Graham T. Reader
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Graham T. Reader has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ming Zheng
Department of Mechanical, Automotive and Materials Engineering University of Windsor 401 Sunset Avenue N9B 3P4 Windsor ON Canada
2 shared publications - Binghao Cong
Department of Mechanical, Automotive, and Materials Engineering (MAME), University of Windsor , Windsor, ON N9B 3P4, Canada
1 shared publication - Jimi Tjong
PERDC, Ford, Windsor, ON N9A 6X3, Canada
1 shared publication Meiping Wang
University of Windsor, Windsor, Ontario N9B 3P4, Canada
1 shared publicationMing Zheng
University of Windsor, Windsor, Ontario N9B 3P4, Canada
1 shared publication- Navjot Sandhu
Department of Mechanical, Automotive, and Materials Engineering (MAME), University of Windsor , Windsor, ON N9B 3P4, Canada
1 shared publication
Latest Publications
- 20 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-10
Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine
Compression ignition (CI) diesel engines offer power-dense solutions for heavy-duty vehicles. The purpose of combustion management for diesel engines primarily concerns the balance of high efficiency and low emissions. Conventional single-shot diesel combustion involves extended overlap of fuel injection and combustion, promoting diffusion combustion, which is efficient yet prone to form excessive amounts of nitrogen oxides and soot emissions. The application of exhaust gas dilution to reduce NOx below regulation limits leads to an increase in smoke emissions, further magnifying the emission control dilemma. Dimethyl ether (DME) contains suitable reactivity for compression ignition engines while also possessing distinct characteristics to diesel, notably physical properties such as volatility and high oxygen content, that eliminates engine-out soot concerns. In turn, DME enables direct NOx control via oxygen dilution. Nonetheless, the influence of charge dilution toward the combustion heat release behavior of DME persists. This study investigated heat release patterns of high-pressure DME combustion using a single-shot fuel scheduling, with injection timing fixed at top dead center (TDC). Throughout the study, the injection pressure, engine load, and oxygen dilution were adjusted separately to characterize their influence on the subsequent combustion process. Diesel combustion operated at matching conditions was used to provide relevance to the results. Most notably, the period of diffusion burning was extended in DME following a longer period of injection–combustion overlap. To add, the heat release of DME combustion was repeatedly shorter than diesel owing to the lack of end-burning combustion phase inherent to diesel combustion.
- 20 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-10
Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine
Compression ignition (CI) diesel engines offer power-dense solutions for heavy-duty vehicles. The purpose of combustion management for diesel engines primarily concerns the balance of high efficiency and low emissions. Conventional single-shot diesel combustion involves extended overlap of fuel injection and combustion, promoting diffusion combustion, which is efficient yet prone to form excessive amounts of nitrogen oxides and soot emissions. The application of exhaust gas dilution to reduce NOx below regulation limits leads to an increase in smoke emissions, further magnifying the emission control dilemma. Dimethyl ether (DME) contains suitable reactivity for compression ignition engines while also possessing distinct characteristics to diesel, notably physical properties such as volatility and high oxygen content, that eliminates engine-out soot concerns. In turn, DME enables direct NOx control via oxygen dilution. Nonetheless, the influence of charge dilution toward the combustion heat release behavior of DME persists. This study investigated heat release patterns of high-pressure DME combustion using a single-shot fuel scheduling, with injection timing fixed at top dead center (TDC). Throughout the study, the injection pressure, engine load, and oxygen dilution were adjusted separately to characterize their influence on the subsequent combustion process. Diesel combustion operated at matching conditions was used to provide relevance to the results. Most notably, the period of diffusion burning was extended in DME following a longer period of injection–combustion overlap. To add, the heat release of DME combustion was repeatedly shorter than diesel owing to the lack of end-burning combustion phase inherent to diesel combustion.
- 3 December 2022
- Published by Springer Nature
- p. 1-41
Access to Drinking Water, Food Security and Adequate Housing: Challenges for Engineering, Past, Present and Future
- 3 December 2022
- Published by Springer Nature
- p. 1-41
Access to Drinking Water, Food Security and Adequate Housing: Challenges for Engineering, Past, Present and Future
- 7 March 2020
- Published by Springer Nature in Springer Proceedings in Energy
- p. 1-35
“Tomorrow’s Energy, Renewables Alone?”
- 7 March 2020
- Published by Springer Nature in Springer Proceedings in Energy
- p. 1-35
“Tomorrow’s Energy, Renewables Alone?”
- 30 December 2018
- Published by Springer Nature
- p. 1-17
Energy and Sustainability: Policy, Politics and Practice
- 30 December 2018
- Published by Springer Nature
- p. 1-17
Energy and Sustainability: Policy, Politics and Practice
- 30 September 2014
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 137 (1) , 012205
Preliminary Investigation of Direct Injection Neat n-Butanol in a Diesel Engine
The characteristics of combustion, emissions, and thermal efficiency of a diesel engine with direct injection (DI) neat n-butanol were investigated. The engine ran at a load of 6.5–8.0 bar indicated mean effective pressure (IMEP) at 1500 rpm engine speed and the injection pressure was controlled to 900 bar. The intake boost pressure, injection timing, and EGR rate were adjusted to investigate the engine performance. The tests demonstrated that neat n-butanol had the potential to achieve ultralow emissions. However, challenges related to reducing the pressure rise rate and improving the ignition controllability were identified.
- 30 September 2014
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 137 (1) , 012205
Preliminary Investigation of Direct Injection Neat n-Butanol in a Diesel Engine
The characteristics of combustion, emissions, and thermal efficiency of a diesel engine with direct injection (DI) neat n-butanol were investigated. The engine ran at a load of 6.5–8.0 bar indicated mean effective pressure (IMEP) at 1500 rpm engine speed and the injection pressure was controlled to 900 bar. The intake boost pressure, injection timing, and EGR rate were adjusted to investigate the engine performance. The tests demonstrated that neat n-butanol had the potential to achieve ultralow emissions. However, challenges related to reducing the pressure rise rate and improving the ignition controllability were identified.
- 1 March 2008
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 24 (2) , 376-383
Investigation of Active Flow Control on Diesel Engine Aftertreatment
- 1 March 2008
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 24 (2) , 376-383
Investigation of Active Flow Control on Diesel Engine Aftertreatment