Regolith Simulant for Testing Volatile Extraction Technologies
Research is ongoing to develop a laboratory volatiles extraction system that can demonstrate a heating process for releasing helium-3 (3He) and other important lunar volatiles from lunar regolith. Beyond the Apollo and Luna lunar soil samples, there is no regolith or regolith simulant implanted with solar wind volatiles that is available. An implantation device is being developed to implant helium into batches of JSC-1A simulant. The device, named the solar wind implanter (SWIM), uses a voltage difference between planar electrodes to accelerate ions at solar-wind speeds into a thin, falling sheet of regolith simulant. The SWIM device has been assembled and initial implantation tests have been conducted. Updates to the system are being developed to allow SWIM to produce simulant with the desired amount of embedded helium.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 36-47
Optical Extinction Measurements of Dust Density in the GMRO Regolith Test Bin
A regolith simulant test bin was constructed and completed in the Granular Mechanics and Regolith Operations (GMRO) Lab in 2013. This planetary regolith test bed (PRTB) is a 64 m2 × 1 m deep test bin housed in a climate-controlled facility and contains 120 MT of lunar-regolith simulant, called Black Point-1 or BP-1, from Black Point, AZ. One of the current uses of the test bin is to study the effects of difficult lighting and dust conditions on telerobotic perception systems to better assess and refine regolith operations for asteroid, Mars, and polar lunar missions. Low illumination and low angle of incidence lighting pose significant problems to computer vision and human perception. Levitated dust on asteroids interferes with imaging and degrades depth perception. Dust storms on Mars pose a significant problem. Due to these factors, the likely performance of telerobotics is poorly understood for future missions. Current space telerobotic systems are only operated in bright lighting and dust-free conditions. This technology development testing will identify: (1) the impact of degraded lighting and environmental dust on computer vision and operator perception, (2) potential methods and procedures for mitigating these impacts, (3) requirements for telerobotic perception systems for asteroid capture, Mars dust storms, and lunar regolith ISRU missions.
- 12 January 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 36-47
Optical Extinction Measurements of Dust Density in the GMRO Regolith Test Bin
A regolith simulant test bin was constructed and completed in the Granular Mechanics and Regolith Operations (GMRO) Lab in 2013. This planetary regolith test bed (PRTB) is a 64 m2 × 1 m deep test bin housed in a climate-controlled facility and contains 120 MT of lunar-regolith simulant, called Black Point-1 or BP-1, from Black Point, AZ. One of the current uses of the test bin is to study the effects of difficult lighting and dust conditions on telerobotic perception systems to better assess and refine regolith operations for asteroid, Mars, and polar lunar missions. Low illumination and low angle of incidence lighting pose significant problems to computer vision and human perception. Levitated dust on asteroids interferes with imaging and degrades depth perception. Dust storms on Mars pose a significant problem. Due to these factors, the likely performance of telerobotics is poorly understood for future missions. Current space telerobotic systems are only operated in bright lighting and dust-free conditions. This technology development testing will identify: (1) the impact of degraded lighting and environmental dust on computer vision and operator perception, (2) potential methods and procedures for mitigating these impacts, (3) requirements for telerobotic perception systems for asteroid capture, Mars dust storms, and lunar regolith ISRU missions.
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 26 (1) , 169-175
Planetary Regolith Delivery Systems for ISRU
This paper describes tests conducted since 2008 at the National Aeronautics and Space Administration (NASA) Kennedy Space Center (KSC) to address engineering challenges associated with delivering planetary regolith to in situ resource utilization (ISRU) systems. The need to excavate regolith under reduced-gravity conditions on a planetary surface and then deliver it to systems for material analysis and/or processing constrains the possible engineering approaches that can be used in space. Mission costs may further limit the mass and available power of a regolith delivery system. Mechanical systems operating in a planetary environment require high reliability with respect to system service life because it is usually difficult or impossible to perform maintenance robotically on a planetary surface. The regolith delivery system for most ISRU systems must have a leak-tight interface between the near-vacuum found on a planetary surface and the pressurized atmosphere within the ISRU reactor. Depending o...
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 26 (1) , 169-175
Planetary Regolith Delivery Systems for ISRU
This paper describes tests conducted since 2008 at the National Aeronautics and Space Administration (NASA) Kennedy Space Center (KSC) to address engineering challenges associated with delivering planetary regolith to in situ resource utilization (ISRU) systems. The need to excavate regolith under reduced-gravity conditions on a planetary surface and then deliver it to systems for material analysis and/or processing constrains the possible engineering approaches that can be used in space. Mission costs may further limit the mass and available power of a regolith delivery system. Mechanical systems operating in a planetary environment require high reliability with respect to system service life because it is usually difficult or impossible to perform maintenance robotically on a planetary surface. The regolith delivery system for most ISRU systems must have a leak-tight interface between the near-vacuum found on a planetary surface and the pressurized atmosphere within the ISRU reactor. Depending o...
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 26 (1) , 18-29
Affordable, Rapid Bootstrapping of the Space Industry and Solar System Civilization
Advances in robotics and additive manufacturing have become game-changing for the prospects of space industry. It has become feasible to bootstrap a self-sustaining, self-expanding industry at reasonably low cost. Simple modeling was developed to identify the main parameters of successful bootstrapping. This indicates that bootstrapping can be achieved with as little as 12 t landed on the Moon during a period of about 20 years. The equipment will be teleoperated and then transitioned to full autonomy so the industry can spread to the asteroid belt and beyond. The strategy begins with a subreplicating system and evolves toward full self-sustainability (full closure) via an in situ technology spiral. The industry grows exponentially because of the free real estate, energy, and material resources of space. The mass of industrial assets at the end of bootstrapping will be 156 t with 60 humanoid robots or as high as 40,000 t with as many as 100,000 humanoid robots if faster manufacturing is supported b...
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 26 (1) , 18-29
Affordable, Rapid Bootstrapping of the Space Industry and Solar System Civilization
Advances in robotics and additive manufacturing have become game-changing for the prospects of space industry. It has become feasible to bootstrap a self-sustaining, self-expanding industry at reasonably low cost. Simple modeling was developed to identify the main parameters of successful bootstrapping. This indicates that bootstrapping can be achieved with as little as 12 t landed on the Moon during a period of about 20 years. The equipment will be teleoperated and then transitioned to full autonomy so the industry can spread to the asteroid belt and beyond. The strategy begins with a subreplicating system and evolves toward full self-sustainability (full closure) via an in situ technology spiral. The industry grows exponentially because of the free real estate, energy, and material resources of space. The mass of industrial assets at the end of bootstrapping will be 156 t with 60 humanoid robots or as high as 40,000 t with as many as 100,000 humanoid robots if faster manufacturing is supported b...