MWM. Jürgen Wolf

M. Jürgen Wolf

*This is an algorithmically generated author record based on publicly available information.

M. Jürgen Wolf has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Characterisation of Cu/Cu bonding using self-assembled monolayer

    by Maria Lykova, Iuliana Panchenko, Ulrich Künzelmann, Johanna Reif, Marion Geidel, M. Jürgen Wolf, Klaus-Dieter Lang

    Purpose: Cu/Cu diffusion bonding is characterised by high electrical and thermal conductivity, as well as the mechanical strength of the interconnects. But despite a number of advantages, Cu oxidises readily upon exposure to air. To break through the adsorbed oxide-layer high temperature and pressure, long bonding time and inert gas atmosphere are required during the bonding process. This paper aims to present the implementation of an organic self-assembled monolayer (SAM) as a temporary protective coating that inhibits Cu oxidation. Design/methodology/approach: Information concerning elemental composition of the Cu surface has been yielded by X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared (FTIR) spectroscopy. Two types of substrates (electroplated and sputtered Cu) are prepared for thermocompression bonding in two different ways. In the first case, Cu is cleaned with dilute sulphuric acid to remove native copper oxide. In the second case, passivation with SAM followed the cleaning step with dilute sulphuric acid. Shear strength, fracture surface, microstructure of the received Cu/Cu interconnects are investigated after the bonding procedure. Findings: The XPS method revealed that SAM can retard Cu from oxidation on air for at least 12 h. SAM passivation on the substrates with sputtered Cu appears to have better quality than on the electroplated ones. This derives from the results of the shear strength tests and scanning electron microscopy (SEM) imaging of Cu/Cu interconnects cross sections. SAM passivation improved the bonding quality of the interconnects with sputtered Cu in comparison to the cleaned samples without passivation. Originality/value: The Cu/Cu bonding procedure was optimised by a novel preparation method using SAMs which enables storage and bonding of Si-dies with Cu microbumps at air conditions while remaining a good-quality interconnect. The passivation revealed to be advantageous for the smooth surfaces. SEM and shear strength tests showed improved bonding quality for the passivated bottom dies with sputtered Cu in comparison to the samples without SAM.


  • Open Access

    Technologies for 3D Heterogeneous Integration

    by Jürgen Wolf, P. Ramm, Armin Klumpp, H. Reichl

    3D-Integration is a promising technology towards higher interconnect densities and shorter wiring lengths between multiple chip stacks, thus achieving a very high performance level combined with low power consumption. This technology also offers the possibility to build up systems with high complexity just by combining devices of different technologies. For ultra thin silicon is the base of this integration technology, the fundamental processing steps will be described, as well as appropriate handling concepts. Three main concepts for 3D integration have been developed at IZM. The approach with the greatest flexibility called Inter Chip Via - Solid Liquid Interdiffusion (ICV-SLID) is introduced. This is a chip-to-wafer stacking technology which combines the advantages of the Inter Chip Via (ICV) process and the solid-liquid-interdiffusion technique (SLID) of copper and tin. The fully modular ICV-SLID concept allows the formation of multiple device stacks. A test chip was designed and the total process sequence of the ICV-SLID technology for the realization of a three-layer chip-to-wafer stack was demonstrated. The proposed wafer-level 3D integration concept has the potential for low cost fabrication of multi-layer high-performance 3D-SoCs and is well suited as a replacement for embedded technologies based on monolithic integration. To address yield issues a wafer-level chip-scale handling is presented as well, to select known-good dies and work on them with wafer-level process sequences before joining them to integrated stacks.

  • Flexible Circuit Carrier with Integrated Passives for High Density Integration

    by Thorsten Fischer, Kai Zoschke, Katrin Scherpinski, Klaus Buschick, Oswin Ehrmann, M. Jürgen Wolf, Herbert Reichl