Kanao Fukuda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kanao Fukuda has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Joichi Sugimura
Kyushu University
8 shared publications - Shahira Liza
Malaysian- Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra, Kampung Datuk Keramat, 54100 Kuala Lumpur, Malaysia
5 shared publications Takehiro Morita
Machine Elements and Design Engineering Laboratory, Department of Mechanical Engineering, Faculty of Engineering Kyushu University Fukuoka Japan
5 shared publications- Noor Ayuma Mat Tahir
Univ Teknol Malaysia, Dept Mech Precis Engn, Tribol Precis & Machining TriPreM i khoza, Malaysia Japan Int Inst Technol, Jalan Sultan Yahya Petra, Kuala Lumpur 54100, Malaysia
4 shared publications Yoshinori Sawae
4 shared publicationsZaid Ali Subhi
Malaysia-Japan International Institute of Technology (MJIIT), Universiti Teknologi Malaysia
4 shared publications
Latest Publications
- 20 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 64518-64530
Influence of quartz–mullite synergy from fly ash and quarry dust on the hardness and tribological behavior of anodic oxide coatings
- 20 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 64518-64530
Influence of quartz–mullite synergy from fly ash and quarry dust on the hardness and tribological behavior of anodic oxide coatings
- 16 July 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (20) , 38372-38390
Enhanced mechanical properties and tribological performance of anodic oxide coating by using thermal power plant waste material
- 16 July 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (20) , 38372-38390
Enhanced mechanical properties and tribological performance of anodic oxide coating by using thermal power plant waste material
- Open Access
- 7 July 2024
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 19 (4) , 247-255
Review on Effect of Wide-Range Atmospheric Humidity, Ranging from Several vol ppb to 20,000 vol ppm, on the Dry Sliding Phenomena of Solid Materials
It is widely known that the impact of atmospheric humidity on tribological phenomena is significant, particularly in the context of dry sliding. Previous reviews have comprehensively addressed various cases within this domain and this article aims to complement these reviews with recent findings. The review covers a wide spectrum of humidity levels, ranging from trace amounts of water in the order of a few vol ppb to the relative humidity levels experienced in daily life. It delineates the forms of adsorbed water on solid surfaces within each humidity range and explores the potential physical lubrication mechanism of the adsorbed water and its effects on tribological phenomena. In the past, explanations for this influence have tended to be qualitative, primarily viewed from the perspective of chemical reactions. This discussion seeks to broaden the understanding by considering the influences from a physical lubrication perspective. Concluding the review, recent research findings are presented, shedding light on instances where trace amounts of water present in gases such as hydrogen exert an influence on tribological phenomena.
- 7 July 2024
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 19 (4) , 247-255
Open AccessReview on Effect of Wide-Range Atmospheric Humidity, Ranging from Several vol ppb to 20,000 vol ppm, on the Dry Sliding Phenomena of Solid Materials
It is widely known that the impact of atmospheric humidity on tribological phenomena is significant, particularly in the context of dry sliding. Previous reviews have comprehensively addressed various cases within this domain and this article aims to complement these reviews with recent findings. The review covers a wide spectrum of humidity levels, ranging from trace amounts of water in the order of a few vol ppb to the relative humidity levels experienced in daily life. It delineates the forms of adsorbed water on solid surfaces within each humidity range and explores the potential physical lubrication mechanism of the adsorbed water and its effects on tribological phenomena. In the past, explanations for this influence have tended to be qualitative, primarily viewed from the perspective of chemical reactions. This discussion seeks to broaden the understanding by considering the influences from a physical lubrication perspective. Concluding the review, recent research findings are presented, shedding light on instances where trace amounts of water present in gases such as hydrogen exert an influence on tribological phenomena.
- Open Access
- 31 October 2023
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 18 (6) , 339-352
Influences of Atmospheric Humidity on Sliding Speed Characteristics of Dry Sliding Phenomena
The effect of adsorbed water layers in sliding phenomena has been widely recognized, but it has yet to be explained thoroughly after many years of research. Previous researches tend to explain the phenomena from chemical and qualitative viewpoints, thus physical viewpoint approaches with quantitative evidence are necessary to complement the previous research works. Studies were done to estimate the thickness of adsorbed water layers in recent years to obtain quantitative evidence of the effect of adsorbed water layers. It was found that the thickness of the adsorbed water layer derived from atmospheric humidity could provide physical influences on sliding phenomena. The hypothesis in this study based on the Stribeck curve is; the friction coefficient may decrease significantly with the increase of sliding speed at high relative humidity (RH) compared to low RH. To verify the hypothesis, a pair of JIS SUS304 austenitic stainless steel balls were scratched against each other horizontally with a vertical overlapping distance of 80 µm at sliding speeds of 20, 200, and 2000 µm·s−1 in RH of 5, 55, and 95%. The experimental results supported the hypothesis as the friction coefficient for medium to high RH decreased significantly with increasing sliding speed while the friction coefficient decreases slightly at low RH. The friction coefficient decreases significantly at high sliding speed and RH. The possible physical effects of the adsorbed water layers were suggested.
- 31 October 2023
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 18 (6) , 339-352
Open AccessInfluences of Atmospheric Humidity on Sliding Speed Characteristics of Dry Sliding Phenomena
The effect of adsorbed water layers in sliding phenomena has been widely recognized, but it has yet to be explained thoroughly after many years of research. Previous researches tend to explain the phenomena from chemical and qualitative viewpoints, thus physical viewpoint approaches with quantitative evidence are necessary to complement the previous research works. Studies were done to estimate the thickness of adsorbed water layers in recent years to obtain quantitative evidence of the effect of adsorbed water layers. It was found that the thickness of the adsorbed water layer derived from atmospheric humidity could provide physical influences on sliding phenomena. The hypothesis in this study based on the Stribeck curve is; the friction coefficient may decrease significantly with the increase of sliding speed at high relative humidity (RH) compared to low RH. To verify the hypothesis, a pair of JIS SUS304 austenitic stainless steel balls were scratched against each other horizontally with a vertical overlapping distance of 80 µm at sliding speeds of 20, 200, and 2000 µm·s−1 in RH of 5, 55, and 95%. The experimental results supported the hypothesis as the friction coefficient for medium to high RH decreased significantly with increasing sliding speed while the friction coefficient decreases slightly at low RH. The friction coefficient decreases significantly at high sliding speed and RH. The possible physical effects of the adsorbed water layers were suggested.
- 12 August 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (21) , 34205-34222
Surface and tribology characterization of diamond-like carbon flakes reinforced oxide film by pulse anodizing
- 12 August 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (21) , 34205-34222
Surface and tribology characterization of diamond-like carbon flakes reinforced oxide film by pulse anodizing
- Open Access
Surface and Tribological Properties of Oxide Films on Aluminium Alloy through Fly-Ash Reinforcement
Hard anodizing has proven to be a helpful surface treatment for aluminium alloy and typically accompanied by the growth of a porous and highly flawed oxide layer. The presence of pores on the oxide surface can be taken as an advantage in improving the surface properties. Fly-ash particles are high in SiO2 and Al2O3 content and can be utilized as inexpensive strengthening particles, which can increase the wear resistance and microhardness of composite material. It was noticed that limited research had been carried out in utilizing fly-ash as reinforcement on composite oxide coating as a wear resistance candidate. Thus, this study focused on reinforcing fly-ash on oxide coating and investigating its tribological performance. The composite oxide coating was grown on AA2017 aluminium alloy through anodizing process. To understand the effect of anodizing time and fly-ash content, the parameters were varied from 5–60 min and 0–50 g/L, respectively. The findings suggested that 60 min of anodizing time provides the highest thickness and surface roughness at 35 µm and 6.5 µm, respectively. Interestingly, composite oxide coating with 50 g/L fly-ash provides the highest coating thickness but has the lowest roughness at 52 μm and 8.2 μm, respectively. The composite oxide coatings are observed to reduce friction only for a limited time, despite their potential in significantly reducing the wear rate. The wear mechanism observed was adhesion, micro-crack, and delamination. The findings of this study are believed to provide insight on the potential of fly-ash to be a reinforcement for wear-reduction materials.
Open AccessSurface and Tribological Properties of Oxide Films on Aluminium Alloy through Fly-Ash Reinforcement
Hard anodizing has proven to be a helpful surface treatment for aluminium alloy and typically accompanied by the growth of a porous and highly flawed oxide layer. The presence of pores on the oxide surface can be taken as an advantage in improving the surface properties. Fly-ash particles are high in SiO2 and Al2O3 content and can be utilized as inexpensive strengthening particles, which can increase the wear resistance and microhardness of composite material. It was noticed that limited research had been carried out in utilizing fly-ash as reinforcement on composite oxide coating as a wear resistance candidate. Thus, this study focused on reinforcing fly-ash on oxide coating and investigating its tribological performance. The composite oxide coating was grown on AA2017 aluminium alloy through anodizing process. To understand the effect of anodizing time and fly-ash content, the parameters were varied from 5–60 min and 0–50 g/L, respectively. The findings suggested that 60 min of anodizing time provides the highest thickness and surface roughness at 35 µm and 6.5 µm, respectively. Interestingly, composite oxide coating with 50 g/L fly-ash provides the highest coating thickness but has the lowest roughness at 52 μm and 8.2 μm, respectively. The composite oxide coatings are observed to reduce friction only for a limited time, despite their potential in significantly reducing the wear rate. The wear mechanism observed was adhesion, micro-crack, and delamination. The findings of this study are believed to provide insight on the potential of fly-ash to be a reinforcement for wear-reduction materials.
- 1 December 2021
- Published by Elsevier in Surface and Coatings Technology
- Vol. 428
The effect of humidity on friction behavior of hydrogenated HIPIMS W-C:H coatings
- 1 December 2021
- Published by Elsevier in Surface and Coatings Technology
- Vol. 428
The effect of humidity on friction behavior of hydrogenated HIPIMS W-C:H coatings
- 29 June 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (11) , 4263-4281
The relations between wear behavior and basic material properties of graphene‐based materials reinforced ultrahigh molecular weight polyethylene
This article aims to investigate the influence of reinforcing graphene oxide (GO) and graphite flakes (GF) fillers into ultrahigh molecular weight polyethylene (UHMWPE) for orthopedic application. These fillers were expected to physically bond to UHMWPE, thus can enhance the subsurface strength, improving the wear behavior of the composites. UHMWPE/GO and UHMWPE/GF composites were prepared at 0.1 and 1.0 wt% by melt‐blending, followed by a compression molding technique. A multidirectional pin‐on‐disc wear test was performed to simulate the kinematic of hip application. Whilst getting exposed in the artificial in‐vivo lubricant bath (30 v/v% diluted bovine serum). Following this, the wear mechanism fostered by each filler (GO and GF) was determined by wear features obtained from the optical microscope and scanning electron microscope (SEM). The crystallinity degree and crystal defect were assessed using x‐ray diffraction (XRD). The mechanical properties of fabricated composites were evaluated by using a universal testing machine and Vickers microhardness. We found that UHMWPE/GO has the lowest specific wear rate due to the improved subsurface strength, as the reduction of a weak adhesive point was observed on the worn surface. Meanwhile, higher GF content (1 wt%) in UHMWPE displayed a lower specific wear rate than neat UHMWPE after completing the 10 km sliding distance attributed to the filler resurfaced, responsible for providing a strong resistance of the shear stress applied upon sliding with the metal counterface. Interestingly, the hardness and tensile strength for both UHMWPE/GO and UHMWPE/GF increased, although the crystallinity percentage was declining compared to neat UHMWPE.
- 29 June 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (11) , 4263-4281
The relations between wear behavior and basic material properties of graphene‐based materials reinforced ultrahigh molecular weight polyethylene
This article aims to investigate the influence of reinforcing graphene oxide (GO) and graphite flakes (GF) fillers into ultrahigh molecular weight polyethylene (UHMWPE) for orthopedic application. These fillers were expected to physically bond to UHMWPE, thus can enhance the subsurface strength, improving the wear behavior of the composites. UHMWPE/GO and UHMWPE/GF composites were prepared at 0.1 and 1.0 wt% by melt‐blending, followed by a compression molding technique. A multidirectional pin‐on‐disc wear test was performed to simulate the kinematic of hip application. Whilst getting exposed in the artificial in‐vivo lubricant bath (30 v/v% diluted bovine serum). Following this, the wear mechanism fostered by each filler (GO and GF) was determined by wear features obtained from the optical microscope and scanning electron microscope (SEM). The crystallinity degree and crystal defect were assessed using x‐ray diffraction (XRD). The mechanical properties of fabricated composites were evaluated by using a universal testing machine and Vickers microhardness. We found that UHMWPE/GO has the lowest specific wear rate due to the improved subsurface strength, as the reduction of a weak adhesive point was observed on the worn surface. Meanwhile, higher GF content (1 wt%) in UHMWPE displayed a lower specific wear rate than neat UHMWPE after completing the 10 km sliding distance attributed to the filler resurfaced, responsible for providing a strong resistance of the shear stress applied upon sliding with the metal counterface. Interestingly, the hardness and tensile strength for both UHMWPE/GO and UHMWPE/GF increased, although the crystallinity percentage was declining compared to neat UHMWPE.
- Open Access
- 15 December 2019
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 14 (5) , 353-358
Tribological Behavior of Hydrophilic and Hydrophobic Surfaces in Atmosphere with Different Relative Humidity
The significant influences of atmospheric humidity on tribological phenomena are widely recognized. Although the influencing mechanisms of the humidity have been studied for a long time, many of the previous explanations remain in the qualitative estimation of mechanisms particularly from chemical effects viewpoint. In order to elucidate how the adsorbed water on a surface influences tribological phenomena, the current authors conducted ball to ball scratch tests for austenitic stainless steel (JIS SUS304) and proposed the mechanisms from a physical/mechanical viewpoint. A singular phenomenon was found; a lateral force, which can be regarded as a friction resistance, at a downhill motion showed significantly higher value than that at an uphill motion. The phenomenon was hypothesized to be influenced by Laplace pressure effect at a meniscus formed due to adsorbed water on the surface. In this study, polytetrafluoroethylene (PTFE) as the hydrophobic material was tested in comparison with SUS304 to show that the adsorbed water layer causes the singular phenomenon. PTFE successfully prevented the singular phenomenon while SUS304 reproduced it. The equilibrium analysis of the ball showed that adsorbed water contributed to the increase of the coefficient of kinetic friction but not of negative normal force at the contact point of SUS304.
- 15 December 2019
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 14 (5) , 353-358
Open AccessTribological Behavior of Hydrophilic and Hydrophobic Surfaces in Atmosphere with Different Relative Humidity
The significant influences of atmospheric humidity on tribological phenomena are widely recognized. Although the influencing mechanisms of the humidity have been studied for a long time, many of the previous explanations remain in the qualitative estimation of mechanisms particularly from chemical effects viewpoint. In order to elucidate how the adsorbed water on a surface influences tribological phenomena, the current authors conducted ball to ball scratch tests for austenitic stainless steel (JIS SUS304) and proposed the mechanisms from a physical/mechanical viewpoint. A singular phenomenon was found; a lateral force, which can be regarded as a friction resistance, at a downhill motion showed significantly higher value than that at an uphill motion. The phenomenon was hypothesized to be influenced by Laplace pressure effect at a meniscus formed due to adsorbed water on the surface. In this study, polytetrafluoroethylene (PTFE) as the hydrophobic material was tested in comparison with SUS304 to show that the adsorbed water layer causes the singular phenomenon. PTFE successfully prevented the singular phenomenon while SUS304 reproduced it. The equilibrium analysis of the ball showed that adsorbed water contributed to the increase of the coefficient of kinetic friction but not of negative normal force at the contact point of SUS304.
- 1 January 2015
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 10 (6) , 420-427
Analysis on the Mechanism of Humidity to Influence the Very Early Stage of Sliding under Different Load
- 1 January 2015
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 10 (6) , 420-427
Analysis on the Mechanism of Humidity to Influence the Very Early Stage of Sliding under Different Load