Kuniaki Dohda

Kuniaki Dohda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kuniaki Dohda has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Chemical Composition on Hot Extrudability and Tribological Behavior of 7000 Series Aluminum Alloys

    by Sukunthakan Ngernbamrung, Kuniaki Dohda, Tatsuya Funazuka, Junichi Oshima, Tomomi Shiratori

    Aluminum 7000 series alloys are widely used for aerospace and transportation applications due to their high strength-to-weight ratio. This research investigates the impact of zinc (Zn) and magnesium (Mg) content on the hot extrudability and tribological behavior. Elemental quantities straight away impact flow stress, determining the manufacturing parameters, whereas galling and adhesion frequently degrade tool life. This work illustrates that by assessing essential ram speeds and temperature limits, adjusting Zn and Mg concentrations considerably improves the extrudability limit. A decreasing flow stress during deformation reduces micro-cracking tendency and improves surface quality. The findings provide critical compositional guidelines for high-strength aluminum alloys, effectively balancing processing efficiency with improved surface quality and reduced element adhesion behavior, ensuring better industrial outcomes for advanced structural components.


  • Open Access

    Designs and applications of nitride coatings to hot metal forming dies

    by Kuniaki Dohda, Tatsuhiko Aizawa, Tatsuya Funazuka, Panuwat Soranansri, Keishi Okamoto

    Thin film coatings are widely applied to extend the service life of hot metal forming dies by improving wear resistance, reducing friction, and mitigating thermal and chemical damage. Nitride coatings deposited by Physical Vapor Deposition (PVD) and Chemical Vapor Deposition (CVD) methods have demonstrated potential to deal with critical challenges at the die-workpiece interface. This paper reviews the designs and applications of nitride coatings to hot metal forming dies. The discussion begins with the fundamentals and characteristics of monolithic, binary, and laminated coatings, which aim to enhance tribological performance at the interface. It then explores the application of nitride coatings used in the hot forming processes of steels, aluminum alloys, and other metal alloys. Finally, the review concludes with key highlights and recommendations for coatings selection and future research to improve the tribological performance of hot metal forming dies.

  • Open Access

    Tribological Performance of AlCrN, TiAlN, and Arc-DLC Coatings in Hot Forming of Aluminum Alloy

    by Panuwat Soranansri, André Dubois, Philippe Moreau, Tatsuya Funazuka, Kuniaki Dohda, Laurent Dubar

    This study aims to evaluate the tribological performance of commercial PVD coatings in alleviating material transfer under unlubricated contact in the hot forming of aluminum alloy. The commercial PVD coatings included AlCrN, TiAlN, and Arc-DLC coatings, deposited on the forming tool surface. The warm and hot upsetting sliding test (WHUST) was used as a friction test in this study to reproduce the severe contact conditions from the hot forming process of AA6082-T6 aluminum alloy. The WHUST was performed at 300 °C, 400 °C, and 500 °C to investigate the effect of temperature on the tribological performance of each coating. The results found that the AlCrN and TiAlN coatings exhibited similar performance. They dominated the initial aluminum transfer by adhesive bonding. In contrast, the Arc-DLC coating mainly caused the initial aluminum transfer by mechanical plowing due to its lower chemical affinity to the aluminum alloy. In addition, the tribological performance of each coating highly depended on the temperature. Higher temperatures resulted in both stronger intermetallic bonding at the interface and lower yield strength of the aluminum alloy. These behaviors led to the variations in the coefficient of friction, the 3D topography and the SEM morphology along the wear track of the specimen, and the thickness of the adhered aluminum layer on the coating surface. In comparison, the Arc-DLC coating provided better tribological performance in mitigating the aluminum transfer than the others.


  • Open Access

    Direct recycling of AA6063 chips by hot extrusion applying pseudo porthole die

    by T. Funazuka, Syun Yamashita, Takumi Urakawa, Tomomi Shiratori, Norio Takatsuji, K. Dohda

    Direct recycling of AA6063 chips by hot extrusion applying pseudo porthole die FUNAZUKA Tatsuya, YAMASHITA Syun, URAKAWA Takumi, SHIRATORI Tomomi, TAKATSUJI


  • Open Access

    Effect of CoCrMo Die and Tool Surface Nano-Texture on Micro Backward Extrusion Formability of AA6063-T6

    by Tatsuya Funazuka, Syunsuke Horiuchi, Kuniaki Dohda, Tomomi Shiratori

    To manufacture microparts used in medical and electronic devices, the machining scale must be reduced to the microscale. However, when applying existing plastic forming processes to the machining of microscale parts, the size effect caused by material properties and friction results in variations in product accuracy. To suppress the size effect, tool materials and tool surface treatments suitable for microscale machining must be considered. Using AA6063-T6 billets as test specimens, this study investigated the effects of tool surface properties, such as die surface nanotexture, on micro-extrudability such as extrusion force, product shape, and crystal structure of the product. A cobalt-chromium-molybdenum (CoCrMo) die was used as a new die material suitable for micro-extrusion. To investigate the effects of the die material and die surface nanotexture, AISI H13, CoCrMo, and nanotextured CoCrMo dies were used. The extrusion force increased rapidly with the progression of the stroke for both dies. Compared with the AISI H13 die, the CoCrMo die with nanotexture exhibited considerably lower extrusion force, longer extrusion length, and less adhesion on the die surface. The results of material analysis using electron backscatter diffraction indicated that the nanotextured CoCrMo die improved material flowability and facilitated the application of greater strain. In contrast, the AISI H13 die exhibited lower material flowability and nonuniform strain. Therefore, the tribology between the tool and material was controlled by changing the surface properties of the die to improve the formability.


  • Open Access

    Galling-free fine blanking of titanium plates by carbon-supersaturated tool steel punch

    by T. Aizawa, K. Fuchiwaki, K. Dohda

    The carbon supersaturated tool steel and high-speed steel punches were utilized to demonstrate that the titanium work materials were forged in high reduction of thickness and fine-blanked without adhesion of their fragments and deposition of their oxide debris particle. This galling free forging and fine blanking came from the in situ formation of the free carbon tribofilm only on the highly stressed interfaces between the punch/die and the titanium work. Under this in situ solid lubrication, the low frictional state was sustained to induce less bulging deformation of work during the forging process. The fine blanking of titanium plates advanced without adhesive wear and fractured regions on their sheared surface. The long life of tools was certified even in fine blanking of titanium and titanium alloy plates.


  • Open Access

    Effect of Punch Surface Microtexture on the Microextrudability of AA6063 Micro Backward Extrusion

    by Tatsuya Funazuka, Kuniaki Dohda, Tomomi Shiratori, Syunsuke Horiuchi, Ikumu Watanabe

    To apply conventional forming processes to microscale processing, the influence of size effects caused by material properties and friction effects must be considered. Herein, the effects of tool surface properties, such as punch surface texture, on microextrusion properties, such as extrusion force, product shape, and product microstructure, were investigated using AA6063 billets as test pieces. Millimeter-scale, microscale, and nanoscale textures were fabricated on the punch surfaces. Punch texturing was conducted by electrical discharge machining or polishing or using a laser process. The extrusion force increased rapidly as the stroke progressed for all punch textures. Comparing the product shapes, the smaller the texture size, the lower the adhesion and the longer the backward extrusion length. The results of material analysis using electron backscatter diffraction show that material flowability is improved, and more strain is uniformly applied when a nanoscale-textured punch is used. By contrast, when a mirror punch was used, material flowability decreased, and strain was applied non-uniformly. Therefore, by changing the surface properties of the punch, the tribology between the tool and material can be controlled, and formability can be improved.


  • Open Access

    Quantitative Characterization of the Affected Zones in a Single Crystal Fe-6Si Steel Sheet by Fine Piercing

    by Tatsuhiko Aizawa, Tomomi Shiratori, Tomoaki Yoshino, Yohei Suzuki, Kuniaki Dohda

    An iron loss in the motor core was often enhanced by formation of plastically affected zones in piercing the electrical steel sheets. A platform methodology to carry out quantitative evaluation of these affected zones in the pierced electrical steel sheets was proposed to search for the way to minimize the affected zone widths. A coarse-grained electrical steel sheet was employed as a work material for a fine piercing experiment under the narrowed clearance between the plasma-nitrided SKD11 punch and core-die. The shearing behavior by the applied loading for piercing was described by in situ measurement of the load-stroke relationship. The plastic straining in the single-crystal electrical steel sheet was characterized by SEM (scanning electron microscopy) and EBSD (electron back-scattering diffraction) to define the affected zone size and to analyze the rotation of crystallographic orientations by the induced plastic distortion during piercing. Integral and differentiation of spin rotation measured the affected zones. The effect of punch edge sharpness on these spin-rotation measures was also discussed using the nitrided and ion-milled SKD11 punch and core-die.


  • Open Access

    Effect of Punch Surface Grooves on Microformability of AA6063 Backward Microextrusion

    by Tatsuya Funazuka, Kuniaki Dohda, Tomomi Shiratori, Ryo Hiramiya, Ikumu Watanabe

    In order to apply conventional forming processes at the micro scale, the size effects caused by material properties and frictional effects must be taken into account. In this research, the effects of tool surface properties such as punch surface grooves on microextrudability, assessed using extrusion force, shape of the extrusion, and Vickers hardness, were investigated using an AA6063 billet. Microscale grooves of 5 to 10 µm were fabricated on the punch surface. The extrusion force increased rapidly as the stroke progressed for all the grooves. Comparing the product geometries showed that, the smaller the groove size, the lower the adhesion and the longer the backward extrusion length. The results of material analysis using EBSD showed that a 5 µm groove depth punch improved the material flowability and uniformly introduced more strain. On the other hand, material flowability was reduced and strain was applied nonuniformly when a mirror-finish tool was used. Therefore, the tribology between the tool and the material was controlled by changing the surface properties of the punch to improve formability.