EEErgün Ekici

Ergün Ekici

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ergün Ekici has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Optimization of low velocity impact parameters of thermoplastic based fiber metal laminate composites using Taguchi based desirability function approach

    by Ergün Ekici, Mustafa Dündar

    Fiber metal laminates (FMLs) combine the high specific strength and damage tolerance of metals with the light weight and fatigue resistance of fiber-reinforced composites, overcoming key limitations of conventional monolithic materials. Replacing thermoset matrices with thermoplastics further improves recyclability and repairability, yet the low-velocity impact behavior of thermoplastic-based FMLs (T-FMLs) under varying impact energy and ambient temperature, and the systematic identification of optimum parameters, remains insufficiently understood. This study addresses that gap by combining, for the first time for T-FML systems, a Taguchi-based multi-parameter experimental design with a PCA-based composite desirability function to jointly characterize and optimize low-velocity impact response. PP- and PA-6-based T-FMLs were subjected to low-velocity impact tests at three impact energies and three ambient temperatures (−40, 25, and 80°C), and tensile tests at room temperature were additionally performed for both resin systems. A Taguchi L18 orthogonal array was used to evaluate the individual and combined effects of resin type, impact energy, and temperature, with analysis of variance (ANOVA) applied to assess parameter significance and contribution ratios. Impact energy was found to be the dominant factor governing impact response, while resin type and temperature had comparatively minor effects; post-impact examination further revealed interlaminar delamination in PA-6-based T-FMLs under certain conditions. Notably, although not originally targeted in the experimental design, a PP film interlayer was found to improve interfacial properties. The PCA-based desirability function identified PA-6 resin, an impact energy of 30 J, and a temperature of −40°C as the optimum condition for maximizing impact force while minimizing displacement and damage.

  • Open Access

    Numerical and Statistical İnvestigation Of The Effect Of Composite Layer Thickness On Low-Velocity İmpact Behaviour in Fibre Metal Laminate Materials

    by Mustafa Dündar, İlYas Uygur, Ergün Ekici, Cihat Taşçıoğlu, Behçet Gülenç

    In the field of aviation, reducing fuel costs by designing lighter vehicles and thus producing more environmentally friendly aircraft is one of the most important issues. This situation has led aircraft manufacturers to search for lighter and more durable materials. For this reason, Fibre Metal Laminate (FML) structures, which are used especially in the aerospace industry due to their superior fatigue and impact resistance properties, attract attention. Carbon fibre reinforced aluminium plates (CARALL), the most unique member of the FML hybrid structure family, has attracted the attention of researchers. In this study, the low velocity impact behaviour of CARALL FML structures with different composite layer thicknesses at different energy loading (8J-12J-18J) and different impactor types (Ø15 and Ø20) were statistically investigated. CARALL FML structures were modelled in 2/1 arrangement (Al-〖0°〗_([1])-Al, Al-〖0°〗_([3])-Al, Al-〖0°〗_([5])-Al) in LS-DYNA finite element programme. It is observed that the peak load Fmax increases with increasing energy loading. The increase in striker diameter decreased the amount of absorbed energy and increased the rebound.


  • Delamination and thrust force analysis in GLARE: Influence of tool geometry and prediction with machine learning models

    by Ergün Ekici, İbRahim Pazarkaya, Gültekin Uzun

    The multi-layered (fiber/metal) structure of glass fibre aluminium reinforced epoxy (GLARE) makes it difficult to obtain acceptable damage-free holes that meet aerospace standards. This paper investigated the effects of tool geometry and drilling parameters on reducing delamination damage and uncut fibers at the hole exit surface in drilling GLARE. The hole surfaces were examined by scanning electron microscope (SEM) at various magnifications. In addition, deep neural network (DNN) and long-short-term memory (LSTM) machine learning models were used to predict delamination (F da ), uncut fiber (UCF), and thrust forces using experimental data. No positive contribution of the special geometry tool was observed, while the standard geometry tool was found to be ideal for drilling conditions. Analysis of variance (ANOVA) revealed that feed rate contributed 57.83% to delamination damage, while tool geometry contributed 74.31% and 92.33% for uncut fiber and thrust force, respectively. SEM analysis revealed high deformation zones in the aluminum layers and fiber fracture and separation in the glass fibre reinforced polymer (GFRP) layers. DNN and LSTM models were found to provide accurate predictions with R 2 values greater than 95% and 98%, respectively.


  • Optimization of low-velocity impact behavior of FML structures at different environmental temperatures using taguchi method and grey relational analysis

    by Mustafa Dündar, İlYas Uygur, Ergün Ekici

    Carbon fiber-reinforced Aluminum Laminate (CARALL) is a new generation of Fibre Metal Laminate (FML) material. This study investigates the low-velocity impact behavior of CARALL structures at different environmental temperatures (−40°C, 23°C, and 80°C). Two different groups of CARALL composite structures with varying fiber orientations were produced by hot pressing in a 3/2 arrangement: C1 (Al/0°90°/Al/90°0°/Al) and C2 (Al/0°0°/Al/0°0°/Al). Low-velocity impact tests were conducted at 23 J, 33 J, and 48 J energy levels using a Ø20 mm spherical impactor tip. The area of damage was detected by ultrasonic C-Scan. In addition, analysis of variance (ANOVA) was applied to reveal the influential parameters and their effect levels. After conducting experiments using the Taguchi L 18 test set, it was observed that the C2-coded specimen yielded better results in terms of maximum peak load, maximum displacement, and damage area. While the decrease in temperature increased the damage and maximum peak load, the increase in temperature did not cause a significant change in the maximum peak load. The primary damage mechanisms observed in damage investigations were matrix cracks and delamination between composite layers. Although delamination is present between the Al/CFRP layer, it is not significant. According to ANOVA results, impact energy was the most effective parameter for maximum impact force, maximum displacement, and damage area, with contribution rates of 81%, 74%, and 76%, respectively. The optimal experimental conditions (23°C temperature and 23 J impact energy with the C1-coded sample) were determined using grey relational analysis based on principal component analysis.


  • Open Access

    SANDVİÇ KOMPOZİTLERİN DELİNMESİNDE DELAMİNASYON FAKTÖRÜNÜN İNCELENMESİ

    by Abdil Kuş, Ergün Eki̇cİ

    Bu çalışmada bal peteği geometrisinde farklı çekirdek malzemelerden üretilen sandviç kompozitlerin delinmesinde delik giriş ve çıkış bölgesinde oluşan delaminasyon faktörü araştırılmıştır. Taguchi metodu L 18 tasarımına göre yapılan deneylerde kontrol faktörleri olarak kesme hızı, ilerleme miktarı ve çekirdek malzeme tipi esas alınmıştır. Deneyler CNC dik işleme merkezinde 6,3 mm çapında TiAlN kaplı karbür matkap kullanılarak gerçekleştirilmiştir. Ayrıca %95 güven seviyesinde varyans analizi (ANOVA) uygulanmış, giriş ve çıkış bölgeleri hasarı için optimum parametreler belirlenmiştir. Her iki numunede delme işlemi sonrasında tüm deney şartlarında deliklerin optik görüntüleri alınmış ve en yüksek kesme parametreleri için delik çıkış bölgesinde oluşan hasar tipleri incelenmiştir. Delaminasyon faktörü üzerinde en etkili parametre delik giriş bölgesi için %46 katkı oranı ile kesme hızı, çıkış bölgesi içinse %32,8 katkı oranı ile ilerleme miktarı olmuştur. Özellikle delik çıkış bölgesinde oluşan hasar tipleri delaminasyon, kesilmemiş elyaf ve parçalanma olduğu görülmüştür.


  • Mechanical and fracture behavior of B4C reinforced Al composites produced by hot pressing

    by Ergün Ekici, Yusuf Özçatalbaş, Mahmut Gülesin

    In this study, the effects of particle addition on the microstructure, mechanical properties and fracture behaviors of Al/B4C particle reinforced composite produced by hot pressing method were investigated. After the production of 5, 10 and 15 wt.-% of B4C reinforced composites, T6 heat treatment was applied. It was specified that a strong interface bond occurred between the matrix and particles, and during the fracturing of composites, this effect increased the particle fracture. It was observed that particles were fractured parallel to the fracture surface and to each other fracture surface of MMCp. In general, cavity of particle separated from the matrix was not seen. In the production of MMCp, it was also observed that hot pressing provided a density higher than 99 %. After the heat treatment the maximum hardness value of 173 HB was reached with 15 wt.-% B4C reinforced sample. The transverse rupture strength (TRS) decreased with the increase of reinforcement ratio. The highest TRS was 510 MPa with the 5 wt.-% reinforced material, whereas the lowest value was obtained to be 387 MPa with the 15 wt.-% B4C reinforced material.


  • Milling behavior of Hadfield steel with cryogenically treated tungsten carbide inserts

    by Ergün Ekici

    In this study, the performance of cryogenically treated tungsten carbide inserts in the milling of Hadfield steel (X120Mn12) was evaluated in terms of surface roughness (Ra) and tool wear (VB). Cutting tools were assessed under three conditions: untreated (U), cryogenic treated (CT) and cryo-tempered (CTT). For the cutting parameters, three different cutting speeds (70, 100 and 130 m·min−1) and feed rates (0.08, 0.14 and 0.2 mm·rev−1) were used. The experiments were carried out under a fixed depth of cut and dry cutting conditions. To determine the factorial effects, the procedure Taguchi L27 (33) was used. For the estimation of Ra and VB, the response surface method (RSM) was employed and mathematical models were developed. In terms of Ra, the effective parameter was feed rate (89.45 %) and in terms of VB, it was the cutting speed (60.42 %). For Ra and VB, the optimum levels of factors were determined as A3B3C1 and A3B1C1, respectively. The effects of the factors were also assessed by RSM.


  • Evaluation of surface roughness and material removal rate in the wire electrical discharge machining of Al/B4C composites via the Taguchi method

    by Ergün Ekici, Ali Riza Motorcu, Abdil Kuş

    This study researched the effects of machining parameters on surface roughness and material removal rate in the wire electrical discharge cutting of high-density Al/B4C metal matrix composites produced via the hot pressing method. Wire tension, reinforcement percentage, wire speed, pulse-on time and pulse-off time were set as the control factors. The Taguchi L18 (21 × 34) orthogonal array was used in the experiment design and determination of the optimum control factors. Variance analysis was applied to determine the effects of the control factors on the surface roughness and material removal rate. The results showed the most effective parameters to be pulse-on time (30.22%) for surface roughness and wire speed (83.20%) for material removal rate, and the optimum levels of the control factors to be A2B1C2D1E1 and A2B2C3D2E2, respectively. Predictive equations were then developed by applying linear regression analysis, and the adjusted correlation coefficients were calculated as 0.61 for surface roughness and 0.785 for material removal rate.