BJBritto Pari James

Britto Pari James

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Britto Pari James has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design of Low-Complexity and High-Speed Reconfigurable FIR Filter Using a Modified Distributed Arithmetic Structure

    by S. C. Prasanna, Britto Pari James, Dhandapani Vaithiyanathan, Jin Zhang, Man-Fai Leung

    The implementation of Software-Defined Radio (SDR) requires various reconfigurable modules. One of the important modules is the reconfigurable finite impulse response (FIR) filter, which SDR has to support different wireless standards by reconfiguring the single filter structure. The complexity of implementing these filters depends on the method of changing coefficients, which can be resolved using the coefficient decimation method. This paper presents a Distributed Arithmetic (DA)-based reconfigurable FIR filter employing the Coefficient Decimation method (CDM) to achieve a low-complexity and scalable hardware architecture for Software Defined Radio (SDR) applications. FPGA synthesis results demonstrate approximately proportional resource growth with increasing filter order, requiring 400, 950, 2200, 4680, and 9800 LUTs for the 32-, 64-, 128-, 256-, and 512-tap implementations, respectively. The design operates at maximum frequencies of 165 MHz and 150 MHz, while consuming only 145 mW and 295 mW of power for the 128-tap and 256-tap configurations, respectively, without the use of dedicated DSP blocks. In addition, the proposed architecture achieves the lowest LUT-per-tap ratio among the compared designs, highlighting its efficient utilization of FPGA resources. Overall, the results demonstrate that the proposed CDM–DA architecture provides an effective trade-off among hardware resource utilization, operating frequency, power consumption, and scalability, making it a promising solution for high-order reconfigurable FIR filters in SDR channelization, multirate signal processing, and adaptive filtering applications.

  • Open Access

    High-Efficiency Digital Filters for Spectral Parameter Approximation in SDR

    by Subahar Arivalagan, Britto Pari James, Man-Fai Leung

    Filters supporting dynamic reconfiguration that use the spectral parameter approximation (SPA) technique, together with other methodologies, and the interpolated spectral parameter approximation (ISPA) technique offer dynamic adjustment of the cutoff frequency (fc) with a narrow transition bandwidth and a very wide fc range. However, they suffer from a high multiplier requirement, leading to increased hardware resource usage. With fewer multipliers, we suggest the Multiply and Accumulate (MAC)-based SPA (MAC-SPA) and MAC-based interpolated SPA (MAC-ISPA) filter in this article. This article describes a unified MAC structure utilizing Time-Division Multiplexing (TDM) that uses the resource-sharing concept to implement an MAC-SPA and MAC-ISPA filter. The developed dynamically reconfigurable filter is implemented and realized using a 0.18 µm CMOS process. Additional testing was done on the Xilinx xc6vlx760-1ff1760 FPGA device. Relative to the filter that incorporates SPA along with the modified coefficient decimation method (MCDM), the obtained results reveal that the proposed MAC-SPA and MAC-ISPA channel filters, synthesized on FPGA, achieve a reduction in occupied slice count by approximately 7% and 4.76%, respectively. Although their operating speeds are slightly lower by about 9.4% for the MAC-SPA filter and 13.89% for the MAC-ISPA filter, this tradeoff is offset by significant savings in hardware resources, making both designs more area-efficient with only a modest reduction in speed.


  • Open Access

    Design of a low-power hybrid adder with reduced delay using a conditional algorithm-based behavioral model

    by Mohamed Sulaiman S., Dhandapani Vaithiyanathan, Sivakumar N., Britto Pari James

  • Open Access

    An Optimized Hybrid Approach to Denoising of EEG Signals Using CNN and LMS Filtering

    by Suma Nair, Britto Pari James, Man-Fai Leung

    Sleep is a physiological signal which plays a vital role in maintaining human health and well-being. Polysomnographic records provide insights into the various changes occurring during sleep, and hence its study is important in diagnosing various disorders including sleep disorders. As polysomnographic records encapsulate several biological signals, an extraction of EEG signals requires efficient denoising. Thus, a reliable tool for artifact removal is essential in the field of biomedical applications. The CNN is used for its feature extraction and robustness and the least mean square filter for its noise suppression. As the techniques complement one another, a combination of both leads to a better denoised EEG signal. In this approach, CNN is used for the precise removal of artifacts and then an LMS filter is used for its effective adaptation in real-time. The hybridization of both techniques in a hardware-based environment is largely. unexplored. As a result, this study proposes an integration of convolutional neural networks and least mean square filtering for an efficient denoising of EEG signals. Both techniques are optimized to tailor the design to hardware requirements. CNN is refined using the Strassen–Winograd algorithm. The Strassen–Winograd algorithm simplifies matrix multiplication, contributing to a more hardware-optimized design. In this study LMS filtering is analyzed and optimized using several optimizations. The optimizations are two’s complement distributed arithmetic algorithm, offset binary coding-based distributed arithmetic, offset binary coding Radix 4-based distributed arithmetic, as well as a Coordinate Rotation Digital Computer. The CNN with offset binary radix 4 distributed arithmetic-based LMS filter has resulted in a decrease in area of 77% and a decrease in power by 69.1%. But, in terms of Signal to Noise Ratio, Mean Squared Error and Correlation Coefficient, the CNN with offset binary coding distributed arithmetic-based LMS filter has shown better performance. The design was synthesized and implemented in Vivado 19.1. The power and area reduction in this study makes it even more suitable for wearable devices.


  • An Efficient FPGA-Based Welch Power Spectral Density for Real-Time Applications

    by Suma Nair, Britto Pari James

    Power spectral density is a crucial tool in the field of signal processing, mainly in biomedical signal processing. Power spectral density is also one of the most widely used tools in real-time applications. Therefore, further research should be prioritized in the hardware implementation of power spectral density. In this paper, two techniques are introduced in the implementation of power spectral density, mainly focusing on the Fourier transform block. The approaches introduced are the adoption of the Coordinate Rotation Digital Computer algorithm-based fast Fourier transform and the Coordinate Rotation Digital Computer algorithm-based sliding discrete Fourier transform. The other blocks in modified Welch’s architecture are also enhanced using pipelining and approximate distributed arithmetic methods. The introduction of all these techniques has led to an improvement in power and area. There is almost a 36% decrease in the number of lookup tables when compared to the existing methodology. With regards to power, there is almost 44% and 16% decrease in these two architectures, respectively. The overall architectures were synthesized using Xilinx Vivado 19.1, and the language used was Verilog Hardware Description Language.

  • Open Access

    Delineation of Optimized Single and Multichannel Approximate DA-Based Filter Design Using Influential Single MAC Strategy for Trans-Multiplexer

    by Britto Pari James, Leung Man-Fai, Mariammal Karuthapandian, Vaithiyanathan Dhandapani

    In this paper, a multichannel FIR filter design based on the Time Division Multiplex (TDM) approach that incorporates one multiply and add unit, regardless of the variable coefficient length and varying channels, by associating the resource sharing doctrine is suggested. A multiplier based on approximate distributed arithmetic (DA) circuits is employed for effective resource optimization. Although no explicit multiplication was conducted in this realization, the radix-8 and radix-4 Booth algorithms are utilized in the DA framework to curtail and optimize the partial products (PPs). Furthermore, the input stream is truncated with an erratum mending unit to roughly construct the partial products. For an aggregation of PPs, an approximate Wallace tree is taken into consideration to further minimize hardware expenses. Consequently, the suggested design’s latency, utilized area, and power usage are largely reduced. The Xilinx Vertex device is expedited, given the synthesis of the suggested multichannel realization with 16 taps, which is simulated using the Verilog formulary. It is observed that the filter structure with one channel produced the desired results, and the system’s frequency can support up to 429 MHz with a reduced area. Utilizing TSMC 180 nm CMOS technology and the Cadence RC compiler, cell-level performance is also achieved.


  • Open Access

    Reconfigurable Frequency Response Masking Multi-MAC Filters for Software Defined Radio Channelization

    by Subahar Arivalagan, Britto Pari James, Man-Fai Leung

    Mobile technology is currently trending toward supporting multiple communication standards on a single device. This means that some reconfigurable techniques must be the foundation of their design. The two essential requirements of channel filters are minimized complexity and reconfigurability. In this research, a novel extension of Frequency Response Masking (FRM) was investigated by employing Time Division Multiplexing (TDM)-based single Multiply and Accumulate (MAC) architecture using the principle of resource sharing to realize multiple sharp filter responses from a single prototype constant group delay low pass filter. This paper uses a single multiply and add units regardless of the quantity of channels and taps. The suggested reconfigurable filter was synthesized on technology based on 0.18-µm CMOS and put into practice. Further trials were carried out on Virtex-II 2v3000ff1152-4 FPGA device. The outcomes revealed that the suggested channel filter, which was synthesized using FPGA, provides 21.36% of the area curtail and 14.88% of power scaling down on average and put into practice using ASIC provides 5.18% of the area reduction and 9.08% of power scaling down on average.


  • Open Access

    Optimal Realization of Distributed Arithmetic-Based MAC Adaptive FIR Filter Architecture Incorporating Radix-4 and Radix-8 Computation

    by Britto Pari James, Man-Fai Leung, Dhandapani Vaithiyanathan, Karuthapandian Mariammal

    Finite impulse response (FIR) filters are explicitly used in decisive applications such as communication and signal processing areas. Advancement in the latest technologies necessitates specific designs with optimal characteristics. This research work proposes the realization of an efficient distributed arithmetic adaptive FIR filter (DAAFA) architecture using radix-4 and radix-8 computation. Distributed arithmetic (DA) is extensively used to calculate the sum of products without involving a multiplier. The proposed fixed-point realization of a single multiply and accumulate (MAC) FIR adaptive filter is implemented with minimum complex design. The total longest-way computation time is a combination of the delay that occurred in the error calculation module and the delay involved in updating the filter weights. The longest-way computation time of the filter structure is higher, which results in increased latency. In addition, the approximate design of the radix DA multiplier structure is constructed using Booth recoding, partial product formation block and shifting-based accumulation block. Further, the approximate design of DA offers a reduction in complexity and area with respect to the number of slices and enhances the operating speed. The partial product is created using shifters and efficient adders, which further enhances the performance of the realization. This work is implemented in Xilinx and Altera devices and is compared with the present literature. From the synthesis results, it is observed that the propounded design outperforms in terms of complexity, slice delay product and ultimate speed of exertion. The suggested architecture was found to be decisive in terms of area, delay and complexity abatement. The results indicate that the propounded design achieves area reduction (slices) of about 92.03% compared to the existing design. Also, a speed enhancement of about 90.7% is accomplished for the proposed architecture. Nonetheless, the devised architecture utilizes the least means square approach, which enhances the convergence rate notably.