Chiaki Sato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chiaki Sato has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Yu Sekiguchi
Laboratory for Future Interdisciplinary Research of Science and Technology, Institute of Integrated Research, Institute of Science Tokyo, Yokohama 226-8501, Japan
14 shared publications - Kazumasa Shimamoto
Research Institute of Core Technology for Materials Innovation, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba 305-8565, Japan
5 shared publications - Haruhisa Akiyama
Adhesion and Interface Technology Research Group, Research Institute of Core Technology for Materials Innovation, The National Institute of Advanced Industrial Science and Technology, 1-2-1, Namiki, Tsukuba 305-8564, Ibaraki, Japan
3 shared publications - Jin-Woo Han
Department of Mechanical Engineering, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa 226-8501, Japan
3 shared publications Kazumasa Shimamoto
Nanomaterials Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565, Japan
3 shared publications- Keiji Houjou
Innovative Structural Materials Association, The National Institute of Advanced Industrial Science and Technology, Tsukuba, Japan
3 shared publications
Latest Publications
- Open Access
- 26 August 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 152
Techniques to suppress the lift-off peel of films at the edge of an adherend based on the energy release rate
- 26 August 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 152
Open AccessTechniques to suppress the lift-off peel of films at the edge of an adherend based on the energy release rate
- Open Access
Fracture Energy Reduction Caused by Water at the Crack Front of an Aluminum/Epoxy Resin Interface
A detailed understanding of interface degradation in humid environments is essential for improving the reliability of adhesive bonding technologies. Water absorption within the adhesive layer significantly affects joint strength, a factor considered to be long-term degradation. However, even if water does not approach the interface from the inside due to absorption, it can reach the interface from the outside through the crack tip and instantaneously affect the fracture behavior of the interface, highlighting the need to investigate short-term degradation mechanisms. In this study, the effect of water at the aluminum/epoxy resin interface on crack propagation was quantitatively evaluated by measuring the mode I energy release rate through double cantilever beam (DCB) tests. By changing the surface condition of the adherend, interfacial and cohesive failures were achieved, and DCB tests were conducted in air and underwater conditions to compare the effect of water on the fracture energy. Results showed that the interfacial fracture energy decreased by more than 50% when the crack propagated in water, but no significant reduction was observed in the cohesive fracture energy. The decrease in interfacial fracture energy in the presence of water indicates the immediate disruption of chemical bonding.
Open AccessFracture Energy Reduction Caused by Water at the Crack Front of an Aluminum/Epoxy Resin Interface
A detailed understanding of interface degradation in humid environments is essential for improving the reliability of adhesive bonding technologies. Water absorption within the adhesive layer significantly affects joint strength, a factor considered to be long-term degradation. However, even if water does not approach the interface from the inside due to absorption, it can reach the interface from the outside through the crack tip and instantaneously affect the fracture behavior of the interface, highlighting the need to investigate short-term degradation mechanisms. In this study, the effect of water at the aluminum/epoxy resin interface on crack propagation was quantitatively evaluated by measuring the mode I energy release rate through double cantilever beam (DCB) tests. By changing the surface condition of the adherend, interfacial and cohesive failures were achieved, and DCB tests were conducted in air and underwater conditions to compare the effect of water on the fracture energy. Results showed that the interfacial fracture energy decreased by more than 50% when the crack propagated in water, but no significant reduction was observed in the cohesive fracture energy. The decrease in interfacial fracture energy in the presence of water indicates the immediate disruption of chemical bonding.
- 27 January 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142 (11-12) , 5863-5877
Transfer decoration technique on glass curved in three-axis direction: Selective placement of decoration layers by reverse prediction
- 27 January 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142 (11-12) , 5863-5877
Transfer decoration technique on glass curved in three-axis direction: Selective placement of decoration layers by reverse prediction
- Open Access
- 28 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (40) , 54610-54626
Direct Measurement of the Diffusion Coefficient of Adhesives from Moisture Distribution in Adhesive Layers Using Near-Infrared Spectroscopy
In this study, we used near-infrared spectroscopy to measure the moisture penetration in epoxy adhesives and investigated the difference in the diffusion coefficients between the bulk and the adhesive layer. Moisture diffusion was evaluated under 100% RH and water immersion conditions. First, the effects of the curing agents and additives on moisture diffusion in the bulk were gravimetrically evaluated using epoxy-coated quartz glass plates. Different diffusion behaviors were observed depending on the curing agent used. The presence of additives resulted in higher diffusion coefficients, whereas the overall moisture content was low. Next, the moisture distribution in the adhesive layer was visualized using a specimen sandwiched between the quartz glass plates, and the diffusion coefficient of the adhesive layer was calculated. The diffusion coefficient in the adhesive layer was larger than that in the bulk. For adhesives cured with hydrophobic diamine, the diffusion coefficient within the adhesive layer increased by approximately 1.5 times compared with that in the bulk, regardless of the exposure environment. The adhesive, composed of a resin, Dicyandiamide, and additives, showed a 2-fold increase in the diffusion coefficient under high-humidity exposure conditions but no significant change under the water immersion condition. Therefore, these results suggest that, for an accurate analysis of moisture distribution, it is important to measure the diffusion coefficient of the adhesive layer directly rather than using the diffusion coefficient of the material itself.
- 28 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (40) , 54610-54626
Open AccessDirect Measurement of the Diffusion Coefficient of Adhesives from Moisture Distribution in Adhesive Layers Using Near-Infrared Spectroscopy
In this study, we used near-infrared spectroscopy to measure the moisture penetration in epoxy adhesives and investigated the difference in the diffusion coefficients between the bulk and the adhesive layer. Moisture diffusion was evaluated under 100% RH and water immersion conditions. First, the effects of the curing agents and additives on moisture diffusion in the bulk were gravimetrically evaluated using epoxy-coated quartz glass plates. Different diffusion behaviors were observed depending on the curing agent used. The presence of additives resulted in higher diffusion coefficients, whereas the overall moisture content was low. Next, the moisture distribution in the adhesive layer was visualized using a specimen sandwiched between the quartz glass plates, and the diffusion coefficient of the adhesive layer was calculated. The diffusion coefficient in the adhesive layer was larger than that in the bulk. For adhesives cured with hydrophobic diamine, the diffusion coefficient within the adhesive layer increased by approximately 1.5 times compared with that in the bulk, regardless of the exposure environment. The adhesive, composed of a resin, Dicyandiamide, and additives, showed a 2-fold increase in the diffusion coefficient under high-humidity exposure conditions but no significant change under the water immersion condition. Therefore, these results suggest that, for an accurate analysis of moisture distribution, it is important to measure the diffusion coefficient of the adhesive layer directly rather than using the diffusion coefficient of the material itself.
- Open Access
- 15 August 2024
- Published by Japan Institute of Light Metals in Journal of Japan Institute of Light Metals
- Vol. 74 (8) , 324-326
Recent trends in adhesive bonding for aluminum structures
- 15 August 2024
- Published by Japan Institute of Light Metals in Journal of Japan Institute of Light Metals
- Vol. 74 (8) , 324-326
Open AccessRecent trends in adhesive bonding for aluminum structures
- Open Access
- 15 August 2024
- Published by Japan Institute of Light Metals in Journal of Japan Institute of Light Metals
- Vol. 74 (8) , 336-339
Effect of surface treatment of aluminum adherends on capacitance and strength of adhesively bonded joints
Effect of surface treatment of aluminum
- 15 August 2024
- Published by Japan Institute of Light Metals in Journal of Japan Institute of Light Metals
- Vol. 74 (8) , 336-339
Open AccessEffect of surface treatment of aluminum adherends on capacitance and strength of adhesively bonded joints
Effect of surface treatment of aluminum
- Open Access
- 20 July 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 134
Experimental investigation of moisture penetration in adhesive layers under varying bonding conditions using near-infrared spectroscopy
- 20 July 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 134
Open AccessExperimental investigation of moisture penetration in adhesive layers under varying bonding conditions using near-infrared spectroscopy
- Open Access
Analytical Calculation of Relationship Temperature and Fatigue and Creep Strength Based on Thermal Activation
The purpose of this study was to formulate a mathematical expression for the temperature dependence of adhesive strength using various parameters. Adhesive structures are typically exposed to a broad temperature range, spanning from low to high temperatures; therefore, understanding how their strength depends on temperature is crucial. The strength was measured through tensile, fatigue, and creep tests at temperatures ranging from −60 °C to 135 °C. The properties of these test types were thoroughly investigated by analyzing the strength of the test results from a thermal activity perspective. The results demonstrate that there is a clear relationship between temperature and strength. The intensity decreased with temperature according to the exponential function and could be accurately represented using the parameters of thermal activity. The temperature at which the strength begins to decrease in the fatigue test was higher than in the static tests. Consequently, we were able to accurately express the relationship between the temperature and intensity using certain parameters. Few studies successfully developed a precise nonlinear relationship between temperature and intensity using approximate expressions.
Open AccessAnalytical Calculation of Relationship Temperature and Fatigue and Creep Strength Based on Thermal Activation
The purpose of this study was to formulate a mathematical expression for the temperature dependence of adhesive strength using various parameters. Adhesive structures are typically exposed to a broad temperature range, spanning from low to high temperatures; therefore, understanding how their strength depends on temperature is crucial. The strength was measured through tensile, fatigue, and creep tests at temperatures ranging from −60 °C to 135 °C. The properties of these test types were thoroughly investigated by analyzing the strength of the test results from a thermal activity perspective. The results demonstrate that there is a clear relationship between temperature and strength. The intensity decreased with temperature according to the exponential function and could be accurately represented using the parameters of thermal activity. The temperature at which the strength begins to decrease in the fatigue test was higher than in the static tests. Consequently, we were able to accurately express the relationship between the temperature and intensity using certain parameters. Few studies successfully developed a precise nonlinear relationship between temperature and intensity using approximate expressions.
- Open Access
Multi-Objective Optimization of Adhesive Joint Strength and Elastic Modulus of Adhesive Epoxy with Active Learning
Studying multiple properties of a material concurrently is essential for obtaining a comprehensive understanding of its behavior and performance. However, this approach presents certain challenges. For instance, simultaneous examination of various properties often necessitates extensive experimental resources, thereby increasing the overall cost and time required for research. Furthermore, the pursuit of desirable properties for one application may conflict with those needed for another, leading to trade-off scenarios. In this study, we focused on investigating adhesive joint strength and elastic modulus, both crucial properties directly impacting adhesive behavior. To determine elastic modulus, we employed a non-destructive indentation method for converting hardness measurements. Additionally, we introduced a specimen apparatus preparation method to ensure the fabrication of smooth surfaces and homogeneous polymeric specimens, free from voids and bubbles. Our experiments utilized a commercially available bisphenol A-based epoxy resin in combination with a Poly(propylene glycol) curing agent. We generated an initial dataset comprising experimental results from 32 conditions, which served as input for training a machine learning model. Subsequently, we used this model to predict outcomes for a total of 256 conditions. To address the high deviation in prediction results, we implemented active learning approaches, achieving a 50% reduction in deviation while maintaining model accuracy. Through our analysis, we observed a trade-off boundary (Pareto frontier line) between adhesive joint strength and elastic modulus. Leveraging Bayesian optimization, we successfully identified experimental conditions that surpassed this boundary, yielding an adhesive joint strength of 25.2 MPa and an elastic modulus of 182.5 MPa.
Open AccessMulti-Objective Optimization of Adhesive Joint Strength and Elastic Modulus of Adhesive Epoxy with Active Learning
Studying multiple properties of a material concurrently is essential for obtaining a comprehensive understanding of its behavior and performance. However, this approach presents certain challenges. For instance, simultaneous examination of various properties often necessitates extensive experimental resources, thereby increasing the overall cost and time required for research. Furthermore, the pursuit of desirable properties for one application may conflict with those needed for another, leading to trade-off scenarios. In this study, we focused on investigating adhesive joint strength and elastic modulus, both crucial properties directly impacting adhesive behavior. To determine elastic modulus, we employed a non-destructive indentation method for converting hardness measurements. Additionally, we introduced a specimen apparatus preparation method to ensure the fabrication of smooth surfaces and homogeneous polymeric specimens, free from voids and bubbles. Our experiments utilized a commercially available bisphenol A-based epoxy resin in combination with a Poly(propylene glycol) curing agent. We generated an initial dataset comprising experimental results from 32 conditions, which served as input for training a machine learning model. Subsequently, we used this model to predict outcomes for a total of 256 conditions. To address the high deviation in prediction results, we implemented active learning approaches, achieving a 50% reduction in deviation while maintaining model accuracy. Through our analysis, we observed a trade-off boundary (Pareto frontier line) between adhesive joint strength and elastic modulus. Leveraging Bayesian optimization, we successfully identified experimental conditions that surpassed this boundary, yielding an adhesive joint strength of 25.2 MPa and an elastic modulus of 182.5 MPa.