E. V. Avtokratova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
E. V. Avtokratova has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Михаил Вячеславович Маркушев
Institute for Metals Superplasticity Problems, Russian Academy of Sciences, Ufa, Russia
10 shared publications - Oleg Sitdikov
Russian Academy of Sciences
7 shared publications - O. Sh. Sitdikov
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
4 shared publications - Oksana Mukhametdinova
Institute for Metals Superplasticity Problems RAS, Ufa, 450001 Russia
4 shared publications - R. R. Ilyasov
Institute for Metals Superplasticity Problems RAS, Ufa, 450001 Russia
4 shared publications - Stanislav Vatslavovich Krymskiy
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
4 shared publications
Latest Publications
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- Open Access
- 20 December 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (4) , 491-500
МИКРОСТРУКТУРНЫЕ ИЗМЕНЕНИЯ В СПЛАВЕ Al-3 вес. % Cu В ПРОЦЕССЕ РАВНОКАНАЛЬНОГО УГЛОВОГО ПРЕССОВАНИЯ ПРИ ПОВЫШЕННОЙ ТЕМПЕРАТУРЕ
Исследовали изменение микроструктуры крупнозернистого бинарного сплава Al-3 вес. % Cu в процессе равноканального углового (РКУ) прессования при Т=150 °C ≈ 0,5Тпл (где Tпл – температура плавления чистого алюминия). Перед началом деформации в сплаве были получены гомогенные выделения упрочняющей фазы Q(Al2Cu) со средним размером около 16 нм. Как и в условиях низкотемпературной деформации, основной особенностью РКУ прессования данного сплава при 0,5Тпл было развитие на начальной стадии деформации (e=1) полосовых деформационных структур, приводящих к фрагментации исходных зерен. Однако, при дальнейшем РКУ прессовании такие дислокационные структуры трансформировались в характерную для горячей деформации смешанную (суб)зеренную структуру, что сопровождалось измельчением зерен. В результате при e=8 в сплаве формировалась бимодальная микроструктура с долей высокоугловых границ около 50 %, состоящая на 60 % из областей новых зерен размером около 1 мкм и нерекристаллизованных фрагментов исходных зерен, содержащих субзерна. Показано, что в отсутствие дисперсных алюминидов переходных металлов выделения основной упрочняющей фазы Q оказывали существенное влияние на процессы накопления и релаксации энергии деформации. В результате эти выделения контролировали формирование дислокационной структуры, протекание динамического возврата и миграцию границ (суб)зерен, определяя характер и кинетику процессов формирования новой мелкозернистой структуры.
- 20 December 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (4) , 491-500
Open AccessМИКРОСТРУКТУРНЫЕ ИЗМЕНЕНИЯ В СПЛАВЕ Al-3 вес. % Cu В ПРОЦЕССЕ РАВНОКАНАЛЬНОГО УГЛОВОГО ПРЕССОВАНИЯ ПРИ ПОВЫШЕННОЙ ТЕМПЕРАТУРЕ
Исследовали изменение микроструктуры крупнозернистого бинарного сплава Al-3 вес. % Cu в процессе равноканального углового (РКУ) прессования при Т=150 °C ≈ 0,5Тпл (где Tпл – температура плавления чистого алюминия). Перед началом деформации в сплаве были получены гомогенные выделения упрочняющей фазы Q(Al2Cu) со средним размером около 16 нм. Как и в условиях низкотемпературной деформации, основной особенностью РКУ прессования данного сплава при 0,5Тпл было развитие на начальной стадии деформации (e=1) полосовых деформационных структур, приводящих к фрагментации исходных зерен. Однако, при дальнейшем РКУ прессовании такие дислокационные структуры трансформировались в характерную для горячей деформации смешанную (суб)зеренную структуру, что сопровождалось измельчением зерен. В результате при e=8 в сплаве формировалась бимодальная микроструктура с долей высокоугловых границ около 50 %, состоящая на 60 % из областей новых зерен размером около 1 мкм и нерекристаллизованных фрагментов исходных зерен, содержащих субзерна. Показано, что в отсутствие дисперсных алюминидов переходных металлов выделения основной упрочняющей фазы Q оказывали существенное влияние на процессы накопления и релаксации энергии деформации. В результате эти выделения контролировали формирование дислокационной структуры, протекание динамического возврата и миграцию границ (суб)зерен, определяя характер и кинетику процессов формирования новой мелкозернистой структуры.
- 27 November 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (2) , 505-525
Structural Characterization of Binary Al-Cu Alloy Processed by Equal Channel Angular Pressing at Half of the Melting Point
- 27 November 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (2) , 505-525
Structural Characterization of Binary Al-Cu Alloy Processed by Equal Channel Angular Pressing at Half of the Melting Point
- Open Access
- 19 November 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2167 (1) , 020186
Electrochemical corrosion of cryorolled and aged aluminum alloy
Structural factors influencing the electrochemical corrosion of 2024 aluminum alloy after conventional strengthening heat treatment and its combination with isothermal rolling at liquid-nitrogen temperature were studied using optical metallography, transmission electron microscopy and electrochemical tests. It is established that the cryorolled and naturally aged alloy demonstrated relatively high corrosion resistance, which sharply decreased with artificial aging at 190 °C. Such a loss of corrosion resistance is caused by the accelerated decomposition of the preliminary supersaturated aluminum solid solution, accompanied by the formation of the mixed structure of the matrix, consisting of recovered and recrystallized areas with a bimodal distribution of main strengthening phases. It is concluded that corrosion of the cryorolled and aged alloy has a common nature and is mainly depends on the phase factors.
- 19 November 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2167 (1) , 020186
Open AccessElectrochemical corrosion of cryorolled and aged aluminum alloy
Structural factors influencing the electrochemical corrosion of 2024 aluminum alloy after conventional strengthening heat treatment and its combination with isothermal rolling at liquid-nitrogen temperature were studied using optical metallography, transmission electron microscopy and electrochemical tests. It is established that the cryorolled and naturally aged alloy demonstrated relatively high corrosion resistance, which sharply decreased with artificial aging at 190 °C. Such a loss of corrosion resistance is caused by the accelerated decomposition of the preliminary supersaturated aluminum solid solution, accompanied by the formation of the mixed structure of the matrix, consisting of recovered and recrystallized areas with a bimodal distribution of main strengthening phases. It is concluded that corrosion of the cryorolled and aged alloy has a common nature and is mainly depends on the phase factors.
- Open Access
- 1 January 2017
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 7 (3)
Structure of the aluminum alloy 1570C subjected to multidirectional forging with decreasing temperature
- 1 January 2017
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 7 (3)
Open AccessStructure of the aluminum alloy 1570C subjected to multidirectional forging with decreasing temperature
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1909, 020133
Effect of S-phase precipitates on deformation nanostructuring and hardening of 2xxx aluminum alloy
The influence of preliminary heat treatment, involving quenching and further aging at 190°C for 10 h, on the grain structure, hardness, and tensile strength of hot-pressed commercial D16 alloy severely deformed via room-temperature high pressure torsion (HPT) (10 revolutions under P = 6 GPa) was investigated. In spite of higher deformation strengthening, owing to the formation of a more developed nanostructure in the prequenched material, the alloy hardness and strength in both HPT conditions (i.e. after quenching and further aging) were quite similar. The nature of the alloy structure-property relations found is discussed.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1909, 020133
Effect of S-phase precipitates on deformation nanostructuring and hardening of 2xxx aluminum alloy
The influence of preliminary heat treatment, involving quenching and further aging at 190°C for 10 h, on the grain structure, hardness, and tensile strength of hot-pressed commercial D16 alloy severely deformed via room-temperature high pressure torsion (HPT) (10 revolutions under P = 6 GPa) was investigated. In spite of higher deformation strengthening, owing to the formation of a more developed nanostructure in the prequenched material, the alloy hardness and strength in both HPT conditions (i.e. after quenching and further aging) were quite similar. The nature of the alloy structure-property relations found is discussed.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Ultrafine grain structure processing in Al-Mg-Sc-Zr alloy under severe ABC forging at elevated temperature
The effect of multidirectional (abc) forging (MDF) to the strain of about 8.5 at 325°C (∼0.65Tm) and 10−2 s−1 on the grain refinement of a 1570C Al-Mg-Sc-Zr alloy was investigated. The cast and homogenized alloy had an equiaxed microstructure with the grain size of ∼25 µm and nearly uniform distribution of nanosized (∼5–10 nm in diameter) coherent dispersoids Al3(Sc, Zr). In the early MDF stages, new fine (sub)grains with low- and high-angle misorientations were preferably formed in grain interiors and near original grain boundaries, respectively. With increasing strain, the mean boundary misorientation gradually increased resulting in almost completely recrystallized structure with the grain size of ∼1.3 µm and the fraction of high-angle boundaries ∼0.85. The strain dependency of microstructural parameters suggested that grain refinement occurred via continuous dynamic recrystallization. The role of disperse phases in the structural alloy behavior is discussed.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Ultrafine grain structure processing in Al-Mg-Sc-Zr alloy under severe ABC forging at elevated temperature
The effect of multidirectional (abc) forging (MDF) to the strain of about 8.5 at 325°C (∼0.65Tm) and 10−2 s−1 on the grain refinement of a 1570C Al-Mg-Sc-Zr alloy was investigated. The cast and homogenized alloy had an equiaxed microstructure with the grain size of ∼25 µm and nearly uniform distribution of nanosized (∼5–10 nm in diameter) coherent dispersoids Al3(Sc, Zr). In the early MDF stages, new fine (sub)grains with low- and high-angle misorientations were preferably formed in grain interiors and near original grain boundaries, respectively. With increasing strain, the mean boundary misorientation gradually increased resulting in almost completely recrystallized structure with the grain size of ∼1.3 µm and the fraction of high-angle boundaries ∼0.85. The strain dependency of microstructural parameters suggested that grain refinement occurred via continuous dynamic recrystallization. The role of disperse phases in the structural alloy behavior is discussed.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1783 (1) , 020160
Effect of the size of transition-metal aluminides on the structure of 1570C aluminum alloy processed by hot multidirectional isothermal forging
The effect of the size of nanoscale Al 3(Sc, Zr) precipitates on the grain refinement in 1570C Al alloy (Al-5Mg-0.2Sc-0.08Zr-0.002Be) during multidirectional isothermal forging (MIF) to the total true strain 4.2 at 450°C (0.77T m) is investigated. At early MIF stages, arrays of new fine (sub)grains with low- and high-angle boundaries are formed near original grain boundaries followed by an increase in their number and boundary misorientations at larger strains. It is shown that in an alloy with finer dispersoids the grain structure with a less volume fraction and size of fine grains as well as with a less fraction of high-angle boundaries and average misorientation of deformation-induced boundaries is developed. The role of dispersed phases in the alloy grain refinement at elevated temperature is discussed.
- 1 January 2016
- Published by AIP Publishing
- Vol. 1783 (1) , 020160
Effect of the size of transition-metal aluminides on the structure of 1570C aluminum alloy processed by hot multidirectional isothermal forging
The effect of the size of nanoscale Al 3(Sc, Zr) precipitates on the grain refinement in 1570C Al alloy (Al-5Mg-0.2Sc-0.08Zr-0.002Be) during multidirectional isothermal forging (MIF) to the total true strain 4.2 at 450°C (0.77T m) is investigated. At early MIF stages, arrays of new fine (sub)grains with low- and high-angle boundaries are formed near original grain boundaries followed by an increase in their number and boundary misorientations at larger strains. It is shown that in an alloy with finer dispersoids the grain structure with a less volume fraction and size of fine grains as well as with a less fraction of high-angle boundaries and average misorientation of deformation-induced boundaries is developed. The role of dispersed phases in the alloy grain refinement at elevated temperature is discussed.