Karuthapandian Mariammal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Karuthapandian Mariammal has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Britto Pari James
Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Chennai 600062, India
2 shared publications - Dhandapani Vaithiyanathan
National Institute of Technology Delhi, Delhi 110036, India
2 shared publications - Man-Fai Leung
Anglia Ruskin University
2 shared publications - A. Abhivandhana
Madras Institute of Technology
1 shared publication - A. J. Ragavkumar
MIT Campus, Anna University
1 shared publication - Anushiya V
UG, Department of Electronics Engineering, Madras Institute of Technology, Anna University, Chennai, India
1 shared publication
Latest Publications
- Open Access
- 3 December 2025
- Published by RSP Science Hub in International Research Journal on Advanced Engineering Hub (IRJAEH)
- Vol. 3 (12) , 4218-4223
Touchless Hospital Bedside Control Using Gesture Sensor
The COVID-19 pandemic and the rise of hospital-acquired infections have underscored the importance of hygienic and contactless solutions in patient care. This project introduces a touchless bedside control system powered by an APDS-9960 gesture sensor and an ESP32 microcontroller, specifically designed to assist patients with limited mobility. Using simple and intuitive hand gestures, patients can operate essential appliances such as fans and lights, and even send emergency alerts to medical staff without physical contact. By minimizing surface interaction, the system promotes infection control, enhances patient independence and comfort, and provides a cost-effective, scalable solution for modern smart hospital environments.
- 3 December 2025
- Published by RSP Science Hub in International Research Journal on Advanced Engineering Hub (IRJAEH)
- Vol. 3 (12) , 4218-4223
Open AccessTouchless Hospital Bedside Control Using Gesture Sensor
The COVID-19 pandemic and the rise of hospital-acquired infections have underscored the importance of hygienic and contactless solutions in patient care. This project introduces a touchless bedside control system powered by an APDS-9960 gesture sensor and an ESP32 microcontroller, specifically designed to assist patients with limited mobility. Using simple and intuitive hand gestures, patients can operate essential appliances such as fans and lights, and even send emergency alerts to medical staff without physical contact. By minimizing surface interaction, the system promotes infection control, enhances patient independence and comfort, and provides a cost-effective, scalable solution for modern smart hospital environments.
- 22 October 2025
- Published by Springer Nature
- p. 757-775
Optimizing Convolutional Neural Network for Accurate Digit Recognition
- 22 October 2025
- Published by Springer Nature
- p. 757-775
Optimizing Convolutional Neural Network for Accurate Digit Recognition
- 30 July 2025
- Published by Springer Nature
- p. 301-323
Design and Implementation of Application-Specific UTMI with SIE
- 30 July 2025
- Published by Springer Nature
- p. 301-323
Design and Implementation of Application-Specific UTMI with SIE
- Open Access
- 3 June 2025
- Published by RSP Science Hub in International Research Journal on Advanced Engineering Hub (IRJAEH)
- Vol. 3 (06) , 2869-2875
Adaptive Filter-Based Grey Wolf Optimization Algorithm for Enhanced Medical Diagnosis
Medical diagnostic systems often struggle with noise and data inconsistencies in physiological signals. This paper presents an Adaptive Filter-Based Grey Wolf Optimization (AF-GWO) algorithm that combines adaptive filtering for noise reduction and GWO for optimizing machine learning classifiers. The method was evaluated on biomedical datasets, including ECG and heart disease data, and compared with conventional techniques like GA and PSO. Results show that AF-GWO significantly improves classification accuracy, signal-to-noise ratio (SNR), and convergence speed. This hybrid approach provides an effective solution for real-time medical diagnostics, enhancing feature optimization and signal clarity. The framework demonstrates strong potential for AI-driven medical applications. Future work will explore its application in multimodal medical datasets.
- 3 June 2025
- Published by RSP Science Hub in International Research Journal on Advanced Engineering Hub (IRJAEH)
- Vol. 3 (06) , 2869-2875
Open AccessAdaptive Filter-Based Grey Wolf Optimization Algorithm for Enhanced Medical Diagnosis
Medical diagnostic systems often struggle with noise and data inconsistencies in physiological signals. This paper presents an Adaptive Filter-Based Grey Wolf Optimization (AF-GWO) algorithm that combines adaptive filtering for noise reduction and GWO for optimizing machine learning classifiers. The method was evaluated on biomedical datasets, including ECG and heart disease data, and compared with conventional techniques like GA and PSO. Results show that AF-GWO significantly improves classification accuracy, signal-to-noise ratio (SNR), and convergence speed. This hybrid approach provides an effective solution for real-time medical diagnostics, enhancing feature optimization and signal clarity. The framework demonstrates strong potential for AI-driven medical applications. Future work will explore its application in multimodal medical datasets.
- Open Access
Delineation of Optimized Single and Multichannel Approximate DA-Based Filter Design Using Influential Single MAC Strategy for Trans-Multiplexer
In this paper, a multichannel FIR filter design based on the Time Division Multiplex (TDM) approach that incorporates one multiply and add unit, regardless of the variable coefficient length and varying channels, by associating the resource sharing doctrine is suggested. A multiplier based on approximate distributed arithmetic (DA) circuits is employed for effective resource optimization. Although no explicit multiplication was conducted in this realization, the radix-8 and radix-4 Booth algorithms are utilized in the DA framework to curtail and optimize the partial products (PPs). Furthermore, the input stream is truncated with an erratum mending unit to roughly construct the partial products. For an aggregation of PPs, an approximate Wallace tree is taken into consideration to further minimize hardware expenses. Consequently, the suggested design’s latency, utilized area, and power usage are largely reduced. The Xilinx Vertex device is expedited, given the synthesis of the suggested multichannel realization with 16 taps, which is simulated using the Verilog formulary. It is observed that the filter structure with one channel produced the desired results, and the system’s frequency can support up to 429 MHz with a reduced area. Utilizing TSMC 180 nm CMOS technology and the Cadence RC compiler, cell-level performance is also achieved.
Open AccessDelineation of Optimized Single and Multichannel Approximate DA-Based Filter Design Using Influential Single MAC Strategy for Trans-Multiplexer
In this paper, a multichannel FIR filter design based on the Time Division Multiplex (TDM) approach that incorporates one multiply and add unit, regardless of the variable coefficient length and varying channels, by associating the resource sharing doctrine is suggested. A multiplier based on approximate distributed arithmetic (DA) circuits is employed for effective resource optimization. Although no explicit multiplication was conducted in this realization, the radix-8 and radix-4 Booth algorithms are utilized in the DA framework to curtail and optimize the partial products (PPs). Furthermore, the input stream is truncated with an erratum mending unit to roughly construct the partial products. For an aggregation of PPs, an approximate Wallace tree is taken into consideration to further minimize hardware expenses. Consequently, the suggested design’s latency, utilized area, and power usage are largely reduced. The Xilinx Vertex device is expedited, given the synthesis of the suggested multichannel realization with 16 taps, which is simulated using the Verilog formulary. It is observed that the filter structure with one channel produced the desired results, and the system’s frequency can support up to 429 MHz with a reduced area. Utilizing TSMC 180 nm CMOS technology and the Cadence RC compiler, cell-level performance is also achieved.
- Open Access
- 6 September 2024
- Published by MDPI AG in Electronics
- Vol. 13 (17) , 3551
Optimal Realization of Distributed Arithmetic-Based MAC Adaptive FIR Filter Architecture Incorporating Radix-4 and Radix-8 Computation
Finite impulse response (FIR) filters are explicitly used in decisive applications such as communication and signal processing areas. Advancement in the latest technologies necessitates specific designs with optimal characteristics. This research work proposes the realization of an efficient distributed arithmetic adaptive FIR filter (DAAFA) architecture using radix-4 and radix-8 computation. Distributed arithmetic (DA) is extensively used to calculate the sum of products without involving a multiplier. The proposed fixed-point realization of a single multiply and accumulate (MAC) FIR adaptive filter is implemented with minimum complex design. The total longest-way computation time is a combination of the delay that occurred in the error calculation module and the delay involved in updating the filter weights. The longest-way computation time of the filter structure is higher, which results in increased latency. In addition, the approximate design of the radix DA multiplier structure is constructed using Booth recoding, partial product formation block and shifting-based accumulation block. Further, the approximate design of DA offers a reduction in complexity and area with respect to the number of slices and enhances the operating speed. The partial product is created using shifters and efficient adders, which further enhances the performance of the realization. This work is implemented in Xilinx and Altera devices and is compared with the present literature. From the synthesis results, it is observed that the propounded design outperforms in terms of complexity, slice delay product and ultimate speed of exertion. The suggested architecture was found to be decisive in terms of area, delay and complexity abatement. The results indicate that the propounded design achieves area reduction (slices) of about 92.03% compared to the existing design. Also, a speed enhancement of about 90.7% is accomplished for the proposed architecture. Nonetheless, the devised architecture utilizes the least means square approach, which enhances the convergence rate notably.
- 6 September 2024
- Published by MDPI AG in Electronics
- Vol. 13 (17) , 3551
Open AccessOptimal Realization of Distributed Arithmetic-Based MAC Adaptive FIR Filter Architecture Incorporating Radix-4 and Radix-8 Computation
Finite impulse response (FIR) filters are explicitly used in decisive applications such as communication and signal processing areas. Advancement in the latest technologies necessitates specific designs with optimal characteristics. This research work proposes the realization of an efficient distributed arithmetic adaptive FIR filter (DAAFA) architecture using radix-4 and radix-8 computation. Distributed arithmetic (DA) is extensively used to calculate the sum of products without involving a multiplier. The proposed fixed-point realization of a single multiply and accumulate (MAC) FIR adaptive filter is implemented with minimum complex design. The total longest-way computation time is a combination of the delay that occurred in the error calculation module and the delay involved in updating the filter weights. The longest-way computation time of the filter structure is higher, which results in increased latency. In addition, the approximate design of the radix DA multiplier structure is constructed using Booth recoding, partial product formation block and shifting-based accumulation block. Further, the approximate design of DA offers a reduction in complexity and area with respect to the number of slices and enhances the operating speed. The partial product is created using shifters and efficient adders, which further enhances the performance of the realization. This work is implemented in Xilinx and Altera devices and is compared with the present literature. From the synthesis results, it is observed that the propounded design outperforms in terms of complexity, slice delay product and ultimate speed of exertion. The suggested architecture was found to be decisive in terms of area, delay and complexity abatement. The results indicate that the propounded design achieves area reduction (slices) of about 92.03% compared to the existing design. Also, a speed enhancement of about 90.7% is accomplished for the proposed architecture. Nonetheless, the devised architecture utilizes the least means square approach, which enhances the convergence rate notably.