Ikuo Kinoshita
Research Subjects
Ikuo Kinoshita has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Michio Murase
株式会社 原子力安全システム研究
5 shared publications Akio Tomiyama
3 shared publications- Dirk Lucas
Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden - Rossendorf, Dresden, Germany
2 shared publications Takashi Hibiki
School of Nuclear Engineering, Purdue University, West Lafayette, IN, USA
2 shared publications- Toshihide Torige
Institute of Nuclear Safety System, Inc. (INSS), 64 Sata, Mihama-cho, Mikata-gun, Fukui 919-1205, Japan
2 shared publications - Yoichi Utanohara
Institute of Nuclear Safety System, Inc. , 64 Sata, Mihama-cho, Mikata-gun, Fukui 919-1205, Japan
2 shared publications
Latest Publications
- Open Access
- 15 October 2024
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 302, 17001
Quantum Circuit Learning for Uncertainty Quantification of RELAP5 Code Analysis of ROSA/LSTF Small Break LOCA Tests
To reduce the computational demand in the best estimate plus uncertainty (BEPU) analysis, an accurate and inexpensive machine learning model is expected to be used to replace the high-fidelity RELAP5 code for rapid determination of the uncertainties on the figure of merit of interest. One of the problems associated with the application of a machine learning is overlearning. Quantum circuit learning is the quantum analogue of classical deep learning, which is expected to be less prone to overlearning because the optimized parameters are bound by unitary transformations in the quantum circuit. In this paper, quantum circuit learning is applied to the BEPU analysis of the fuel peak cladding temperature (PCT) for a small-break LOCA scenario in PWRs. The parameterized quantum circuit is trained using a small number of the RELAP5 analysis results and the prediction accuracy of the 95th percentile value of the PCTs is investigated. By optimizing the multipliers of the measured basis, the 95th percentile value of the PCTs predicted by the quantum circuit learning resulted in better accuracy and smaller variability than order statistics and linear quadratic regressions.
- 15 October 2024
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 302, 17001
Open AccessQuantum Circuit Learning for Uncertainty Quantification of RELAP5 Code Analysis of ROSA/LSTF Small Break LOCA Tests
To reduce the computational demand in the best estimate plus uncertainty (BEPU) analysis, an accurate and inexpensive machine learning model is expected to be used to replace the high-fidelity RELAP5 code for rapid determination of the uncertainties on the figure of merit of interest. One of the problems associated with the application of a machine learning is overlearning. Quantum circuit learning is the quantum analogue of classical deep learning, which is expected to be less prone to overlearning because the optimized parameters are bound by unitary transformations in the quantum circuit. In this paper, quantum circuit learning is applied to the BEPU analysis of the fuel peak cladding temperature (PCT) for a small-break LOCA scenario in PWRs. The parameterized quantum circuit is trained using a small number of the RELAP5 analysis results and the prediction accuracy of the 95th percentile value of the PCTs is investigated. By optimizing the multipliers of the measured basis, the 95th percentile value of the PCTs predicted by the quantum circuit learning resulted in better accuracy and smaller variability than order statistics and linear quadratic regressions.
- 17 December 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 57 (5) , 553-572
Improved drift-flux correlation to enhance the prediction of void fraction in nuclear reactor fuel bundles at low flow and elevated pressure conditions
The EPRI (1991) and the Clark et al. (2014) drift-flux correlations implemented in RELAP5/MOD3 code were benchmarked against the low-pressure void fraction data collected by Clark et al. (2014) at Purdue University and the high-pressure data collected by Anklam and Miller (1982) at ORNL. The Clark et al. correlation (2014) was found to perform best at low pressures of Clark et al. tests (2014), but the accuracy was deteriorated at higher pressures of Anklam and Miller tests (1982). To account for this effect, a pressure scaling factor has been added to the distribution parameter correlation to reduce the distribution parameter peaking at high pressures. This factor is dependent on the density ratio and it eliminates the distribution parameter enhancement effect for pressures over 0.5 MPa. It was confirmed that the new correlation with the correction improved the void fraction prediction performance at a higher pressure of Anklam and Miller tests (1982). The new correlation provides a transition between the Clark et al. correlation (2014) at low pressures and the correlation of Ozaki et al. (2013) and Ozaki and Hibiki (2015) at high pressures, which is excellent both in physical characteristics and scalability of two-phase flow in rod bundles.
- 17 December 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 57 (5) , 553-572
Improved drift-flux correlation to enhance the prediction of void fraction in nuclear reactor fuel bundles at low flow and elevated pressure conditions
The EPRI (1991) and the Clark et al. (2014) drift-flux correlations implemented in RELAP5/MOD3 code were benchmarked against the low-pressure void fraction data collected by Clark et al. (2014) at Purdue University and the high-pressure data collected by Anklam and Miller (1982) at ORNL. The Clark et al. correlation (2014) was found to perform best at low pressures of Clark et al. tests (2014), but the accuracy was deteriorated at higher pressures of Anklam and Miller tests (1982). To account for this effect, a pressure scaling factor has been added to the distribution parameter correlation to reduce the distribution parameter peaking at high pressures. This factor is dependent on the density ratio and it eliminates the distribution parameter enhancement effect for pressures over 0.5 MPa. It was confirmed that the new correlation with the correction improved the void fraction prediction performance at a higher pressure of Anklam and Miller tests (1982). The new correlation provides a transition between the Clark et al. correlation (2014) at low pressures and the correlation of Ozaki et al. (2013) and Ozaki and Hibiki (2015) at high pressures, which is excellent both in physical characteristics and scalability of two-phase flow in rod bundles.
- 28 May 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 56 (7) , 588-598
Development of drift–flux correlation for predicting void fraction in downcomer regions
Accurate prediction of interfacial drag in the downcomer annulus is crucial for the assessment of downcomer void fraction for the loss of coolant accident analysis. The downcomer annulus is the gap between reactor pressure vessel (RPV) exterior and the inner wall of pressure containment vessel (PCV). Based on the previous research, occurrence of the nonuniform two-phase flow in downcomer section is reported, which is partly due to the large wall temperature difference between RPV exterior and the inner wall of PCV. In RELAP5, interfacial drag term in downcomer section is calculated using Kataoka–Ishii and churn-turbulent drift–flux correlations. It has been pointed out that this traditional calculation approach for calculating downcomer void fraction needs modification. The purpose of the current study is to assess the behaviors of drift–flux parameters in downcomer section and to propose an improved distribution parameter model that is suitable for donwcomer boiling analysis.
- 28 May 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 56 (7) , 588-598
Development of drift–flux correlation for predicting void fraction in downcomer regions
Accurate prediction of interfacial drag in the downcomer annulus is crucial for the assessment of downcomer void fraction for the loss of coolant accident analysis. The downcomer annulus is the gap between reactor pressure vessel (RPV) exterior and the inner wall of pressure containment vessel (PCV). Based on the previous research, occurrence of the nonuniform two-phase flow in downcomer section is reported, which is partly due to the large wall temperature difference between RPV exterior and the inner wall of PCV. In RELAP5, interfacial drag term in downcomer section is calculated using Kataoka–Ishii and churn-turbulent drift–flux correlations. It has been pointed out that this traditional calculation approach for calculating downcomer void fraction needs modification. The purpose of the current study is to assess the behaviors of drift–flux parameters in downcomer section and to propose an improved distribution parameter model that is suitable for donwcomer boiling analysis.
- 1 January 2019
- Published by Research Publishing Services
- p. 3752-3757
A Limit Surface Prediction for PWR LOCA Transients Using Adaptive Machine Learning Techniques
- 1 January 2019
- Published by Research Publishing Services
- p. 3752-3757
A Limit Surface Prediction for PWR LOCA Transients Using Adaptive Machine Learning Techniques
- 1 August 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 94, 230-240
Uncertainty in RELAP5/MOD3.2 calculations for interfacial drag in downward two-phase flow
- 1 August 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 94, 230-240
Uncertainty in RELAP5/MOD3.2 calculations for interfacial drag in downward two-phase flow
- 29 February 2016
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 2 (2) , 021003
Uncertainty Quantification of the RELAP5 Interfacial Friction Model in the Rod Bundle Geometry
Interfacial friction in the core affects the two-phase mixture level and the distribution of the dispersed gas phase during a small-break loss-of-coolant accident (LOCA). The RELAP5/MOD3.2 code uses the drift flux model to describe the interfacial friction force in vertical dispersed flow, and the Chexal–Lellouche drift flux correlation is used for the rod bundle geometry. In the present study, the RELAP5 model uncertainty was quantified for the bubbly–slug interfacial friction model in the rod bundle geometry by conducting numerical analyses of void profile tests in the Thermal Hydraulic Test Facility (THTF) of the Oak Ridge National Laboratory (ORNL). The model uncertainty parameter was defined as a multiplier for the interfacial friction coefficient. Numerical analyses were performed by adjusting the multiplier so that the predicted void fractions agreed with the measured test data. The resultant distribution of the multipliers represented the interfacial friction model uncertainty.
- 29 February 2016
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 2 (2) , 021003
Uncertainty Quantification of the RELAP5 Interfacial Friction Model in the Rod Bundle Geometry
Interfacial friction in the core affects the two-phase mixture level and the distribution of the dispersed gas phase during a small-break loss-of-coolant accident (LOCA). The RELAP5/MOD3.2 code uses the drift flux model to describe the interfacial friction force in vertical dispersed flow, and the Chexal–Lellouche drift flux correlation is used for the rod bundle geometry. In the present study, the RELAP5 model uncertainty was quantified for the bubbly–slug interfacial friction model in the rod bundle geometry by conducting numerical analyses of void profile tests in the Thermal Hydraulic Test Facility (THTF) of the Oak Ridge National Laboratory (ORNL). The model uncertainty parameter was defined as a multiplier for the interfacial friction coefficient. Numerical analyses were performed by adjusting the multiplier so that the predicted void fractions agreed with the measured test data. The resultant distribution of the multipliers represented the interfacial friction model uncertainty.
- 3 September 2015
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 1 (4) , 041009
Countercurrent Flow Limitation in Slightly Inclined Pipes With Elbows
One-dimensional (1D) sensitivity computations were carried out for air–water countercurrent flows in a -scale model of the hot leg and a -scale model of the pressurizer surge line in a pressurized water reactor (PWR) to generalize the prediction method for countercurrent flow limitation (CCFL) characteristics in slightly inclined pipes with elbows. In the 1D model, the wall friction coefficient of single-phase gas flows was used. The interfacial drag coefficient of , an appropriate adjustment factor of for the wall friction coefficient of single-phase liquid flows ( for of single-phase gas flows), and an appropriate adjustment factor of for the pressure loss coefficient of elbows in single-phase flows were determined to give good agreement between the computed and measured CCFL characteristics. The adjusted factors were used to compute and then discuss effects of the inclination angle and diameter on CCFL characteristics.- 3 September 2015
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 1 (4) , 041009
Countercurrent Flow Limitation in Slightly Inclined Pipes With Elbows
One-dimensional (1D) sensitivity computations were carried out for air–water countercurrent flows in a -scale model of the hot leg and a -scale model of the pressurizer surge line in a pressurized water reactor (PWR) to generalize the prediction method for countercurrent flow limitation (CCFL) characteristics in slightly inclined pipes with elbows. In the 1D model, the wall friction coefficient of single-phase gas flows was used. The interfacial drag coefficient of , an appropriate adjustment factor of for the wall friction coefficient of single-phase liquid flows ( for of single-phase gas flows), and an appropriate adjustment factor of for the pressure loss coefficient of elbows in single-phase flows were determined to give good agreement between the computed and measured CCFL characteristics. The adjusted factors were used to compute and then discuss effects of the inclination angle and diameter on CCFL characteristics.- 6 June 2014
- Published by EDP Sciences
- p. 05111
Sensitivity Analyses in Small Break LOCA with HPI-Failure: Effect of Break-Size in Secondary-Side Depressurization
In the case of total failure of the high pressure injection (HPI) system following small break loss of coolant accident (SBLOCA) in pressurized water reactor (PWR), the break size is so small that the primary system does not depressurize to the accumulator (ACC) injection pressure before the core is uncovered extensively. Therefore, steam generator (SG) secondary-side depressurization is necessary as an accident management in order to grant accumulator system actuation and core reflood. A thermal-hydraulic analysis using RELAP5/MOD3 was made on SBLOCA with HPI-failure for Oi Units 3/4 operated by Kansai Electoric Power Co., which are conventional 4 loop PWR plants. The effectiveness of SG secondary-side depressurization procedure was investigated for the real plant design and operational characteristics. The sensitivity analyses using RELAP5/MOD3.2 showed that the accident management was effective for a wide range of break sizes, various orientations and positions. The critical break can be 3 inch cold-leg bottom break.
- 6 June 2014
- Published by EDP Sciences
- p. 05111
Sensitivity Analyses in Small Break LOCA with HPI-Failure: Effect of Break-Size in Secondary-Side Depressurization
In the case of total failure of the high pressure injection (HPI) system following small break loss of coolant accident (SBLOCA) in pressurized water reactor (PWR), the break size is so small that the primary system does not depressurize to the accumulator (ACC) injection pressure before the core is uncovered extensively. Therefore, steam generator (SG) secondary-side depressurization is necessary as an accident management in order to grant accumulator system actuation and core reflood. A thermal-hydraulic analysis using RELAP5/MOD3 was made on SBLOCA with HPI-failure for Oi Units 3/4 operated by Kansai Electoric Power Co., which are conventional 4 loop PWR plants. The effectiveness of SG secondary-side depressurization procedure was investigated for the real plant design and operational characteristics. The sensitivity analyses using RELAP5/MOD3.2 showed that the accident management was effective for a wide range of break sizes, various orientations and positions. The critical break can be 3 inch cold-leg bottom break.
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of the National Symposium on Power and Energy Systems
- Vol. 2014.19, 161-162
F114 Investigation of Scale-up Capability of RELAP5 Code via ROSA/LSTF Small Break LOCA Tests
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of the National Symposium on Power and Energy Systems
- Vol. 2014.19, 161-162
F114 Investigation of Scale-up Capability of RELAP5 Code via ROSA/LSTF Small Break LOCA Tests
- 1 August 2012
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 249, 14-23
Numerical simulations for steam–water CCFL tests using the 1/3 scale rectangular channel simulating a PWR hot leg
- 1 August 2012
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 249, 14-23
Numerical simulations for steam–water CCFL tests using the 1/3 scale rectangular channel simulating a PWR hot leg