Jie Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jie Luo has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Larry A. Fahnestock
Univ. of Illinois Urbana-Champaign
5 shared publications - Alexander F. Vakakis
University of Illinois at Urbana-Champaign
3 shared publications - Lawrence A. Bergman
University of Illinois at Urbana–Champaign, Urbana, Illinois 61801
3 shared publications - Nicholas E. Wierschem
Graduate Research Assistant, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana-Champaign, 205 North Mathews Ave., Urbana, IL 61801
3 shared publications - Billie F. Spencer
Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801, USA
2 shared publications - Donald Michael McFarland
Ningbo Institute of Digital Twin, Eastern Institute of Technology, 568 Tongxin Road, Ningbo 315200, P. R. China
2 shared publications
Latest Publications
- 4 April 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 48-57
Seismic Response of Integral Abutment Bridges
The use of integral abutment bridges (IABs) is widespread throughout the U.S.; the Midwestern state of Illinois is no exception, with this bridge type commonly utilized in the state. The proximity of southern Illinois to the New Madrid Seismic Zone creates concerns about the earthquake-resistance of IABs in this region. Recent research concerning the seismic response of seat-type abutment bridges has determined that the failure of abutment bearings and backwalls are important fusing mechanisms under moderate to strong seismic loads. However, only limited research has been conducted on the seismic response of IABs (especially in Illinois), which do not have the abutment bearings that allow seat-type abutment bridges to behave in a quasi-isolated fashion. Through the use of site-specific ground motions developed for various locations in southern Illinois, along with a set of IAB models created in OpenSees, this paper presents preliminary data concerning the seismic structural behavior of an IAB designed per current IDOT procedures
- 4 April 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 48-57
Seismic Response of Integral Abutment Bridges
The use of integral abutment bridges (IABs) is widespread throughout the U.S.; the Midwestern state of Illinois is no exception, with this bridge type commonly utilized in the state. The proximity of southern Illinois to the New Madrid Seismic Zone creates concerns about the earthquake-resistance of IABs in this region. Recent research concerning the seismic response of seat-type abutment bridges has determined that the failure of abutment bearings and backwalls are important fusing mechanisms under moderate to strong seismic loads. However, only limited research has been conducted on the seismic response of IABs (especially in Illinois), which do not have the abutment bearings that allow seat-type abutment bridges to behave in a quasi-isolated fashion. Through the use of site-specific ground motions developed for various locations in southern Illinois, along with a set of IAB models created in OpenSees, this paper presents preliminary data concerning the seismic structural behavior of an IAB designed per current IDOT procedures
- 4 May 2016
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 13 (5) , 581-603
Seismic analysis incorporating detailed structure–abutment–foundation interaction for quasi-isolated highway bridges
The Illinois Department of Transportation has adopted an economical and pragmatic methodology for designing earthquake-resistant highway bridges in the Midwestern United States. These so-called quasi-isolated bridges employ low-cost non-seismically designed bearing components as sacrificial structural fuses. During seismic events, fusing actions of these components and subsequent sliding of superstructures on substructures are intended to achieve response characteristics similar to those of conventionally isolated bridges that employ specially designed isolators. This study explores seismic structure-abutment-foundation interaction for quasi-isolated bridges in Illinois, employing a detailed yet efficient non-linear finite-element model for seat-type bridge abutments. The abutment model incorporates many structural components and geotechnical mechanisms that are critical to seismic response of the structure-abutment-foundation (SAF) system. Through non-linear static analyses performed on a complete bridge model, the force-transfer mechanisms, component fusing performance, and potential failure modes of the SAF system were explored. Using earthquake ground motions, non-linear dynamic analyses were conducted to evaluate seismic characteristics of the quasi-isolated bridge, sequences of critical limit state occurrences, and effects of abutment attributes on bridge seismic performance. The influence of abutment model sophistication on simulated bridge response was also highlighted by direct comparison of simulation results obtained from different models.
- 4 May 2016
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 13 (5) , 581-603
Seismic analysis incorporating detailed structure–abutment–foundation interaction for quasi-isolated highway bridges
The Illinois Department of Transportation has adopted an economical and pragmatic methodology for designing earthquake-resistant highway bridges in the Midwestern United States. These so-called quasi-isolated bridges employ low-cost non-seismically designed bearing components as sacrificial structural fuses. During seismic events, fusing actions of these components and subsequent sliding of superstructures on substructures are intended to achieve response characteristics similar to those of conventionally isolated bridges that employ specially designed isolators. This study explores seismic structure-abutment-foundation interaction for quasi-isolated bridges in Illinois, employing a detailed yet efficient non-linear finite-element model for seat-type bridge abutments. The abutment model incorporates many structural components and geotechnical mechanisms that are critical to seismic response of the structure-abutment-foundation (SAF) system. Through non-linear static analyses performed on a complete bridge model, the force-transfer mechanisms, component fusing performance, and potential failure modes of the SAF system were explored. Using earthquake ground motions, non-linear dynamic analyses were conducted to evaluate seismic characteristics of the quasi-isolated bridge, sequences of critical limit state occurrences, and effects of abutment attributes on bridge seismic performance. The influence of abutment model sophistication on simulated bridge response was also highlighted by direct comparison of simulation results obtained from different models.
- 1 June 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 140 (6)
Experimental Testing and Numerical Simulation of a Six-Story Structure Incorporating Two-Degree-of-Freedom Nonlinear Energy Sink
The nonlinear energy sink (NES) is a fully passive attachment used to rapidly dissipate a significant portion of energy induced in a linear primary structure to which it is attached. In this study, the performance of a Type III NES in reducing the response of a large primary structure when subjected to a shock-type loading is evaluated experimentally. The Type III NES is a two-degree-of-freedom device comprising two relatively lightweight masses in series coupled together and to the primary structure through essentially nonlinear (i.e., nonlinearizable) stiffness elements. The essential stiffness nonlinearity of the NES and the corresponding lack of preferential resonance frequencies enable it to resonantly interact with multiple structural modes over broad frequency and energy ranges. Hence a local NES can induce global effects in the dynamics of the structure to which it is attached. In this study, and for the first time, specially shaped polyurethane bumpers are employed for realizing these essentially nonlinear stiffness elements of the Type III NES. Measures calculated from the experiments in this study, such as the effective damping of the primary structure, indicate the ability of the NES to dissipate energy and reduce the response of the primary structure over a wide range of magnitudes of a shock loading. Good agreement between numerical predictions and experimental observations validates the identified model of the NES.
- 1 June 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 140 (6)
Experimental Testing and Numerical Simulation of a Six-Story Structure Incorporating Two-Degree-of-Freedom Nonlinear Energy Sink
The nonlinear energy sink (NES) is a fully passive attachment used to rapidly dissipate a significant portion of energy induced in a linear primary structure to which it is attached. In this study, the performance of a Type III NES in reducing the response of a large primary structure when subjected to a shock-type loading is evaluated experimentally. The Type III NES is a two-degree-of-freedom device comprising two relatively lightweight masses in series coupled together and to the primary structure through essentially nonlinear (i.e., nonlinearizable) stiffness elements. The essential stiffness nonlinearity of the NES and the corresponding lack of preferential resonance frequencies enable it to resonantly interact with multiple structural modes over broad frequency and energy ranges. Hence a local NES can induce global effects in the dynamics of the structure to which it is attached. In this study, and for the first time, specially shaped polyurethane bumpers are employed for realizing these essentially nonlinear stiffness elements of the Type III NES. Measures calculated from the experiments in this study, such as the effective damping of the primary structure, indicate the ability of the NES to dissipate energy and reduce the response of the primary structure over a wide range of magnitudes of a shock loading. Good agreement between numerical predictions and experimental observations validates the identified model of the NES.
- 1 May 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 140 (5)
Realization of a Strongly Nonlinear Vibration-Mitigation Device Using Elastomeric Bumpers
Recent research has shown the viability of using nonlinear energy-sink (NES) devices for vibration mitigation in mechanical and structural systems. When attached to a primary structure, these lightweight passive devices can effectively reduce the structural vibration response through their nonlinear stiffness properties. In this research, a two-degree-of-freedom NES device is designed using innovative elastomeric bumpers as the critical components providing nonlinear restoring forces. A number of elastomeric bumper configurations are evaluated experimentally, and the effect of geometric bumper parameters is investigated with a focus on their influence on the stiffness properties of the bumper. A NES device employing different bumpers is then implemented on a 6-story model building and tested using impulse-like base motion. Nonlinear system identification of the NES device shows that nonlinear stiffness properties are achieved using the elastomeric bumpers. Shake-table testing of the building equipped with the NES device demonstrates that the device is capable of dissipating and redistributing the induced vibration energy in a rapid, effective, and robust fashion.
- 1 May 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 140 (5)
Realization of a Strongly Nonlinear Vibration-Mitigation Device Using Elastomeric Bumpers
Recent research has shown the viability of using nonlinear energy-sink (NES) devices for vibration mitigation in mechanical and structural systems. When attached to a primary structure, these lightweight passive devices can effectively reduce the structural vibration response through their nonlinear stiffness properties. In this research, a two-degree-of-freedom NES device is designed using innovative elastomeric bumpers as the critical components providing nonlinear restoring forces. A number of elastomeric bumper configurations are evaluated experimentally, and the effect of geometric bumper parameters is investigated with a focus on their influence on the stiffness properties of the bumper. A NES device employing different bumpers is then implemented on a 6-story model building and tested using impulse-like base motion. Nonlinear system identification of the NES device shows that nonlinear stiffness properties are achieved using the elastomeric bumpers. Shake-table testing of the building equipped with the NES device demonstrates that the device is capable of dissipating and redistributing the induced vibration energy in a rapid, effective, and robust fashion.
- 7 April 2014
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 43 (12) , 1829-1851
Design, simulation, and large‐scale testing of an innovative vibration mitigation device employing essentially nonlinear elastomeric springs
SUMMARY: This study proposes an innovative passive vibration mitigation device employing essentially nonlinear elastomeric springs as its most critical component. Essential nonlinearity denotes the absence (or near absence) of a linear component in the stiffness characteristics of these elastomeric springs. These devices were implemented and tested on a large‐scale nine‐story model building structure. The main focus of these devices is to mitigate structural response under impulse‐like and seismic loading when the structure remains elastic. During the design process of the device, numerical simulations, optimizations, and parametric studies of the structure‐device system were performed to obtain stiffness parameters for the devices so that they can maximize the apparent damping of the fundamental mode of the structure. Pyramidal elastomeric springs were employed to physically realize the optimized essentially nonlinear spring components. Component‐level finite element analyses and experiments were conducted to design the nonlinear springs. Finally, shake table tests using impulse‐like and seismic excitation with different loading levels were performed to experimentally evaluate the performance of the device. Experimental results demonstrate that the properly designed devices can mitigate structural vibration responses, including floor acceleration, displacement, and column strain in an effective, rapid, and robust fashion. Comparison between numerical and experimental results verified the computational model of the nonlinear system and provided a comprehensive verification for the proposed device. Copyright © 2014 John Wiley & Sons, Ltd.
- 7 April 2014
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 43 (12) , 1829-1851
Design, simulation, and large‐scale testing of an innovative vibration mitigation device employing essentially nonlinear elastomeric springs
SUMMARY: This study proposes an innovative passive vibration mitigation device employing essentially nonlinear elastomeric springs as its most critical component. Essential nonlinearity denotes the absence (or near absence) of a linear component in the stiffness characteristics of these elastomeric springs. These devices were implemented and tested on a large‐scale nine‐story model building structure. The main focus of these devices is to mitigate structural response under impulse‐like and seismic loading when the structure remains elastic. During the design process of the device, numerical simulations, optimizations, and parametric studies of the structure‐device system were performed to obtain stiffness parameters for the devices so that they can maximize the apparent damping of the fundamental mode of the structure. Pyramidal elastomeric springs were employed to physically realize the optimized essentially nonlinear spring components. Component‐level finite element analyses and experiments were conducted to design the nonlinear springs. Finally, shake table tests using impulse‐like and seismic excitation with different loading levels were performed to experimentally evaluate the performance of the device. Experimental results demonstrate that the properly designed devices can mitigate structural vibration responses, including floor acceleration, displacement, and column strain in an effective, rapid, and robust fashion. Comparison between numerical and experimental results verified the computational model of the nonlinear system and provided a comprehensive verification for the proposed device. Copyright © 2014 John Wiley & Sons, Ltd.
- 30 April 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 2241-2252
Experimental Testing of a Large 9-Story Structure Equipped with Multiple Nonlinear Energy Sinks Subjected to an Impulsive Loading
Building structures can be critically affected by impulsive loads such as blasts, collisions, gusts, and pulse-dominated earthquakes. The addition of nonlinear energy sinks (NESs) in buildings has been proposed as a means to rapidly and passively dissipate the energy in a system exposed to this type of loading. This rapid dissipation occurs because the essential nonlinearity of the NES allows it to resonate with any mode of the structure and engage in targeted energy transfer, the nearly one-way transfer of energy to the NES where it is locally dissipated. Additionally, the NES couples the modes of the structure and facilitates the transfer of energy from the lower modes of the structure to the higher modes, where it can be dissipated at a reduced time scale. In this study the experimental performance of a system of multiple NESs in a large 9-story test structure is discussed. Two different types of NESs are used, each of which employ a different type of restoring force; one type of NES utilizes a smooth restoring force that is roughly cubic, while the other utilizes a linear restoring force coupled with one-sided vibro-impacts. To load this system, an impulse-like ground motion is applied via a large shake table. The results of this study show that the system of NESs greatly improves the performance of the structure across a wide range of impulse amplitudes by reducing and very rapidly attenuating its response.
- 30 April 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 2241-2252
Experimental Testing of a Large 9-Story Structure Equipped with Multiple Nonlinear Energy Sinks Subjected to an Impulsive Loading
Building structures can be critically affected by impulsive loads such as blasts, collisions, gusts, and pulse-dominated earthquakes. The addition of nonlinear energy sinks (NESs) in buildings has been proposed as a means to rapidly and passively dissipate the energy in a system exposed to this type of loading. This rapid dissipation occurs because the essential nonlinearity of the NES allows it to resonate with any mode of the structure and engage in targeted energy transfer, the nearly one-way transfer of energy to the NES where it is locally dissipated. Additionally, the NES couples the modes of the structure and facilitates the transfer of energy from the lower modes of the structure to the higher modes, where it can be dissipated at a reduced time scale. In this study the experimental performance of a system of multiple NESs in a large 9-story test structure is discussed. Two different types of NESs are used, each of which employ a different type of restoring force; one type of NES utilizes a smooth restoring force that is roughly cubic, while the other utilizes a linear restoring force coupled with one-sided vibro-impacts. To load this system, an impulse-like ground motion is applied via a large shake table. The results of this study show that the system of NESs greatly improves the performance of the structure across a wide range of impulse amplitudes by reducing and very rapidly attenuating its response.