Oksana Mukhametdinova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Oksana Mukhametdinova has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- E. V. Avtokratova
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
4 shared publications - Oleg Sitdikov
Russian Academy of Sciences
3 shared publications - Михаил Вячеславович Маркушев
Institute for Metals Superplasticity Problems, Russian Academy of Sciences, Ufa, Russia
3 shared publications - Dayan Nugmanov
Institute of Nanotechnology, Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany
1 shared publication Michael Markushev
Institute for Metals Superplasticity Problems RAS, Ufa, 450001 Russia
1 shared publication- O. Sh. Sitdikov
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
1 shared publication
Latest Publications
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Ultrafine grain structure processing in Al-Mg-Sc-Zr alloy under severe ABC forging at elevated temperature
The effect of multidirectional (abc) forging (MDF) to the strain of about 8.5 at 325°C (∼0.65Tm) and 10−2 s−1 on the grain refinement of a 1570C Al-Mg-Sc-Zr alloy was investigated. The cast and homogenized alloy had an equiaxed microstructure with the grain size of ∼25 µm and nearly uniform distribution of nanosized (∼5–10 nm in diameter) coherent dispersoids Al3(Sc, Zr). In the early MDF stages, new fine (sub)grains with low- and high-angle misorientations were preferably formed in grain interiors and near original grain boundaries, respectively. With increasing strain, the mean boundary misorientation gradually increased resulting in almost completely recrystallized structure with the grain size of ∼1.3 µm and the fraction of high-angle boundaries ∼0.85. The strain dependency of microstructural parameters suggested that grain refinement occurred via continuous dynamic recrystallization. The role of disperse phases in the structural alloy behavior is discussed.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Ultrafine grain structure processing in Al-Mg-Sc-Zr alloy under severe ABC forging at elevated temperature
The effect of multidirectional (abc) forging (MDF) to the strain of about 8.5 at 325°C (∼0.65Tm) and 10−2 s−1 on the grain refinement of a 1570C Al-Mg-Sc-Zr alloy was investigated. The cast and homogenized alloy had an equiaxed microstructure with the grain size of ∼25 µm and nearly uniform distribution of nanosized (∼5–10 nm in diameter) coherent dispersoids Al3(Sc, Zr). In the early MDF stages, new fine (sub)grains with low- and high-angle misorientations were preferably formed in grain interiors and near original grain boundaries, respectively. With increasing strain, the mean boundary misorientation gradually increased resulting in almost completely recrystallized structure with the grain size of ∼1.3 µm and the fraction of high-angle boundaries ∼0.85. The strain dependency of microstructural parameters suggested that grain refinement occurred via continuous dynamic recrystallization. The role of disperse phases in the structural alloy behavior is discussed.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1783 (1) , 020160
Effect of the size of transition-metal aluminides on the structure of 1570C aluminum alloy processed by hot multidirectional isothermal forging
The effect of the size of nanoscale Al 3(Sc, Zr) precipitates on the grain refinement in 1570C Al alloy (Al-5Mg-0.2Sc-0.08Zr-0.002Be) during multidirectional isothermal forging (MIF) to the total true strain 4.2 at 450°C (0.77T m) is investigated. At early MIF stages, arrays of new fine (sub)grains with low- and high-angle boundaries are formed near original grain boundaries followed by an increase in their number and boundary misorientations at larger strains. It is shown that in an alloy with finer dispersoids the grain structure with a less volume fraction and size of fine grains as well as with a less fraction of high-angle boundaries and average misorientation of deformation-induced boundaries is developed. The role of dispersed phases in the alloy grain refinement at elevated temperature is discussed.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1783 (1) , 020160
Effect of the size of transition-metal aluminides on the structure of 1570C aluminum alloy processed by hot multidirectional isothermal forging
The effect of the size of nanoscale Al 3(Sc, Zr) precipitates on the grain refinement in 1570C Al alloy (Al-5Mg-0.2Sc-0.08Zr-0.002Be) during multidirectional isothermal forging (MIF) to the total true strain 4.2 at 450°C (0.77T m) is investigated. At early MIF stages, arrays of new fine (sub)grains with low- and high-angle boundaries are formed near original grain boundaries followed by an increase in their number and boundary misorientations at larger strains. It is shown that in an alloy with finer dispersoids the grain structure with a less volume fraction and size of fine grains as well as with a less fraction of high-angle boundaries and average misorientation of deformation-induced boundaries is developed. The role of dispersed phases in the alloy grain refinement at elevated temperature is discussed.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1683, 020155
Effect of equal channel angular pressing on structure and superplasticity of non-heat hardenable Al-Mg-Sc-Zr alloy
Microstructure and superplastic behavior of the aluminum alloy 1570C (Al-5Mg-0.2Sc-0.08Zr) after equal channel angular pressing (ECAP) to the strains of e ∼ 3 and 8 at the temperature of 325°C have been analyzed. ECAP to e ∼ 3 resulted in the partially recrystallized structure with the volume fraction and size of new grains of about 30% and 1–2 µm, consequently. The alloy with such structure exhibited the high-strain rate superplasticity with elongations >2000% at strain rates ∼10−2 s−1 and temperatures 475–520°C. After ECAP to e ∼ 8, the structure became more uniform with ∼70% of grains of ∼1 μm in size. This promoted both low-temperature and high-strain rate superplasticity with maximum elongations ∼1000 and 3300% at 350°C and 1.4×10−2 s−1 and at 475°C and 5.6×10−2 s−1, respectively. The nature of the alloy superplastic behavior is discussed.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1683, 020155
Effect of equal channel angular pressing on structure and superplasticity of non-heat hardenable Al-Mg-Sc-Zr alloy
Microstructure and superplastic behavior of the aluminum alloy 1570C (Al-5Mg-0.2Sc-0.08Zr) after equal channel angular pressing (ECAP) to the strains of e ∼ 3 and 8 at the temperature of 325°C have been analyzed. ECAP to e ∼ 3 resulted in the partially recrystallized structure with the volume fraction and size of new grains of about 30% and 1–2 µm, consequently. The alloy with such structure exhibited the high-strain rate superplasticity with elongations >2000% at strain rates ∼10−2 s−1 and temperatures 475–520°C. After ECAP to e ∼ 8, the structure became more uniform with ∼70% of grains of ∼1 μm in size. This promoted both low-temperature and high-strain rate superplasticity with maximum elongations ∼1000 and 3300% at 350°C and 1.4×10−2 s−1 and at 475°C and 5.6×10−2 s−1, respectively. The nature of the alloy superplastic behavior is discussed.