Lumír Hružík
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lumír Hružík has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Adam Bureček
Department of Hydromechanics and Hydraulic Equipment, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic
8 shared publications - Martin Vašina
Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic
7 shared publications - Marian Ledvoň
Department of Hydromechanics and Hydraulic Equipment, VSB-Technical University of Ostrava, Ostrava, Czech Republic
4 shared publications - Tomáš Polášek
Department of Hydromechanics and Hydraulic Equipment, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic
4 shared publications Adam Bureček
Technical University of Ostrava
3 shared publications- Filip Dýrr
Department of Hydromechanics and Hydraulic Equipment, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 708 00 Ostrava, Czech Republic
3 shared publications
Latest Publications
- Open Access
Assessment of Different Levels of Blackcurrant Juice and Furcellaran on the Quality of Fermented Whey-Based Beverages Using Rheological and Mechanical Vibration Damping Techniques
In the current study, fermented whey-based beverage models with different levels of blackcurrant juice (0; 10; 20; 100% (w/w)) and furcellaran (0.25% and 0.50% (w/w)) were produced and evaluated. Physicochemical, rheological, mechanical vibration damping, and sensory analyses were performed. During fermentation (48 h), the values of pH, density, and total soluble solids decreased. On the other hand, the ethanol content during fermentation increased up to a final content in the range of 0.92–4.86% (v/v). The addition of furcellaran was effective in terms of sediment content decrease to a level of 0.25% (w/w). In general, the samples exhibited non-Newtonian pseudoplastic behaviour. The sensory analysis revealed that the sample with a composition of 20% (w/w) blackcurrant juice and 0.50% (w/w) furcellaran received the highest score.
Open AccessAssessment of Different Levels of Blackcurrant Juice and Furcellaran on the Quality of Fermented Whey-Based Beverages Using Rheological and Mechanical Vibration Damping Techniques
In the current study, fermented whey-based beverage models with different levels of blackcurrant juice (0; 10; 20; 100% (w/w)) and furcellaran (0.25% and 0.50% (w/w)) were produced and evaluated. Physicochemical, rheological, mechanical vibration damping, and sensory analyses were performed. During fermentation (48 h), the values of pH, density, and total soluble solids decreased. On the other hand, the ethanol content during fermentation increased up to a final content in the range of 0.92–4.86% (v/v). The addition of furcellaran was effective in terms of sediment content decrease to a level of 0.25% (w/w). In general, the samples exhibited non-Newtonian pseudoplastic behaviour. The sensory analysis revealed that the sample with a composition of 20% (w/w) blackcurrant juice and 0.50% (w/w) furcellaran received the highest score.
- Open Access
Static Characteristics and Energy Consumption of the Pressure-Compensated Pump
The motivation of this research was to assess the possibility of speed control for the selected pressure-compensated pump. Measured static characteristics of an axial piston pump with pressure compensation are presented in the paper. Based on these characteristics, the pump efficiencies are determined. The characteristics and efficiencies are determined for the different pump outlet pressures, pump speeds, relative displacements and for the different pressures set at the pressure compensator. In addition, the different methods of pump control were compared. These are displacement control, speed control and both controls. The efficiency of each control method was compared based on the determined mechanical input power at the pump drive shaft. By comparing these control methods, it was found that the combination of both control methods can achieve up to 93% savings of mechanical power in the controlled state (stand-by state). Also, the adverse effects resulting from each control method that reduces pump efficiency were defined.
Open AccessStatic Characteristics and Energy Consumption of the Pressure-Compensated Pump
The motivation of this research was to assess the possibility of speed control for the selected pressure-compensated pump. Measured static characteristics of an axial piston pump with pressure compensation are presented in the paper. Based on these characteristics, the pump efficiencies are determined. The characteristics and efficiencies are determined for the different pump outlet pressures, pump speeds, relative displacements and for the different pressures set at the pressure compensator. In addition, the different methods of pump control were compared. These are displacement control, speed control and both controls. The efficiency of each control method was compared based on the determined mechanical input power at the pump drive shaft. By comparing these control methods, it was found that the combination of both control methods can achieve up to 93% savings of mechanical power in the controlled state (stand-by state). Also, the adverse effects resulting from each control method that reduces pump efficiency were defined.
- Open Access
The Effect of Braid Angle on Hydraulic Hose Geometry
Hydraulic hoses are part of most hydraulic systems, from industrial hydraulics with open loop hydraulic systems to mobile hydraulics with closed loop hydraulic systems. The design parameters of hydraulic hoses may influence the duty cycle dynamics of these systems. One of the factors that influence the behavior of a hydraulic hose under pressure loading is the steel braid angle with respect to the hydraulic hose axis. This work aims to determine the effect of the hydraulic hose braid angle on the change in its geometry. The next objective is to determine the forces that occur at the hose ends under pressure loading. The stresses occur when fluid pressure is applied to the inner wall of the hydraulic hose. Consequently, these stresses are transferred to the hose ends through the steel braid or spiral. The phenomenon of the neutral braid angle provides a balance between the stresses generated inside the hydraulic hose. Therefore, hydraulic hose manufacturers try to produce hydraulic hoses with a neutral braid angle, because the lifetime of the hydraulic hose is also related to this. As part of this research work, an experimental device was constructed in order to measuring the properties of hydraulic hoses. When the hose was loaded with fluid pressure, the change in hose geometry was measured and the angle of the hose braid was measured simultaneously. Upon the measurements, the effect of the braid angle on the hose behavior under pressure loading was determined.
Open AccessThe Effect of Braid Angle on Hydraulic Hose Geometry
Hydraulic hoses are part of most hydraulic systems, from industrial hydraulics with open loop hydraulic systems to mobile hydraulics with closed loop hydraulic systems. The design parameters of hydraulic hoses may influence the duty cycle dynamics of these systems. One of the factors that influence the behavior of a hydraulic hose under pressure loading is the steel braid angle with respect to the hydraulic hose axis. This work aims to determine the effect of the hydraulic hose braid angle on the change in its geometry. The next objective is to determine the forces that occur at the hose ends under pressure loading. The stresses occur when fluid pressure is applied to the inner wall of the hydraulic hose. Consequently, these stresses are transferred to the hose ends through the steel braid or spiral. The phenomenon of the neutral braid angle provides a balance between the stresses generated inside the hydraulic hose. Therefore, hydraulic hose manufacturers try to produce hydraulic hoses with a neutral braid angle, because the lifetime of the hydraulic hose is also related to this. As part of this research work, an experimental device was constructed in order to measuring the properties of hydraulic hoses. When the hose was loaded with fluid pressure, the change in hose geometry was measured and the angle of the hose braid was measured simultaneously. Upon the measurements, the effect of the braid angle on the hose behavior under pressure loading was determined.
- Open Access
Experimental and Numerical Analysis of Flow Force Acting on the Spool of Proportional Directional Valve
This paper deals with the experimental and numerical analysis of the flow force acting on the spool of a proportional directional valve. The flow force arises due to the fluid flow through the flow path of the proportional directional valve and significantly influences the dynamics of the valve spool. The valve under investigation is a three-position four-way proportional directional valve with zero spool lap and feedback from the spool position. The dependence of the valve spool flow force on the volumetric flow rate is measured as part of the experiment. The measurements are performed for different spool displacements. The measured data will be used to verify the numerical simulations. The proportional directional valve was modified so that a force sensor could be included on the spool axis to realize the experiment. Firstly, the flow force is measured as the fluid passes through the two flow paths of the valve (PB and AT). Subsequently, the experimental setup is modified to determine the flow force when the fluid passes through each flow path separately. The measurements are compared. Simulations of the flow through the proportional directional valve are performed using Ansys Fluent 2022 R2 software to determine the flow forces acting on the valve spool. Simulations are performed for the selected spool positions of the proportional directional valve. Finally, the results of the simulation and the experiment are compared. The contribution of this study is a CFD model of the flow paths of the proportional directional valve verified by experiment. The CFD model will allow the flow force analysis for different flow path geometries of the investigated valve. Experimental analysis of flow force is performed over the entire spool stroke at different volumetric flow rates. The flow forces are measured for each flow path separately and for both flow paths simultaneously.
Open AccessExperimental and Numerical Analysis of Flow Force Acting on the Spool of Proportional Directional Valve
This paper deals with the experimental and numerical analysis of the flow force acting on the spool of a proportional directional valve. The flow force arises due to the fluid flow through the flow path of the proportional directional valve and significantly influences the dynamics of the valve spool. The valve under investigation is a three-position four-way proportional directional valve with zero spool lap and feedback from the spool position. The dependence of the valve spool flow force on the volumetric flow rate is measured as part of the experiment. The measurements are performed for different spool displacements. The measured data will be used to verify the numerical simulations. The proportional directional valve was modified so that a force sensor could be included on the spool axis to realize the experiment. Firstly, the flow force is measured as the fluid passes through the two flow paths of the valve (PB and AT). Subsequently, the experimental setup is modified to determine the flow force when the fluid passes through each flow path separately. The measurements are compared. Simulations of the flow through the proportional directional valve are performed using Ansys Fluent 2022 R2 software to determine the flow forces acting on the valve spool. Simulations are performed for the selected spool positions of the proportional directional valve. Finally, the results of the simulation and the experiment are compared. The contribution of this study is a CFD model of the flow paths of the proportional directional valve verified by experiment. The CFD model will allow the flow force analysis for different flow path geometries of the investigated valve. Experimental analysis of flow force is performed over the entire spool stroke at different volumetric flow rates. The flow forces are measured for each flow path separately and for both flow paths simultaneously.
- Open Access
Leakage Characteristics of Proportional Directional Valve
This paper deals with the analysis of leakage characteristics of the proportional directional valve. These characteristics distinguish a real directional valve from an ideal one. The ideal directional valve is characterized by zero leakage due to its perfect geometry. The investigated element is the three-position four-way proportional directional valve with zero spool lap and feedback from the spool position. The spool position is measured by the inductive position sensor and processed by external electronics. Internal leakage occurs due to axial and radial clearances between the spool and the sleeve. The magnitude of axial clearances that occur at throttle edges and their effect on the directional valve leakage is the subject of research. The blocked-line pressure sensitivity curve, the leakage flow curve and the center flow curve are determined by experiment. Individual characteristics are determined for different working fluid temperatures and different supply pressures. The flow through internal leaks in the center position of the valve spool is determined by analytical calculations. The flow through internal leaks is also simulated using the Ansys Fluent software. Subsequently, the geometry of the flow simulation model is modified to take into account manufacturing tolerances. From simulation results, the effect of the manufacturing tolerance magnitude on the internal leakage of the directional valve is evaluated. Finally, simulated dependencies are compared with experimentally determined characteristics.
Open AccessLeakage Characteristics of Proportional Directional Valve
This paper deals with the analysis of leakage characteristics of the proportional directional valve. These characteristics distinguish a real directional valve from an ideal one. The ideal directional valve is characterized by zero leakage due to its perfect geometry. The investigated element is the three-position four-way proportional directional valve with zero spool lap and feedback from the spool position. The spool position is measured by the inductive position sensor and processed by external electronics. Internal leakage occurs due to axial and radial clearances between the spool and the sleeve. The magnitude of axial clearances that occur at throttle edges and their effect on the directional valve leakage is the subject of research. The blocked-line pressure sensitivity curve, the leakage flow curve and the center flow curve are determined by experiment. Individual characteristics are determined for different working fluid temperatures and different supply pressures. The flow through internal leaks in the center position of the valve spool is determined by analytical calculations. The flow through internal leaks is also simulated using the Ansys Fluent software. Subsequently, the geometry of the flow simulation model is modified to take into account manufacturing tolerances. From simulation results, the effect of the manufacturing tolerance magnitude on the internal leakage of the directional valve is evaluated. Finally, simulated dependencies are compared with experimentally determined characteristics.
- Open Access
Comparative Study of Chip Formation in Orthogonal and Oblique Slow-Rate Machining of EN 16MnCr5 Steel
In today’s unmanned productions systems, it is very important that the manufacturing processes are carried out efficiently and smoothly. Therefore, controlling chip formation becomes an essential issue to be dealt with. It can be said that the material removal from a workpiece using machining is based on the degradation of material cohesion made in a controlled manner. The aim of the study was to understand the chip formation mechanisms that can, during uncontrolled processes, result in the formation and propagation of microcracks on the machined surface and, as such, cause failure of a component during its operation. This article addresses some aspects of chip formation in the orthogonal and oblique slow-rate machining of EN 16MnCr5 steel. In order to avoid chip root deformation and its thermal influence on sample acquisition, that could cause the changes in the microstructure of material, a new reliable method for sample acquisition has been developed in this research. The results of the experiments have been statistically processed. The obtained dependencies have uncovered how the cutting tool geometry and cutting conditions influence a chip shape, temperature in cutting area, or microhardness according to Vickers in the area of shear angle.
Open AccessComparative Study of Chip Formation in Orthogonal and Oblique Slow-Rate Machining of EN 16MnCr5 Steel
In today’s unmanned productions systems, it is very important that the manufacturing processes are carried out efficiently and smoothly. Therefore, controlling chip formation becomes an essential issue to be dealt with. It can be said that the material removal from a workpiece using machining is based on the degradation of material cohesion made in a controlled manner. The aim of the study was to understand the chip formation mechanisms that can, during uncontrolled processes, result in the formation and propagation of microcracks on the machined surface and, as such, cause failure of a component during its operation. This article addresses some aspects of chip formation in the orthogonal and oblique slow-rate machining of EN 16MnCr5 steel. In order to avoid chip root deformation and its thermal influence on sample acquisition, that could cause the changes in the microstructure of material, a new reliable method for sample acquisition has been developed in this research. The results of the experiments have been statistically processed. The obtained dependencies have uncovered how the cutting tool geometry and cutting conditions influence a chip shape, temperature in cutting area, or microhardness according to Vickers in the area of shear angle.
- Open Access
- 1 September 2018
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 25 (Supplement) , 382-390
Energy and Dynamic Properties of Hydraulic Systems
The aim of the paper is to evaluate hydraulic systems in terms of energy and dynamic properties. There are flow and pressure losses that have influence on total efficiency of hydraulic systems. The systems are compared from lower...
- 1 September 2018
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 25 (Supplement) , 382-390
Open AccessEnergy and Dynamic Properties of Hydraulic Systems
The aim of the paper is to evaluate hydraulic systems in terms of energy and dynamic properties. There are flow and pressure losses that have influence on total efficiency of hydraulic systems. The systems are compared from lower...
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020001
Investigation of flow for check valves using the optimization method
The check valves are used to control the flow of the working fluid in one direction and avoid flow in the reverse direction and are used where an undesirable reverse flow occurs. Experimental and mathematical methods can be used to examine the characteristics of the check valve. Optimization method can be used to modify the construction design to improve operating parameters. This method has been applied to the check valve. The result is an evaluation of the usability of the Adjoint Solver (Fluent) to reduce the valve resistance.
- 7 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2000 (1) , 020001
Investigation of flow for check valves using the optimization method
The check valves are used to control the flow of the working fluid in one direction and avoid flow in the reverse direction and are used where an undesirable reverse flow occurs. Experimental and mathematical methods can be used to examine the characteristics of the check valve. Optimization method can be used to modify the construction design to improve operating parameters. This method has been applied to the check valve. The result is an evaluation of the usability of the Adjoint Solver (Fluent) to reduce the valve resistance.
- Open Access
- 1 December 2017
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 24 (6) , 1905-1914
Mathematical simulation and measurement of expansion of hydraulic hose with oil
Rad se bavi mjerenjem i matematičkom simulacijom širenja hidrauličnog crijeva, uključujući učinak modula stlačivosti ulja. Youngov modul elastičnosti hidrauličnog crijeva eksperimentalno je određen metodom ekspanzije i metodom...
- 1 December 2017
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 24 (6) , 1905-1914
Open AccessMathematical simulation and measurement of expansion of hydraulic hose with oil
Rad se bavi mjerenjem i matematičkom simulacijom širenja hidrauličnog crijeva, uključujući učinak modula stlačivosti ulja. Youngov modul elastičnosti hidrauličnog crijeva eksperimentalno je određen metodom ekspanzije i metodom...
- Open Access
- 1 June 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (3) , 296-302
Dynamics of Linear Hydraulic Cylinder with Mass Load
The paper deals with examination of dynamics of linear hydraulic cylinder with mass load. The hydraulic cylinder is placed in vertical position. There is experimentally simulated a system state. In this case a higher piston velocity is achieve...
- 1 June 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (3) , 296-302
Open AccessDynamics of Linear Hydraulic Cylinder with Mass Load
The paper deals with examination of dynamics of linear hydraulic cylinder with mass load. The hydraulic cylinder is placed in vertical position. There is experimentally simulated a system state. In this case a higher piston velocity is achieve...