Yu Sekiguchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yu Sekiguchi has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
Chiaki Sato
33 shared publications- Chiaki Sato
Laboratory for Future Interdisciplinary Research of Science and Technology, Institute of Integrated Research, Institute of Science Tokyo, Yokohama 226-8501, Japan
14 shared publications Kazumasa Shimamoto
11 shared publications- Kazumasa Shimamoto
Research Institute of Core Technology for Materials Innovation, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba 305-8565, Japan
7 shared publications C. Sato
5 shared publications- Jin-Woo Han
Department of Mechanical Engineering, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa 226-8501, Japan
5 shared publications
Latest Publications
- Open Access
- 26 August 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 152
Techniques to suppress the lift-off peel of films at the edge of an adherend based on the energy release rate
- 26 August 2026
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 152
Open AccessTechniques to suppress the lift-off peel of films at the edge of an adherend based on the energy release rate
- Open Access
- 6 May 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 342
Self-loading loop tack test for measuring the critical energy release rate of weakly adhesive films
- 6 May 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 342
Open AccessSelf-loading loop tack test for measuring the critical energy release rate of weakly adhesive films
- Open Access
Fracture Energy Reduction Caused by Water at the Crack Front of an Aluminum/Epoxy Resin Interface
A detailed understanding of interface degradation in humid environments is essential for improving the reliability of adhesive bonding technologies. Water absorption within the adhesive layer significantly affects joint strength, a factor considered to be long-term degradation. However, even if water does not approach the interface from the inside due to absorption, it can reach the interface from the outside through the crack tip and instantaneously affect the fracture behavior of the interface, highlighting the need to investigate short-term degradation mechanisms. In this study, the effect of water at the aluminum/epoxy resin interface on crack propagation was quantitatively evaluated by measuring the mode I energy release rate through double cantilever beam (DCB) tests. By changing the surface condition of the adherend, interfacial and cohesive failures were achieved, and DCB tests were conducted in air and underwater conditions to compare the effect of water on the fracture energy. Results showed that the interfacial fracture energy decreased by more than 50% when the crack propagated in water, but no significant reduction was observed in the cohesive fracture energy. The decrease in interfacial fracture energy in the presence of water indicates the immediate disruption of chemical bonding.
Open AccessFracture Energy Reduction Caused by Water at the Crack Front of an Aluminum/Epoxy Resin Interface
A detailed understanding of interface degradation in humid environments is essential for improving the reliability of adhesive bonding technologies. Water absorption within the adhesive layer significantly affects joint strength, a factor considered to be long-term degradation. However, even if water does not approach the interface from the inside due to absorption, it can reach the interface from the outside through the crack tip and instantaneously affect the fracture behavior of the interface, highlighting the need to investigate short-term degradation mechanisms. In this study, the effect of water at the aluminum/epoxy resin interface on crack propagation was quantitatively evaluated by measuring the mode I energy release rate through double cantilever beam (DCB) tests. By changing the surface condition of the adherend, interfacial and cohesive failures were achieved, and DCB tests were conducted in air and underwater conditions to compare the effect of water on the fracture energy. Results showed that the interfacial fracture energy decreased by more than 50% when the crack propagated in water, but no significant reduction was observed in the cohesive fracture energy. The decrease in interfacial fracture energy in the presence of water indicates the immediate disruption of chemical bonding.
- Open Access
- 3 May 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 140
Fatigue crack growth analysis of a ductile structural acrylic adhesive under constant-amplitude load control at various loading conditions
- 3 May 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 140
Open AccessFatigue crack growth analysis of a ductile structural acrylic adhesive under constant-amplitude load control at various loading conditions
- Open Access
- 13 February 2025
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (12) , 1422-1449
Three-point bending strength of double-hat beams of high strength steel bonded adhesively
- 13 February 2025
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (12) , 1422-1449
Open AccessThree-point bending strength of double-hat beams of high strength steel bonded adhesively
- Open Access
- 13 January 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 209
A modified spectral collocation method for vibration of sandwich beams based on a higher-order layer-wise beam theory
- 13 January 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 209
Open AccessA modified spectral collocation method for vibration of sandwich beams based on a higher-order layer-wise beam theory
- Open Access
- 24 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Effect of rapid interfacial moisture penetration on moisture distribution within adhesive layers
- 24 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Open AccessEffect of rapid interfacial moisture penetration on moisture distribution within adhesive layers
- Open Access
- 18 November 2024
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (9) , 1143-1162
Fracture Energy Determination of Wedge-opening Double Cantilever Beam Tests
- 18 November 2024
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (9) , 1143-1162
Open AccessFracture Energy Determination of Wedge-opening Double Cantilever Beam Tests
- Open Access
- 28 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (40) , 54610-54626
Direct Measurement of the Diffusion Coefficient of Adhesives from Moisture Distribution in Adhesive Layers Using Near-Infrared Spectroscopy
In this study, we used near-infrared spectroscopy to measure the moisture penetration in epoxy adhesives and investigated the difference in the diffusion coefficients between the bulk and the adhesive layer. Moisture diffusion was evaluated under 100% RH and water immersion conditions. First, the effects of the curing agents and additives on moisture diffusion in the bulk were gravimetrically evaluated using epoxy-coated quartz glass plates. Different diffusion behaviors were observed depending on the curing agent used. The presence of additives resulted in higher diffusion coefficients, whereas the overall moisture content was low. Next, the moisture distribution in the adhesive layer was visualized using a specimen sandwiched between the quartz glass plates, and the diffusion coefficient of the adhesive layer was calculated. The diffusion coefficient in the adhesive layer was larger than that in the bulk. For adhesives cured with hydrophobic diamine, the diffusion coefficient within the adhesive layer increased by approximately 1.5 times compared with that in the bulk, regardless of the exposure environment. The adhesive, composed of a resin, Dicyandiamide, and additives, showed a 2-fold increase in the diffusion coefficient under high-humidity exposure conditions but no significant change under the water immersion condition. Therefore, these results suggest that, for an accurate analysis of moisture distribution, it is important to measure the diffusion coefficient of the adhesive layer directly rather than using the diffusion coefficient of the material itself.
- 28 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (40) , 54610-54626
Open AccessDirect Measurement of the Diffusion Coefficient of Adhesives from Moisture Distribution in Adhesive Layers Using Near-Infrared Spectroscopy
In this study, we used near-infrared spectroscopy to measure the moisture penetration in epoxy adhesives and investigated the difference in the diffusion coefficients between the bulk and the adhesive layer. Moisture diffusion was evaluated under 100% RH and water immersion conditions. First, the effects of the curing agents and additives on moisture diffusion in the bulk were gravimetrically evaluated using epoxy-coated quartz glass plates. Different diffusion behaviors were observed depending on the curing agent used. The presence of additives resulted in higher diffusion coefficients, whereas the overall moisture content was low. Next, the moisture distribution in the adhesive layer was visualized using a specimen sandwiched between the quartz glass plates, and the diffusion coefficient of the adhesive layer was calculated. The diffusion coefficient in the adhesive layer was larger than that in the bulk. For adhesives cured with hydrophobic diamine, the diffusion coefficient within the adhesive layer increased by approximately 1.5 times compared with that in the bulk, regardless of the exposure environment. The adhesive, composed of a resin, Dicyandiamide, and additives, showed a 2-fold increase in the diffusion coefficient under high-humidity exposure conditions but no significant change under the water immersion condition. Therefore, these results suggest that, for an accurate analysis of moisture distribution, it is important to measure the diffusion coefficient of the adhesive layer directly rather than using the diffusion coefficient of the material itself.
- Open Access
- 20 July 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 134
Experimental investigation of moisture penetration in adhesive layers under varying bonding conditions using near-infrared spectroscopy
- 20 July 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 134
Open AccessExperimental investigation of moisture penetration in adhesive layers under varying bonding conditions using near-infrared spectroscopy