Shahid Akhtar
Shahid Akhtar has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ragnhild Elizabeth Aune
Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), 7491 Trondheim, Norway
6 shared publications - Massoud Hassanabadi
Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), 7491 Trondheim, Norway
3 shared publications - Artur Kudyba
Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz Vei 2, 7034 Trondheim, Norway
2 shared publications - Inge Johansen
Hydro Aluminum, Romsdalsvegen 1, 6600 Sunndalsøra, Norway
2 shared publications - Jafar Safarian
Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz Vei 2, 7491 Trondheim, Norway
2 shared publications - Mark William Kennedy
Norwegian University of Science and Technology (NTNU)
2 shared publications
Latest Publications
- 3 February 2024
- Published by Springer Nature
- p. 941-951
Optimization of Boron Treatment for Production of 1370 Electrically Conductive Grade Aluminum Alloy
- 3 February 2024
- Published by Springer Nature
- p. 941-951
Optimization of Boron Treatment for Production of 1370 Electrically Conductive Grade Aluminum Alloy
- Open Access
Study and Modelling of Fluid Flow in Ceramic Foam Filters
To investigate the fluid flow characteristics of conventional Ceramic Foam Filters (CFFs) of grades 30 and 50, a 2D macro-scale geometry was generated by converting pixel grid images of the filters into vector format images. The flow behaviour through the filter channels was then numerically modelled using the Stocks equation within the Creeping Flow interface of COMSOL Multiphysics®. Through modelling, the average interstitial velocity was estimated and found to be higher than the corresponding value obtained from the Dupuit–Forchheimer equation. The discrepancy obtained suggested that the flow behaviour within the filter channels differed from that based on the simplified assumptions of the equation. The porosity and permeability of the CFFs were evaluated during the post-processing stage using surface integration and user-defined equations. The experimentally determined porosity closely matched the values obtained from the simulation model, demonstrating the reliability of the numerical approach. However, the permeability values from the simulation of CFFs of grades 30 and 50 were higher than those obtained experimentally. This discrepancy can be attributed to the larger channels in the generated geometrical pattern compared to the original CFF structure. The present findings highlight the effectiveness of the proposed methodology in developing a representative macro-scale geometry for CFFs and in simulating fluid flow behaviour.
Open AccessStudy and Modelling of Fluid Flow in Ceramic Foam Filters
To investigate the fluid flow characteristics of conventional Ceramic Foam Filters (CFFs) of grades 30 and 50, a 2D macro-scale geometry was generated by converting pixel grid images of the filters into vector format images. The flow behaviour through the filter channels was then numerically modelled using the Stocks equation within the Creeping Flow interface of COMSOL Multiphysics®. Through modelling, the average interstitial velocity was estimated and found to be higher than the corresponding value obtained from the Dupuit–Forchheimer equation. The discrepancy obtained suggested that the flow behaviour within the filter channels differed from that based on the simplified assumptions of the equation. The porosity and permeability of the CFFs were evaluated during the post-processing stage using surface integration and user-defined equations. The experimentally determined porosity closely matched the values obtained from the simulation model, demonstrating the reliability of the numerical approach. However, the permeability values from the simulation of CFFs of grades 30 and 50 were higher than those obtained experimentally. This discrepancy can be attributed to the larger channels in the generated geometrical pattern compared to the original CFF structure. The present findings highlight the effectiveness of the proposed methodology in developing a representative macro-scale geometry for CFFs and in simulating fluid flow behaviour.
- Open Access
Hydraulic Characterization of Ceramic Foam Filters Used in Aluminum Filtration
Ceramic Foam Filters (CFF) are frequently used during the filtration of aluminum (Al) melts to produce high-quality products. In the present study, the physical and hydraulic characteristics of alumina (Al2O3)-based CFF from three different suppliers (A, B and C) have been thoroughly investigated. The filters’ porosity and pore diameter, i.e., Window and Cell Feret diameters, were measured and the permeability of the different filters calculated based on pressure drop experiments. The comparison of the classification systems of CFF, i.e., Grade and PPI (Pore Per Inch) numbers, using statistical analysis of permeability and Window Feret diameter showed significant variations between the morphological and hydraulic properties of some CFFs of identical Grade and PPI numbers. Moreover, the Fanning friction factor was plotted as a function of interstitial Reynolds numbers (Rei), and laminar, transient, and turbulent flow regimes were identified. The relationship between the Fanning friction factor and the interstitial Reynolds numbers of all the filter samples investigated was processed using regression analysis, and a model equation developed to calculate the pressure drop over the CFF using the Window Feret diameter. The correlation between the experimental pressure drop values and the derived model equation indicates that empirical expressions for calculating the pressure drop over CFFs should be derived based on experimental measurements carried out at the velocity range of the application of the CFF, which is about 10 mm·s−1 for aluminum filtration.
Open AccessHydraulic Characterization of Ceramic Foam Filters Used in Aluminum Filtration
Ceramic Foam Filters (CFF) are frequently used during the filtration of aluminum (Al) melts to produce high-quality products. In the present study, the physical and hydraulic characteristics of alumina (Al2O3)-based CFF from three different suppliers (A, B and C) have been thoroughly investigated. The filters’ porosity and pore diameter, i.e., Window and Cell Feret diameters, were measured and the permeability of the different filters calculated based on pressure drop experiments. The comparison of the classification systems of CFF, i.e., Grade and PPI (Pore Per Inch) numbers, using statistical analysis of permeability and Window Feret diameter showed significant variations between the morphological and hydraulic properties of some CFFs of identical Grade and PPI numbers. Moreover, the Fanning friction factor was plotted as a function of interstitial Reynolds numbers (Rei), and laminar, transient, and turbulent flow regimes were identified. The relationship between the Fanning friction factor and the interstitial Reynolds numbers of all the filter samples investigated was processed using regression analysis, and a model equation developed to calculate the pressure drop over the CFF using the Window Feret diameter. The correlation between the experimental pressure drop values and the derived model equation indicates that empirical expressions for calculating the pressure drop over CFFs should be derived based on experimental measurements carried out at the velocity range of the application of the CFF, which is about 10 mm·s−1 for aluminum filtration.
- Open Access
Valorization of Aluminum Dross with Copper via High Temperature Melting to Produce Al-Cu Alloys
The valorization of aluminum dross for Al recovery was performed via its mixing with metallic copper to produce Al-Cu alloys. This approach was with the intention of establishing a new smelting process to treat the dross with Cu scrap use. To evaluate the high temperature interaction of the materials, the wettability of a Cu-containing aluminum alloy with the non-metallic components of the dross was studied by the sessile drop method. It was found that the wetting was weak via temperature changes at 973–1373 K, and consequently no proper metal separation occurred. To better separate the metallic and non-metallic phases with larger density differences, a higher Cu portion was considered to obtain a significantly denser metallic phase, and it was found that partial separation of the Al in an Al-Cu alloy is possible. The complete separation of the metallic components of the dross was, however, experienced by the dross and copper melting with the addition of pre-melted calcium aluminate slags at elevated temperatures. It was found that Al-Cu alloys were produced and separated from the adjacent slags, and the aluminum oxide of the dross ended up in the slag phase. Moreover, the characteristics of the produced slags depend on the process charge.
Open AccessValorization of Aluminum Dross with Copper via High Temperature Melting to Produce Al-Cu Alloys
The valorization of aluminum dross for Al recovery was performed via its mixing with metallic copper to produce Al-Cu alloys. This approach was with the intention of establishing a new smelting process to treat the dross with Cu scrap use. To evaluate the high temperature interaction of the materials, the wettability of a Cu-containing aluminum alloy with the non-metallic components of the dross was studied by the sessile drop method. It was found that the wetting was weak via temperature changes at 973–1373 K, and consequently no proper metal separation occurred. To better separate the metallic and non-metallic phases with larger density differences, a higher Cu portion was considered to obtain a significantly denser metallic phase, and it was found that partial separation of the Al in an Al-Cu alloy is possible. The complete separation of the metallic components of the dross was, however, experienced by the dross and copper melting with the addition of pre-melted calcium aluminate slags at elevated temperatures. It was found that Al-Cu alloys were produced and separated from the adjacent slags, and the aluminum oxide of the dross ended up in the slag phase. Moreover, the characteristics of the produced slags depend on the process charge.
- Open Access
Aluminothermic Reduction of Manganese Oxide from Selected MnO-Containing Slags
The aluminothermic reduction process of manganese oxide from different slags by aluminum was investigated using pure Al and two types of industrial Al dross. Two types of MnO-containing slags were used: a synthetic highly pure CaO-MnO slag and an industrial high carbon ferromanganese slag. Mixtures of Al and slag with more Al than the stoichiometry were heated and interacted in an induction furnace up to 1873 K, yielding molten metal and slag products. The characterization of the produced metal and slag phases indicated that the complete reduction of MnO occurs via the aluminothermic process. Moreover, as the Al content in the charge was high, it also completely reduced SiO2 in the industrial ferromanganese slag. A small mass transport of Ca and Mg into the metal phase was also observed, which was shown to be affected by the slag chemistry. The obtained results indicated that the valorization of both Al dross and FeMn slag in a single process for the production of Mn, Mn-Al, and Mn-Al-Si alloys is possible. Moreover, the energy balance for the process indicated that the energy consumption of the process to produce Mn-Al alloys via the proposed process is insignificant due to the highly exothermic reactions at high temperatures.
Open AccessAluminothermic Reduction of Manganese Oxide from Selected MnO-Containing Slags
The aluminothermic reduction process of manganese oxide from different slags by aluminum was investigated using pure Al and two types of industrial Al dross. Two types of MnO-containing slags were used: a synthetic highly pure CaO-MnO slag and an industrial high carbon ferromanganese slag. Mixtures of Al and slag with more Al than the stoichiometry were heated and interacted in an induction furnace up to 1873 K, yielding molten metal and slag products. The characterization of the produced metal and slag phases indicated that the complete reduction of MnO occurs via the aluminothermic process. Moreover, as the Al content in the charge was high, it also completely reduced SiO2 in the industrial ferromanganese slag. A small mass transport of Ca and Mg into the metal phase was also observed, which was shown to be affected by the slag chemistry. The obtained results indicated that the valorization of both Al dross and FeMn slag in a single process for the production of Mn, Mn-Al, and Mn-Al-Si alloys is possible. Moreover, the energy balance for the process indicated that the energy consumption of the process to produce Mn-Al alloys via the proposed process is insignificant due to the highly exothermic reactions at high temperatures.
- Open Access
- 31 March 2020
- Published by Springer Nature in JOM
- Vol. 72 (6) , 2295-2304
Physical and Mechanical Properties of Graphene Nanoplatelet-Reinforced Al6061-T6 Composites Processed by Spark Plasma Sintering
Aluminium matrix composites with high specific strength are attracting attention for use in automobile and aerospace applications. Graphene nanoplatelets (GNPs) were added in 0.1, 0.5, and 1 weight fractions to an Al6061 matrix. Spark plasma sintering was used with a combination of solution sonication and ball milling to disperse the GNPs in the Al6061 matrix. The evolution of the microstructure was studied using optical and scanning electron microscopy. The uniformity of the GNP distribution is discussed in light of selected ball milling parameters. Electron backscattered diffraction analysis was used to measure the grain size and misorientation. X-ray diffraction analysis and transmission electron microscopy revealed neat and clean interfaces between the matrix and GNPs. Hardness and tensile testing revealed a considerable increment in the strength of the final composite after addition of GNPs. Traces of GNP clusters were found in the 1 wt.% composite as well as premature failure at lower strain due to the insufficient load transfer capability of the Al6061-T6 matrix. An illustrative two-dimensional model was developed to explain the load transfer behavior and the deterioration of the mechanical properties.
- 31 March 2020
- Published by Springer Nature in JOM
- Vol. 72 (6) , 2295-2304
Open AccessPhysical and Mechanical Properties of Graphene Nanoplatelet-Reinforced Al6061-T6 Composites Processed by Spark Plasma Sintering
Aluminium matrix composites with high specific strength are attracting attention for use in automobile and aerospace applications. Graphene nanoplatelets (GNPs) were added in 0.1, 0.5, and 1 weight fractions to an Al6061 matrix. Spark plasma sintering was used with a combination of solution sonication and ball milling to disperse the GNPs in the Al6061 matrix. The evolution of the microstructure was studied using optical and scanning electron microscopy. The uniformity of the GNP distribution is discussed in light of selected ball milling parameters. Electron backscattered diffraction analysis was used to measure the grain size and misorientation. X-ray diffraction analysis and transmission electron microscopy revealed neat and clean interfaces between the matrix and GNPs. Hardness and tensile testing revealed a considerable increment in the strength of the final composite after addition of GNPs. Traces of GNP clusters were found in the 1 wt.% composite as well as premature failure at lower strain due to the insufficient load transfer capability of the Al6061-T6 matrix. An illustrative two-dimensional model was developed to explain the load transfer behavior and the deterioration of the mechanical properties.
- 14 August 2013
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 44 (5) , 1056-1057
Reply to Discussion of “Characterization of Ceramic Foam Filters Used for Liquid Metal Filtration” and “Electromagnetically Modified Filtration of Aluminum Melts: Part I. Electromagnetic Theory and 30 PPI Ceramic Foam Filter Experimental Results”
- 14 August 2013
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 44 (5) , 1056-1057
Reply to Discussion of “Characterization of Ceramic Foam Filters Used for Liquid Metal Filtration” and “Electromagnetically Modified Filtration of Aluminum Melts: Part I. Electromagnetic Theory and 30 PPI Ceramic Foam Filter Experimental Results”
- 17 March 2012
- Published by Wiley
- p. 353-360
Heat Treatment of Black Dross for the Production of a Value Added Material-A Preliminary Study
- 17 March 2012
- Published by Wiley
- p. 353-360
Heat Treatment of Black Dross for the Production of a Value Added Material-A Preliminary Study
- 28 February 2011
- Published by Wiley
- p. 763-768
Electromagnetically Enhanced Filtration of Aluminum Melts
- 28 February 2011
- Published by Wiley
- p. 763-768
Electromagnetically Enhanced Filtration of Aluminum Melts